UniLook Smart PTZ Battery Camera User Manual
- June 9, 2024
- UniLook
Table of Contents
Smart PTZ Battery Camera
Easy lnstallatton &Easy Operation
User Manual
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)this device may not cause harmful
interference.
(2)this device must acceptany interference received, including interference
that may cause undesired operation. Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, this equipment
should be installed and operated with minimum distance between 20cm the
radiator your body:
Use only the supplied antenna.
Packing list
- Camera*1
- Bracket*1
- Mounting kit1
- USB charging cable *1
- Operation instruction*1
- Screw for bracket1
- Solar Charger1
Product appearance
| 
---|---
Quick start
The smart battery camera supports battery-powered supply and AC-powered supply
-
Download and install the App
The wireless smart battery camera supports Android and iOSApp
Method 1 Download ‘VicoHome’ APP from APP Store(iOS) or Google Play (Android).
Method 2: Scan APP QR code to download it.
For your best experience, please scan the QR code below with your mobile phone, install the app, and follow the instruction to complete the user registration.
Scan QR code or go to the link to download and install the App. https://www.vicohome.io/download/ -
Add the device
Sign in to the App connect to Wi-Fi and add the device according to the prompts (please bring the device close to the router when configuring).
Set up the camera
- Click the “Add Camera Now” in the App and enter the Wi-Fi network name and password that you want the camera to connect.
To ensure a longer distance connection, the camera only supports the 2.4Ghz
Wi-Fi with stronger wall penetration capability and does not support Wi-Fi for
enterprise
level authentication currently. Please ensure that the entered Wi-Fi meets the
requirements. After completion, click “Continue” to generate the QR code for
pairing the camera
-
After pressing the camera switch for 3 seconds, the camera will turn on. The camera will emit the scanning sound “Ding Dong Ding Dong” after itis turned on (if you do not hear it, please double click the power button).
-
Take the lens of the camera facing the QR code generated on VicoHome about 20 cm (7 inches) until you hear a “Ding” sound
When you hear the “Wi-Fi Password Error”, please check whether the Wi-Fi
password you entered in the App is correct; When you hear the “Wi-Fi Password
Error”. please check
When you hear the “Authentication error” please ensure that your Wi-Fi network
is not an enterprise-level network, and the device supports only the network
with the ecurity level below WPA-2.
- When you hear the “Wi-Fi not found”, please check whether you select or enter the correct Wi-Fi name, and place the device near the Wi-Fi router and ensure that the router is powered on. Please note that 5Ghz Wi-Fi cannot be sear -ched by the device,
- When you hear the “Retrieving IP timeout”, it indicates that the number of devices connected to the router in your home is too many to connect more devices. Please remove some of the connected devices that are not commonly used or restart the router to clear the unconnected devices. You may need to contact the router administrator;
- When you hear the “Cloud service connection fail” please check whether your router is connected properly to the external network. When you hear this error prompt, it is common on the condition of network disconnection or that the selected router in your home is a local area network server Please ensure that the network conne ction is normal, and try to temporarily turn off the firewall to connect again.
Install the camera
You can place the camera on a shelf or other surfaces to use. or you can install it on a wall to use.If the camera is installed indoors, there is no need to install a solar charging panel.
- Select a good spot for your camera
Select a good spot for your camera, please install the camera in a position where its view is not blocked and ensure that it is within the coverage of the Wi-Fi network. The PIR infrared sensor is more sensitive to movements across the camera’s field of view than movements toward or away from the camera.
For outdoor use, please install the camera upside down to maximize the
waterproof performance and the human body infrared sensor’s effectivity
Camera Installation Angle
When installing the camera, it is not suggested to have the PIR sensor
vertically face the moving object, otherwise it may not detect the motion
events. It is suggested to make the angle between the PIR sensor and detected
object greater than 10 degrees
(2)1nstall the bracket
-
Screw fixing:
Fix the camera to the desired location. You can directly place the camera on a flat surface or fix the bracket to the wall or ceiling by screws.
-
Fix the camera
Put the camera up side down and then fix the camera to the bracket by a screw. -
Connect the solar charger to the camera
Open the rubber plug on the back of the camera, then insert the cable of the solar charger to the Micro USB port of the camera. The silicon surface of solor charger is flat with camera surface.
1. What could affect the efficiency of the solar panel?
Your solar panel may not be able to keep your camera fully charged on days
that are snowy, cloudy, foggy or rainy.or during periods of extensive use
(frequent
access to constant triggers). External factors, such as shade, temperature,
weather, and amount of dust or debris on its surface, may also affect the
solar panel efficiency in generating electricity
2. How to optimize the efficiency of solar panel?
For optimizing the effectiveness of your solar panel, you may mount your solar
panel in well-lit places and avoid locations like the shadows of trees,
buildings, or other obstacles to ensure sufficient sunlight. Adjust the
direction of your solar panel to face true south (in the northern hemisphere
)or the true north (in the southern hemisphere) and Pan-Tilt to the
appropriate angle according to your latitude to ensure maximum sun
exposure.Wipe the surface of the solar panel with a wet tissue or cloth
regularly to remove the dust and debris on the panel’s surface
Share the camera
When you want to let other family members or friends view the camera, you can
use this feature Only the admin user who is the first to add the camera is
able to share the camera and manage the settings for the camera. The shared
users have limited access rights.
(1) Steps for Ad min User
-
Find the camera you want to share on the App Homepage. then tap the “Share” button You can also tap the camera “Camera Setting” icon, then tap the “Share” button,
-
Tap “Camera sharing”, a QR code for sharing will be generated
2) Steps for Shared User
For the family members or friends you want to share, find “Add friend’s
camera” on the Homepage to enter the scan code page then scan QR code
generared on the admin’s phone, then send the access request to the admin user
- Steps for Admin User
You will receive a confirmation notice, and you can complete sharing after agreeing
Charge the camera
The App will remind you to charge your camera when the battery is low. Please use the Micro USB cable to plug into the 5//1 5A charging adapter to charge the camera. During charging, the camera’s indicator light is solid yellow, and when the camera is fully charged the indicator light will turn into solid green It will take 15 hours to fully charge the camera
Indicator light status
| Mode | Status |
|---|---|
| Working mode | Blue |
| Sleep mode | Off |
| Charging mode | Yellow |
| Fully charged mode | Green |
Firmware upgrade
When you connect your camera through the App, it will prompt you if the latest
firmware is available You can also manually check the firmware version in the
settings of the App.
Please make sure that your camera is fully charged or connected to the power
adapter before upgrading the firmware, please do not cut off thepower supply
during the upgrading
FAQ
Q:Camera permission management: How to invite family and friends to use my cameratogether?
– A: Open the App and select your camera on the home page. Click the share button on the home page or the “Share in the camera settings to enter the sharing page, and then click “Invite” to generate a QR code. Your friends can now get some of the access rights by scanning the QR code in your phone.
Q:Why doesn’t the Wi-Fi name appear when I connect to Wi-Fi?
– A: On Apple devices with i0S13 and above, you need to turn on the “location permission” for the app in the system settings and change it to “allow when using”.
Q:Will the camera show red lights when night vision is activated?
-A: The built-in infrared lamp beads make the camera only show some dim red lights when night vision is activated, but the image quality is still clear under no light environment.
Q:What are the requirements for Wi-Fi?
– A: Please use a 2.4GHz wireless network. The device does not support the 5GHz wireless network. Meanwhile, please set the Wi-Fi authentication method to WPA2-PSK or other lower level of security method. A password is required.
Q:How far should the camera be placed from the router?
– A: After testing, the Wi-Fi connection distance can normally reach up tot 50 meters in the open area. However, the actual situation depends on the strength of Wi-Fi and its surrounding environment (thick walls, electromag-netic devices, large metal objects will all cause interference to the Wi-Fi signals). If the camera connection signal is weak or unstable, please place the camera as close to the router as possible.
Q:What is the maximum length of recording time?
– A: If you set the duration as ‘Auto”, when someone occurs in the view of the camera, it will start recording a video for up to 3 minutes.
Q:How to quickly view videos by category?
– A: Click the icon in the upper left corner of the “Library” page to start filtering videos by category. Select the category you want to see and then click “Save” to view the video playbacks.
Q:What should I do when the device is in malfunction?
– A: Long press the power button for 3 seconds to restart it. If there is no response, you can remove the rubber plug at the button of the camera. Press the reboot hole with a pointed object to restart the camera.
Thank you for choosing Unilook Battery Powered security
camera! If you have any ouestions about our products and
service ,Please do not hesitate to contact us :
: support@anpvizsecurity.com
: www.anpvizsecurity.com
https://www.vicohome.io/download/
Made in China