BOSSIN 18-SHFP-BLK PTC Fan Heater Instruction Manual
- June 8, 2024
- BOSSIN
Table of Contents
BOSSIN 18-SHFP-BLK PTC Fan Heater
WARNING
Thank you for purchasing your new heater.
These operating instructions will help you use it properly and safely.
We recommend that you spend some time reading this instruction manual in order
that you fully understand all the operational features it offers.
Read all the safety instructions carefully before use and keep this
instruction manual for future reference
SAFETY WARNINGS
READ ALL INSTRUCTIONS BEFORE ATTEMPTING TO OPERATE THIS UNIT. KEEP THE ASSEMBLY INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THE ASSEMBLY INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THE ORIGINAL PACKAGING FOR USE WHEN STORING THE HEATER DURING EXTENDED PERIODS OF NON-USE.
-
Read all instructions before using this heater.
-
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handle when moving the unit. Keep flammable materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front and top of the heater and keep them away from the sides and rear of the heater. Keep the rear grille away from walls or drapes so as not to block the air intake.
-
Extreme caution and supervision is necessary when any heater is used near children or invalids and whenever the heater is left operating and unattended.
-
Always unplug heater when not in use.
-
Do not use any heater with a damaged cord or plug or after the heater malfunctions or has been dropped or damaged in any manner. Discard heater or return to an authorized service facility for examination and/or repair.
-
Do not use outdoors.
-
This heater is not intended for use in bathrooms, laundry areas or other similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
-
o not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic areas and place it where it will not be tripped over.
-
o disconnect heater, turn controls to off, then remove plug from outlet.
-
This appliance has a polarized plug (one blade is wider than the other). This plug is intended to fit a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, consult a qualified electrician. Do not connect the heater to extension cords, surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same outlet. Risk of fire, overheat, malfunction, property damage, injury, or even death may result if not adhered to!
-
Connect to properly polarized outlets only.
-
Do not insert or allow foreign objects to enter ventilation or exhaust openings, as this may cause an electric shock or fire, or damage the heater.
-
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
-
A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
-
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, injury to persons or other damage to property.
-
This heater must be plugged into a 120V, 15 amp (or more) circuit of its own. Nothing else can be plugged into the same circuit. If unsure if you home meets this specification, consult a certified electrician prior to use. Risk of fire, overheat, malfunction, property damage, injury, or even death may result if not adhered to!
-
To prevent overload and blown fuses, be sure that no other appliance is plugged into the same outlet or into another outlet wired into the same circuit.
-
It is normal for the heater’s plug and cord to feel warm to the touch. A plug or cord that becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical outlet. Worn outlets or receptacles should be replaced prior to further use of the heater. Plugging heater into a worn
outlet/receptacle may result in overheating of the power cord or fire. -
Ensure the heater is on a stable, secure surface to eliminate the potential of tipping over.
-
Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet /power strip).
-
Be sure that the plug is fully inserted into appropriate receptacle. Please remember that receptacles also deteriorate due to aging and continuous use: check periodically for signs of overheating or deformations evidenced by the plug. Do not use the receptacle and CALL your electrician.
-
Check that neither the appliance nor the power cable has been damaged in any way during transportation.
-
Make sure that no pieces of polystyrene or other packaging material have been left between elements of the appliance. It may be necessary to pass over the appliance with a vacuum cleaner.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
OVERHEAT SAFETY FEATURE
Your heater is fitted with a safe device that switches off the heater in the
event of overheating.
If the heater stops working, turn the heater off and inspect the blockage of
inlet or outlet. Disconnect the plug and wait at least 10 minutes for the
protection system to reset before attempting to restart the heater. If the
safe device still switches the heater off and makes the heater fail to
operate, take the heater to your nearest service center for examination or
repair.
Attention: before restarting the heater, the plug must be disconnected for at least 10 minutes.
SPECIFICATION
| Model | Voltage | Frequency | Power |
|---|---|---|---|
| KPT- 1605F | 120V | 60Hz | 1500W |
OPERATION INSTRUCTION
- On/Off switch
- Oscillation switch
- Temperature adjustment
- Switch on/off the flames effect
- Heating switch ( low power /high power)
- Timer switch ( 0-12H)
The device can be operated either via the controls on the device or by means of the remote control.
- Always place the device with clear space above it and on all sides on a dry, flat, solid and heat-resistant surface out of the reach of children and animals.
- Insert the mains plug into a properly installed socket that is easily accessible.
- On the back of the advice, Move the On / Off switch to the ON position.
- To switch on oscillation, press the button (2). To switch it off, press the button once more.
- To change the temperature, press the button (3) .The device automatically stops heating as soon as the preset temperature has been reached. When the device cools the heating process will be resumed, for as long as the device is switched on.
- To switch on the flames effect, press the button (4). To switch it off, press the button once more.
- To switch the heating , press the button(5), press the button one time is for low power, press the button 6. To switch on the flames effect, press the button (4). To switch it off, press the button once more.
- To switch the heating , press the button(5), press the button one time is for low power, press the button
CLEANING
- Always disconnect the appliance from the main supply before cleaning.
- Clean the outside of the heater by wiping with a damp or dry cloth.
- Do not use petroleum, any other detergent or chemical solvent to clean the heater.
- When the heater is not used for a long time, it should be protected from dust and stored in a clean dry place.
CONTACT INFORMATION
Contact Weave Support
- Need service or support?
- Start your request by Emailing Us.
- AND we will find you a Solution.
- HelloWeaveGaming@Gmail.com