SUNNY SF-RB4876 Magnetic Recumbent Bike User Manual

SUNNY SF-RB4876 Magnetic Recumbent Bike User Manual

IMPORTANT SAFETY INFORMATION

We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained, and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions.

1. Before starting any exercise program, you should consult your physician to determine if you have any medical or physical conditions that could put your health and safety at risk or prevent you from using the equipment properly. Your physician’s advice is essential if you are taking medication that affects your heart rate, blood pressure, or cholesterol level.

2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If you do experience any of these conditions, you should consult your physician before continuing with your exercise program.

3. Keep children and pets away from the equipment. The equipment is designed for adult use only.

4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. To ensure safety, the
   equipment should have at least 2 feet (60 CM) of free space all around it.

5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of the equipment can only be maintained if it is regularly examined for damage and/or wear and tear.

6. Always use the equipment as indicated. If you find any defective components while assembling or checking the equipment, or if you hear any unusual noises coming from the equipment during exercise, discontinue use of the equipment immediately and do not use until the problem has been rectified.

7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become entangled in the equipment.

8. Do not place fingers or objects into the moving parts of the equipment.

9. The maximum weight capacity of this unit is 220 pounds (100KG).

10. This equipment is not suitable for therapeutic use.

11. To avoid bodily injury and/or damage to the product or property, proper lifting and moving are required.

12. Your product is intended for use in cool and dry conditions. You should avoid storage in extreme cold, hot or damp areas as this may lead to corrosion and other related problems.

13. This equipment is designed for indoor and home use only; it is not intended for commercial use.

EXPLODED DRAWING

EXPLODED DRAWING

PARTS LIST

No.| Description| Spec.| Qty.| | No.| Description| Spec.| Qty.
---|---|---|---|---|---|---|---|---
1| Main Frame| | 1| 38| Tension Wire| | 1
2| Front Post| | 1| 39| Spring| | 1
3| Front Handlebar| | 1| 40| Circlip| Φ10| 1
4| Seat Post| | 1| 41| Circlip| Φ8| 1
5| Rear Handlebar| | 1| 42| Circlip| Φ35| 1
6| Front Stabilizer| | 1| 43| Circlip| Φ14| 1
7| Idler Wheel Shaft| | 1| 44| Bearing| | 2
8| Magnetic Board| | 1| 45| Locking Nut – Right| | 1
9| Magnetic Wheel| | 1| 46| Locking Washer| | 1
10| Crank| | 1| 47| Step Gasket| | 1
11| Regulator| | 1| 48| Ribbed Belt| | 1
12| Magnetic Wheel Axle| | 1| 49| Hexagon Bolt| M825| 1
13| Hexagon Nut| | 2| 50| Cross Head Screw| M545| 1
14| Locking Washer| | 1| 51| Cross Head Screw| M615| 4
15| Locking Nut – Left| | 1| 52| Lock Nut| M8| 2
16| Open Face Bearing| | 2| 53| Cap Nut| M8| 4
17| Bearing Housing| | 2| 54| Arc Washer| Φ201.5| 8
18| Left Pedal| | 1| 55| Flat Washer| Φ16Φ81.5| 10
19| Right Pedal| | 1| 56| Cross Head Tapping Screw| ST4.216| 11
20| Belt Wheel| | 1| 57| Cross Head TappingScrew| ST4.219| 2
21| Idler Wheel| | 1| 58| Cross Head Bolt| M865| 4
22| Handlebar Cover| | 1| 59| Hexagon Bolt| M815| 4
23| Tension Control Knob| | 1| 60| Hexagon Bolt| M820| 4
23a| Tension Control Wire| | 1| 61| Hexagon Bolt| M855| 2
24| Computer| | 1| 62| Cross Head Bolt| M860| 1
24a| Computer Wire A| | 1| 63| Hexagon Bolt| M835| 1
24b| Computer Wire B| | 1| 64| Hexagon Bolt| M825| 2
25| End Cap| | 2| 65| Foam Grip| | 2
26| Snap Joint| | 2| 66| Spanner| S13-15-17| 1
27| Left Belt Cover| | 1| 67| Allen Wrench| S6| 1
28| Right Belt Cover| | 1| 68| Rear Stabilizer| | 1
29| Back Cushion| | 1| 69| Sensor Wire 1| | 1
30| Seat| | 1| 70| Sensor Wire 2| | 1
31| End Cap| | 2| 71| Sensor Wire 3| | 1
32| End Cap| Φ38| 2| 72| Sensor Wire 4| | 1
33| Adjustment Knob| Φ58Φ23M10| 1| 73| Foam Grip| | 2
34| End Cap| | 4| 74| Wave Washer| | 1
35| Handle Pulse Sensor| | 2| 75| Crank Cover| | 2
36| End Cap| Φ60| 1| 76| Flat Washer| Φ28Φ10.2*1.0| 1
37| Grommet| | 2| 77| Sensor Wire 5| | 1

Ordering Replacement Parts (U.S. and Canadian Customers only)

Please provide the following information in order for us to accurately identify the part(s) needed:

• The model number (found on cover of manual)
• The product name (found on cover of manual)
• The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front of the manual)
  Please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).

ASSEMBLY INSTRUCTIONS

We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1 877-90SUNNY (877- 907-8669).

STEP 1:

Attach the Front & Rear Stabilizers (No. 6 & No. 68) onto the Main Frame (No.

1. with 4 Cross Head Bolts (No. 58), 4 Arc Washers (No. 54), and 4 Cap Nuts (No. 53). Tighten with the Spanner (No. 66).

STEP 2:

Connect the Sensor Wire 2 (No. 70) with Sensor Wire 1 (No. 69), connect the Sensor Wire 3 (No. 71) with the Sensor Wire 4 (No. 72).
CAUTION : Please make sure the Tension Control Knob (No. 23) is at the highest resistance level (level 8, all the way to the right) before you connect the Tension Wire (No. 38). Connect Tension Control Wire (No. 23a) and Tension Wire (No. 38). Then, pull Tension Control Wire (No. 23a) upward and insert it into the slot of metal bracket on Tension Wire (No. 38). Make sure the metal fitting on Tension Control Wire (No. 23a) is secured in the metal bracket. Attach the Front Post (No. 2) onto the Main Frame (No. 1) using with 4 Hexagon Bolts (No. 59) and 4 Arc Washers (No. 54). Tighten and secure with the Allen Wrench (No. 67).

We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877- 907-8669)

STEP 3:

Remove 4 Cross Head Screws (No. 51) from the back of the Computer (No. 24) using Allen Wrench (No. 67). Connect the Sensor Wire 2 (No. 70) and the Computer Wire B (No. 24b), connect the Sensor Wire 3 (No. 71) and the Computer Wire A (No. 24a). Attach the Computer (No. 24) onto the Front Post (No. 2) with 4 Cross Head Screws (No. 51) that were removed. Tighten with Allen Wrench (No. 67)

STEP 4:

WARNING! Read instructions carefully as improper assembly may cause permanent damage to your bike.

CAUTION: Please make sure the Tension Control Knob (No. 23) is at the highest resistance level (level 8, all the way to the right) before you assemble the Left & Right Pedals (No. 18 & No. 19).

Align the Left Pedal (No. 18) with the left side of the Crank (No. 10) at 90°. Turn the pedal bolt on Left Pedal (No. 18) counterclockwise as tightly as you can with your hand. Then, use Spanner (No. 66) to tighten and secure.

Align the Right Pedal (No. 19) with the right side of the Crank (No. 10) at 90°. Turn the pedal bolt on Right Pedal (No. 19) clockwise as tightly as you can with your hand. Then, use Spanner (No. 66) to tighten and secure.

Attach the Front Handlebar (No. 3) onto the Front Post (No. 2) with 2 Hexagon Bolts (No. 64). Tighten with Allen Wrench (No. 67). Then attach the Handlebar Cover (No. 22) onto Front Handlebar (No. 3)

STEP 5:

Loosen and remove the Adjustment Knob (No. 33), the Flat Washer (No. 76) and the Regulator (No. 11) from the Seat Post (No. 4).

Attach the Seat Post (No. 4) onto the Main Frame (No. 1) with 1 Regulator (No. 11), 1 Adjustment Knob (No. 33) and 1 Flat Washer (No. 76) that were removed. Adjust the Seat Post (No. 4) to the desired position, then secure it in place by tightening the Adjustment Knob (No. 33).

STEP 6:

Attach the Seat (No. 30) onto the Seat Post (No. 4) with 4 Hexagon Bolts (No. 60) and 4 Flat Washers (No. 55). Tighten with Allen Wrench (No. 67).

Attach the Rear Handlebar (No. 5) onto the Seat Post (No. 4) with 2 Flat Washers (No. 55), 1 Hexagon Bolt (No. 63), 1 Cross Head Bolt (No. 62) and 1 Lock Nut (No. 52). Tighten with the Spanner (No. 66) and the Allen Wrench (No. 67).

Attach the Back Cushion (No. 29) onto the Seat Post (No. 4) with 2 Flat Washers (No. 55) and 2 Hexagon Bolts (No. 61). Tighten with the Allen Wrench (No. 67).

Lastly, connect the Sensor Wire 4 (No. 72) to the Sensor Wire 5 (No. 77).
The assembly is complete!

MAINTENANCE & ADJUSTMENT GUIDE

ADJUSTING THE SEAT

Turn the Adjustment Knob (No. 33) counter-clockwise to release Seat Post (No. 4) and then slide the Seat Post (No. 4) forward or backward to the desired position. Secure the Seat Post (No. 4) in place by turning the Adjustment Knob (No. 33) clockwise until tightened.

MOVING THE RECUMBENT BIKE

To move the recumbent bike, hold the Rear Stabilizer (No. 68) and tilt the recumbent bike until the End Caps (No. 31) located on the front stabilizer touch the ground. With the End Caps (No. 31) on the ground, you can transport the recumbent bike to the desired location with ease.

ADJUSTING THE BALANCE

To achieve a smooth and comfortable ride, you must ensure that the recumbent bike is stabled and secured. If you notice the recumbent bike is unbalanced during use, adjust the End Caps (No. 25) located on the Rear Stabilizer (No. 68) until the recumbent bike becomes levelled with the floor surface.

ADJUSTING THE TENSION

Adjust the tension by rotating the Tension Control Knob (No. 23) clockwise to increase the level of resistance. Rotate the Tension Control Knob (No. 23) counter-clockwise to decrease the level of resistance. Tension levels are set at Level 1 being the lowest and Level 8 being the highest.

CLEANING

The recumbent bike can be cleaned with a soft, clean, damp cloth. Do not use abrasives or solvents on plastic parts. Please wipe your perspiration off the recumbent bike after each use. Be careful not get excessive moisture on the computer display panel as this might cause electrical hazards or electronics to fail. Please keep the recumbent bike, especially the computer, out of direct sunlight to prevent screen damage. Please inspect all assembly bolts and pedals on the recumbent bike for proper tightness every week.

STORAGE
Store the recumbent bike in a clean and dry environment, away from children.

BATTERY INSTALLATION AND REPLACEMENT

BATTERY INSTALLATION:

1. Take out 2 AAA batteries from computer box.
2. Press the buckle of battery cover on the back of the Computer (No. 24), then remove battery cover.
3. Install 2 AAA batteries into the battery case on the back of the Computer (No. 24). Pay attention to the battery + and – ends before installing.
4. Press the buckle of battery cover, then put the battery cover back to the back of the Computer (No. 24).

BATTERY REPLACEMENT:

1. Press the buckle of battery cover on the back of the Computer (No. 24), then remove battery cover.
2. Remove the 2 old AAA batteries in the battery case and install 2 new AAA batteries into the battery case on the back of the Computer (No. 24). Pay attention to the battery + and – ends before installing.
3. Press the buckle of battery cover, then put the battery cover back to the back of the Computer (No. 24).

NOTE: Always change both batteries at the same time. Do not mix battery types and do not mix old and new batteries. Dispose batteries according to your state and regional guidelines.

EXERCISE COMPUTER

FUNCTION BUTTONS:

MODE: Press the button to select TIME, DISTANCE, AND CAL to preset. Press the button for selection function display value on LCD or enter after setting. Press the button and hold for 3 seconds to reset all values except odometer to zero. (When user replaces the batteries, all the values will reset to ZERO automatically.)
SET: To set up the target value of TIME, DISTANCE, and CAL. Press the button and hold for 2 seconds to speed up the increment. RESET: Press the button to reset function value when setting. Press the button and hold for 3 seconds to reset all values except odometer to zero. (When user replaces the batteries, all the values will reset to ZERO automatically.)

FUNCTIONS & OPERATIONS:

1. BATTERY INSTALLATION:
   Please install 2 AAA 1.5V batteries in the battery case on the back of computer. (Whenever batteries are removed, all the function values will be reset to zero.)

2. AUTO ON/OFF:
   Once the user begins to exercise, the computer will show the workout value automatically. After about 4 minutes of inactivity, the computer will turn off. Odometer value does not reset to 0 when the computer turns off. When the user starts to exercise again, the workout value of odometer will accumulate continuously.

3. AUTO SCAN:
   After the computer is powered on, press Mode button and the LCD will display all function values from TIME-SPEED-DISTANCE-CALORIES-ODOMETER PULSE. Each value will be shown for 6 seconds.

4. SPEED:
   Displays the current training speed from 0.0 to 99.9 MPH (miles per hour).

5. DISTANCE:
   Accumulates total distance from 0.00 up to 9999 M (miles). The user may preset target distance by pressing the SET & MODE button. Each increment is 0.1 M (miles). Automatically counts down from targeting value during exercise.

6. TIME:
   Accumulates total time from 00:00 up to 99:59. The user may preset target time by pressing SET & MODE button. Each increment is 1 minute. Automatically counts down from targeting value during exercise.

7. CALORIES:
   Accumulates calories burned during training from 0.0 to 9999 (Cal). The user may also preset the target calories before training by pressing SET & MODE button. Each setting increase is 1 Cal. Automatically counts down from targeting value during exercise.
   NOTE: This data is a rough guide which cannot be used in medical treatment.

8. ODOMETER:
   Displays the total accumulated distance from 0 to 9999 M (miles). User can also press MODE button to display the odometer value.

9. PULSE:
   The computer will display user’s heart rate in beats per minute (BPM) during training.

10. RESET:
    Press the button and hold for 2 seconds to reset all values except odometer to zero.

NOTE:

1. If the computer display is abnormal, please re-install the new batteries and try again. Always change both batteries at the same time. Do not mix battery types and do not mix old and new batteries.
2. Battery Spec: 1.5V UM-4 or AAA (2PCS).
3. Dispose the batteries safely, according to your state and regional guidelines.

TROUBLESHOOTING

computer and verify that the wire from the computer is properly connected to the wire that comes from the front post.2.    Check if the batteries are correctly positioned and battery springs are in proper contact with batteries.3.    The batteries in the computer may be unresponsive. Change tonew batteries.
The       recumbent              bikewobbles when in use.| Turn the end caps on the rear stabilizer as needed to level therecumbent bike.
The       recumbent                  bike makes                  squeaking noisewhen in use.| The bolts may have become loose on the recumbent bike. Please inspect all the bolts and tighten any loose bolts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>