evolur AI-846-02 Toddler Guard Rail Instruction Manual
- June 9, 2024
- evolur
Table of Contents
evolur AI-846-02 Toddler Guard Rail
ASSEMBLY INSTRUCTIONS
- Adult assembly required.
- Small parts may present choking hazard prior to assembly.
- Enclosed please find simple step-by-step instructions to help you quick assemble your product. Before you begin, we recommend that you follow the steps below:
- Please read the instructions thoroughly
- ldentify all parts and hardware
- You may need to provide the following tools:
- Philips Head screw driver
- Flat head screw driver
- ammer
Do Not Use Power Drills Or Drivers
- To protect your parts during assembly please please place them on a soft surface. To clean surface, use only water on a damp cloth.
- Do not use window dleaner or cleaning abrasive as it will scratch the surface and could damage the protective coating.
- Scan the QR code to register your product
- https://www.evolurbaby.com/customer-care/product-registration/
Furniture Care Instructions
Room Climate Control
Wood, when the first cut contains more than 50 percent water. When it is
prepared for furniture construction it is placed in a Kiln and the moisture
content is brought down to 8 to 10 percent. Wood is porous and responds to its
environment. If the room has high humidity it will absorb it and expand and if
the humidity is low it will lose moisture and shrink. It is important that the
humidity levels in the room be controlled from extremes of too much humidity
or too little. Furniture should not be placed close to air-conditioning
outlets, fire places, radiators, space heaters, humidifiers or dehumidifiers.
Exposure to extreme variations of temperature and humidity can damage any fine
wood product.
The Ideal Environment for Fine Furniture
Fine wood furniture will have fewer problems when its environment is
controlled at a temperature between 65 and 75 degrees and a relative humidity
between 35 and 40 percent. Wood placed in an environment out side of those
limits can and will shrink or expand and may develop some small cracks which
are not material or structural defects.
Sticking Doors and Drawers
With the minor changes in temperature and humidity doors and drawers may swell
and be difficult to open or close. Tolerances have been built into the units
but estreme conditions may still cause sticking. This will adjust back to
normal over time but until it does consider usinga dehumidifier or rub candle
wax or paraffin on the sides that stick.
Avoid Direct Sunlight
Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors
and in some cases darken them. It can also cause crazing or hair line cracks
in the finish. White finishes will yellow naturally over time and exposure to
direct sunlight will hasten this natural process along with some woods
darkening naturally over time; this is mot considered to be a quality defect.
Proper Storage
If you need to put your furniture in storage for any period of time do not
store them in a damp basement or hot dry attic. Allow air movement around the
furniture and do not stack any thing on it.
In General
- Protect furniture surface from hot or extremely cold items.
- Use coasters under hot or cold beverages
- Do not use synthetic fabric under accessories or lamps
- Protect tops from pens, makers and crayons
- Oils from potpourri and other seented items can damage the furniture finish.
- Do not drag items across the surface of the furniture.
- Allow the surface to breath by rotating your accessories and lamps.
- Do not over polish the furniture, do it only two or three times a year.
- Over polishing can distort the natural finish of the product.
- Do not wax the furniture as wax build up can destroy the natural finish of the product
- When moving furniture always lift the unit. Do not push or drag it to avoid damage to legs
- Keep the furniture level so doors and drawers open and close freely.
- Clean with a damp, not wet, cloth. Use only a mild soap. Do not use abrasive cleaners.
HARDWARE AND TOOL DIAGRAM
STEP: 1 REMOVE FOOTBOARD
- The model shown is an example only. Styles may vary.
- STEP: 2 ASSEMBLE THE STABILIZER BAR AND TOP CAPS
- The model shown is an example only. Styles may vary.
- STEP: 3 ASSEMBLE THE GUARD RAIL
- MODEL #836, #831, #8311
- The model shown is an example only. Styles may vary.
Day Bed Conversion
STEP: 4
- Model shown is an example only. Styles may vary.
- STEP: 5
- STEP: 6
- STEP: 7
- STEP: 8
- STEP: 9
Documents / Resources
|
evolur AI-846-02 Toddler Guard
Rail
[pdf] Instruction Manual
AI-846-02 Toddler Guard Rail, AI-846-02, Toddler Guard Rail, Guard Rail
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>