X-FAN RDH8025B2 High Quality and Durable Axial Fan Instruction Manual
- June 4, 2024
- X-FAN
Table of Contents
X-FAN RDH8025B2 High Quality and Durable Axial Fan Instruction Manual
Operating Manual for Fans
- SAFETY REGULATIONS AND INFORMATION
Read the operating manual carefully before commencing work at the product. Pay attention to the following warnings to avoid risk to persons or malfunctioning. This operating manual is an integral part of the product. In the event of resale or change of ownership the operating manual must accompany the product. This operating manual may be copied and provided as information on potential risks and their avoidance.
1.1 Hazard classification of warning notices
The following risk ratings are used in this operating manual to denote
potential risk situations and important safety instructions:
DANGER : This is a potentially dangerous situation and warns of an impending
health risk or risk of fatal injury if this warning is not observed. Observe
this warning.
WARNING : The dangerous situation can occur and can result in major or fatal injuries if the warning is not observed. Work with extreme care.
CAUTION : The dangerous situation can occur and can result in minor injuries or damage to property if the warning is not observed.
NOTE : A potentially dangerous situation can occur and results in damage to property if not avoided.
1.2 Qualification of personnel
Only skilled electricians are permitted to install the product, to carry
out the test run and to work at the electrical unit. Only instructed and
authorized skilled personnel are permitted to transport, unpack, operate and
service the product.
1.3 Basic safety regulations
Safety risks related to the product must be reassessed after installing in
the final device. The operating manual was developed in accordance with
European market requirements and may need adapting to the market requirements
of the country in question.
Do not make any changes to the product.
WARNING: Impermissible high load
Stop the product immediately after impermissible loading (e.g. impact, heat,
overvoltage).
ADDITIONAL FOR AC-FANS
CAUTTION: In the event of a fault, the product is energized.
Product has a basic insulation. Do not touch the product after installing.
1.4 Electrical voltage and current
DANGER: Electrical voltage
Regularly check the electrical equipment of the product. Eliminate
immediately loose connections and defective cables.
1.5 Safety and protective functions
DANGER: Missing safety device and faulty protective equipment.
Without protective equipment severe injuries can occur, e.g. by taking hold
of the rotating equipment. Operate the product with protection guards only.
1.6 Electromagnetic radiation
Electromagnetic compatibility (EMC) may affect the system integration of
the product due to interaction. Ensure the electromagnetic compatibility of
the entire system.
1.7 Moving parts
DANGER: Self-starting product
If voltage is applied, the motor automatically restarts after a mains
failure or when blocking has been eliminated. Do not stand in the danger zone
of the product. Switch off the mains voltage when working on the product and
secure against switching on again.
DANGER Rotating impeller:
Contact with the impeller may result in injuries. Long hair, loose-fitting
garments and jewellery can be caught and pulled into the product. Risk of
injury. Before starting the product, ensure that it is securely fixed and that
the guards are in place. Do not wear loose-fitting garments or jewellery when
working on moving parts. Protect long hair by wearing a hair net.
WARNING: Parts transported by the airflow
The product can transport small parts in the airflow and catapult them out.
Ensure that there are no loose small-parts in the intake and exhaust area. Do
not stand in the danger zone of the product.
CAUTION: High risk of fire spreading
Can cause fire to spread. Never direct the airflow (intake/exhaust side) at
a potential source of fire.
1.8 Hot surface
CAUTION High temperature at motor housing. Risk of burns
Provide adequate protection against accidental contact.
1.9 Storage
Store the product in a dry and clean environment that is well protected.
Ensure that the storage temperature is adhered to. If the product is not
operated for a longer period of time, we recommend running it for approx. 15
minutes annually to move the motor bearings.
1.10 Cleaning
NOTE: Product damaged during cleaning
Clean the product carefully with a moist cloth without applying pressure to
the rotor.
Do not use cleaning agents that contain acids, caustic solutions or solvents.
1.11 Disposal
When disposing of the product, observe all requirements and regulations
that are relevant in your country.
- INTENDED USE
The product is designed exclusively as a built-in device for conveying air according to the technical data.
Every use that is not in accordance with the intended purpose, is regarded as misuse of the product. On-site installations must comply with the mechanical, thermal and service life requirements.
2.1 Intended use includes:
– Operating the product with all protective equipment
– Do not put the product into operation before it has been installed in the
customer’s application
– Observation of the operating manual
2.2 Use for other than the intended purpose
Using the product for the purposes mentioned below is prohibited and can be
dangerous
– Conveyance of air that contains abrasive particles.
– Conveyance of air that has a highly corrosive effect.
– Conveyance of air that has a high dust load, e.g. vacuuming sawdust.
– Conveyance of inflammable gases/particles.
– Contact with materials that can damage the product, e.g. acids, caustic
solutions, solvents.
– Exposure to radiation that can damage product components, e.g. strong UV
rays or thermal radiation.
– Operating during external vibration.
– Operating the product close to inflammable materials or components.
– Operating the product in an explosive atmosphere
– Use of the product as a safety component or for performing safetyrelevant
functions.
– Operating in medical devices with life-sustaining or life-saving function,
if not validated.
– Operating in non-stationary systems, e.g. railway vehicles, aircraft and
spacecraft, if not validated.
– Operating with fully or partially dismantled or manipulated protective
equipment.
– Operating the product under conditions other than those mentioned in the
technical data.
– Furthermore, all fields of application not mentioned under intended use.
An in situ assessment must be conducted of the heating behavior (appropriate and inappropriate operation), the protection against contact, electrical shocks, impact of foreign objects or water and the usage at altitudes higher than 2000 meters.
-
TECHNICAL DATA
Drawing, see on the backside of packing. The packing is a part of this operating manual. Therefore do not dispose the packing. -
**CONNECTION AND COMMISSIONING
4.1 Connect mechanical parts
CAUTION: Risk of cutting/squashing when removing the product from the
packaging and during mounting.
**Grap the housing and lift the product carefully out of the packaging. Avoid impact.
NOTE: Risk of damage to electronic components.
Use ESD protective equipment when mounting.
4.2 Connect electrical parts
ADDITIONAL FOR AC-FANS
DANGER: Do not touch. Risk of fatal injury from electrical current
Ensure that the electrical lines are de-energized Secure the operating
voltage against switching on again. Never work on parts that are energized.
Only allow skilled electricians to work on the product
DANGER: Compliance with the electrical installation regulations
Observe the connection regulations that are valid in your country. (e.g.
fusing, GFCI)
CAUTION: Electrical voltage – The product is a builtin component and has no
switch for disconnecting power.
Only connect the product to current circuits that can be switched off by a
switch (all poles disconnected). When working on the product, secure the
system/machine in which the product is installed against switching on again.
NOTE :
Electromagnetic compatibility (EMC) may affect the system integration of the
product due to interaction. Ensure the electromagnetic compatibility of the
entire system.
ADDITIONAL FOR AC-FANS
Ground fault interrupter GFI
Only current-sensitive GFIs (type B) are permissible. Personal protection is
not possible with GFIs when the product is in operation (see also frequency
converters).
4.3 Requirements:
– Before connecting the product, ensure that the supply voltage corresponds
with the product voltage.
– Check whether the data on the nameplate corresponds with the interface data.
– Only use cables that are designed for the current on the nameplate and the
corresponding ambient conditions.
– Ensure that the electrical interface data is adequately protected
(mechanical).
4.4 Check connections
DC-fans ≤ 60V are products of Protection Class lll and must be operated with
safety extra-low voltage.
AC-Fans are products of Protection Class I and must be reliably earthed.
4.5 Connect product
Check the product for visible damage and the operability of protective
equipment before switching on. If damage is visible, do not start the product.
- FAULTS, POSSIBLE CAUSES AND REMEDIES
Replace your product by a new one, do not repair it.
DANGER: Electrical voltage at motor
Wait five minutes after the voltage (all poles) has been switched off
before opening the product.
Technical safety Inspection
- COMPLIANCE
The product bears the CE mark.
The CE mark is affixed to adequately sized nameplates.
Within the meaning of the EMC Guideline 2014/30/EU this document is intended as:
– Mounting instructions/operating manual as per Art. 18, Paragraph (1)
– Installation instructions as per Art. 4 – Operating manual as per Art. 9, Paragraph (3)
– Instructions for use/operating manual as per Art. 18, Paragraph (3)
– Maintenance instructions as per Art.4; Art. 18, Paragraph (1)
Within the meaning of Directive 2014/35/EU -electrical equipment designed
for use within certain voltage limits this document is intended as:
– Instructions for use/operating manual as per Art. 6, Paragraph (7); Art. 8
Paragraph (4)
Within the meaning of the Directive 2006/42/EU Machine Guideline , this
document is intended as
– Mounting instructions as per Art. 13
Errors and Omissions excepted
MOTRAXX ELEKTROGERAETE GmbH
Steinbacher Straße 47-51
90559 Burgthann
Germany
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>