ARMYTEK Wizard C2 WR Magnet USB Red and White Light User Manual

ARMYTEK Wizard C2 WR Magnet USB Red and White Light

Thank you for choosing the products of Armytek. Please read this manual carefully before using the flashlight.

Specifications

Headlamp: simple one-hand operation, reliable headmount. Solid body without long wires, weak rubber connectors and unnecessary boxes. The flashlight is easily installed, removed and 180° rotatable in the mount. Quick-release rubber ring provides additional fixation

Every Day Carry light: compact design, convenient side button, spe-cial matt anti-abrasive finish without rough knurling, strong built-in tail magnet and robust removable steel clip

Bicycle light: body made from durable and lightweight aircraft-grade aluminium, improved shock resistance, new springs for better bat-tery and driver protection. Constant light without flickering, optional quick-release mount. Red light for use as bicycle rear light

• 4 LEDs: amazing beam of red light up to 230 lumens and white light up to 1100 lumens thanks to 2 LEDs for each color

• Red light is almost invisible for animals, fish and insects, comfortable for night vision

• 5 brightness modes for each color, easy operation with one button and double click for switching between white and red light

• Convenient wide beam of fully upgraded optical system, TIR-lense is protected from scratches by tempered glass with anti-reflective coating

• Innovative technology allows using any 18650 Li-Ion batteries and provides full protection against short circuit even in case of contact between magnetic connector and metal objects

• Active real-time temperature control to prevent overheating above
  + 58 °C and warning indication of low battery level

• Total protection from water, dirt and dust in accordance with IP68 standard — flashlight continues to work even at 10 meters depth. Withstands fallings from up to 10 meters

• Robust and water resistant magnetic connector

Set description

• Flashlight, 18650 Li-Ion 3200 mAh battery, magnetic USB charger, clip, headmount, 2 spare O-rings, user manual.
• The producer reserves the right to change the package at his own discretion without modifying this manual. Specifications are sub-ject to change without notice.

Light output for flashlights with Warm light is about 7% less, beam distance is about 3% less. All the above specifications are test results based on ANSI/NEMA FL1-2009 Standard. The tests are performed using the battery included in the set. The data may vary due to environment, heat dissipation and other factors.

Initial Service

TO SET/REPLACE BATTERY

1. Unscrew the tailcap.
2. Place the battery with the positive contact (+) facing the head of the flashlight.
3. Adjust the tailcap and tighten it as far as it can go.

The flashlight is ready for operation.

HOW TO CONNECT THE MAGNETIC CHARGER

Unscrew the tailcap to 1/4 of a circle and adjust the magnetic charger to the tailcap.

CHARGER COLOR INDICATION
Charger not plugged in:

• Green device is in waiting mode.
• Green blinking evaluation of battery voltage.
• Red blinking unscrew the tailcap to 1/4 for charging.
• Orange blinking  USB power source voltage is too low for correct continuation of charging or bad contact between charger and battery. Clean the tailcap and the threads of the flashlight parts, use a diffe-rent power source.
• Red charging with rated charging current is going on.
• Orange  USB power source voltage is too low, charging current may be reduced.
• Green charging is finished.

Operation

• Before use: Tighten the tailcap as far as it can go.

In OFF state

1 click: To turn on the last used mode.
Press and hold: To turn on Firefly mode of the last used light. Keeping button pressed will start cycling through modes of the chosen light. Release to select.
In ON state:

1. click: To turn off the flashlight.
   Press and hold: To start cycling through modes of the chosen light. Release to select.

2. clicks: To change between white and red light in any mode.
   Add/Remove Strobe modes. Unscrew the tailcap to 1/4 while the flashlight is off, press the button, tighten the tailcap while keeping the button pressed and then unscrew it again.

• Automemorizing: After switching off the last used mode is memorized for quick access at next switching on.

• Active temperature control: When the temperature of the flashlight becomes close to +58 °С, brightness decreases to safe value, allowing the flashlight to avoid overheating for a long period of time. In condi-tions of good air-cooling the flashlight delivers light without stepping down.

• Low battery level: When the brightness is approximately <25% from the nominal value, the LED will flash 2 times. If you are not sure wheth-er or not it flashed, switch the flashlight
  off and on: in case the battery is low, the flashes will repeat after 30 sec from switching on. At critical level light output decreases to Firefly mode.

• Lock-out function: Unscrew the tailcap to 1/4 for the protection from accidental switching on.

Warnings
For effective operation of the flashlight we recommend branded 18650 Li-Ion batteries without PCB (unprotected) no more than 70 mm long. The flashlight can get hot in Turbo and Strobe modes quickly and discharge the battery with high current. Don’t leave it without your attention as very bright light might heat objects and cause fire. It is forbidden to charge the battery inside the flashlight when the ambient temperature is below 0 °C.

1. Always follow the instructions from this manual and recommenda-tions on battery usage.
2. Apply only the recommended power sources.
3. Do not reverse battery polarity.
4. Do not modify or recast the flashlight and its components as it will deprive you of the warranty.
5. Do not allow water or any other liquid to leak into the flashlight.
6. Do not aim a switched-on flashlight at people’s or animals’ eyes – it can cause temporary blindness.
7. Do not allow children to use the flashlight without your assistance.

The producer will not be liable for any harm done to the user if it was caused by improper use of the product.

Care and Storage

It is recommended to clean the threads and O-rings off dirt and old grease once or twice per year. Remember that reliable protection from water and dust cannot be provided by worn out sealing. The fouling as well as lack of lubricant cause fast wear-out of threads and sealing rings.

To clean the threads do the following:

1. Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).
2. Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged replace it by a new one.
3. Clean the metal threads with a brush using ethanol. Be careful not to  allow the applied liquid to get inside the flashlight or tailcap as it can cause fails in functionality of the flashlight.

After cleaning lubricate the thread and the sealing ring with polyal- phaolefin-based silica grease, e.g. Nyogel 760G. The application of other types of grease is unacceptable. In case of active operation and exploitation in dusty environments, it is recommended to perform cleaning and lubricating of the parts as often as required.

WE DO NOT RECOMMEND to leave power sources inside the flash-light for a long storage period, as batteries (especially non-recharge-able) can leak for various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in, previously install new and high-quality batteries, store the flashlight in acceptable for batteries operational temperature and revise the batteries’ state at least once a month. If you have noticed any signs of defects, withdraw the batteries from the flashlight and dispose of them.

Warranty and Service

Armytek provides free warranty repairs for 10 years (excluding bat-teries, chargers, switches and connectors, which have 2-year warran-ty) from the date of purchase if there is a document confirming the purchase. The warranty does not extend to damage during:

1. Improper usage.
2. Attempts to modify or repair the flashlight by nonqualified specialists.
3. Application in chlorinated, contaminated liquids or sea water.
4. Immersion into liquids in case of broken leakproofness.
5. Exposure to high temperatures and chemicals, including the liquids from defected batteries.
6. Usage of low-quality batteries.

Armytek
Germany, 10551 Berlin, Jonasstraße 6
+1 206-785-9574, service@armytek.com
www.armytek.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>