QAZQA 102706 Modern Vifte Ceiling Fan Instruction Manual

102706 Modern Vifte Ceiling Fan
Instruction Manual

Vifte Fan
102706/102707
CCT dim(3500-2700-3000K) with night light function

Ceiling fan lamp incl. LED QL7001019
3300lm Module
1600lm Lamp
32W LED Module
72W Lamp
220-240V–50Hz
3500-2700-3000K (with night light function)
CRI>80
17000h
8500 ON/OFF

FittinQ B.V.
Smaragdweg 52, 5527 LB Hapert, The Netherlands
www.qazqa.nl
102706/102707
32W LED
incl. LED Board: QL7001019
220-240V~50Hz

This product contains a light source of energy efficiency class F

https://eprel.ec.europa.eu/qr/770559
102706
8718881111440

Replaceable (LED only) light source by a professional.

Replaceable control gear by a professional.

Warning symbols

| Read the instructions
Caution
Lamp
---|---

General Safety Instructions

Read this instruction manual thoroughly before using the appliance and save it for future reference and if necessary pass the instruction manual on to a third party.
WARNING: When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and personal injury.

General

• Before carrying out any work on the fan, disconnect it from the electrical supply!

• Check if the electrical specifications of this appliance are compatible with your installation. The supplier accepts no responsibility for any physical injury or material damage resulting from incorrect use or installation of this fan.
  If you have the slightest doubt, please contact the electrician.

• Unauthorized use and technical modifications to the appliance can lead to danger to life and health.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision

• Children should be supervised to ensure that they do not play with the appliance.

• This appliance is for indoor use only.

• Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

• Never install the appliance in a moist or wet room.

• Be careful when working near the rotating blades. The fan should be installed at least a height of 2.3m

• Before pushing the reversible slide switch, it is necessary to stop the action of the blades by turning off the fan

• Don’t place your arm or another object in the path of the blades, when the fan is operating.

• Always maintain the minimum distance between the lamp and any inflammable material (SF (curtains, wall, etc), as indicated on the pictogram

• This means for all poles disconnection having a contact separation that provide full disconnection under over-voltage category III conditions must be incorporated in the fixed wiring in accordance with national wiring rules.

• Power supply wire from the ceiling needs 1.5 sq mm wire

• Regarding the method of the cable connection, how to assembly and the bulb type reference of a luminaire, thanks to refer to the section “INSTALLATION”

• Warning: Before obtaining access to terminals, all supply circuits must be disconnected.
  “5. Appliance specification”.

• Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

Electrical safety
The appliance should be installed by an authorized electrician only acc. to national wiring rules.
Specific Safety Rules
The fan is to be installed so that the blades are more than 2.3 m above the floor
Environmental protection CAUTION!
Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection service.

Appliance specifications

Rated voltage
Rated frequency| 50 Hz
Rated wattage| 40 W
Bulb rating| 1x3OW. LED
Ambient operating temperature| 25 °C
Protection dass| I
P number| IPO
Protective shields| N / A

The ceiling fan (element)

PARTS DESCRIPTION

Installation of the ceiling fan

1. Insert the down rod over the upper canopy, then insert the cross pin over the yoke & Cotter pin and fasten the screws which fix the down rod(Fig 1)
2. Install the mounting plate with screws (Fig.2)
3. Loose the screw from the motor.(Fig 3)
4. Install the blade on the motor with Screws.(Fig.4)
5. Make sure the fan is disconnected from the electrical supply and carefully insert the fan into the Mounting bracket. Rotate the fan until the notch of the hanger ball engages the pin of the mounting bracket. Then, firmly fix the screws.(Fig5)
6. Assemble the LED light plate to the light kit fixing bracket by the screws and connect the LED light kit by male & female plugs. Insert the remote control receiver on the mounting bracket. Connect the motor wires, LED light wires, and receiver’s power wires to the receiver by male & female plugs. Also, connect the ground wire with male &  female plugs. Then connect the power supply to the fan. (Fig6)
7. Assembly the shade to the light plate and assembly of the upper canopy to the mounting bracket. Both rotate clockwise when assembling.(Fig 7)
8. Now, the fan is completed. (Fig 8)

How to use

• Direction switch on the fan‘s remote.(FORWARD and REVERSE switch)
• Down for summer make the air move directly from the ceiling.
• UP for winter, to circulate the warm air generated by the heater to the floor.

Remote Control Instruction

This ceiling fan can be installed with remote control, but make sure you know how to install the device in a safe way or consult a licensed electrician
Warranty may be affected if you install the improper remote control or install it in an improper way.
WIRING SCHEMATIC DIAGRAM FOR RECEIVER

Adopt RF wireless digit emission technique, biunique controlled, coincident code rate is less than one millionth.(Emitter and receiver must be sent back to the factory for  maintenance if damaged.)
The receiver can be controlled by any angle of the emitter in prescriptive space, unrestricted by direction. With the memory function, the controller can save the status( light and direction ) while the supply power is OFF and resume to the original after reloading the power supply.

FUNCTION INSTRUCTION OF EMITTER

1. DON/OFF the fan
2. ON/OFF the light
3. Speed of the fan ((1)low speed —-(5)high speed)
4. The direction of the fan (reverse switch)
5. Timing control of the fan
6. LED indicated light
7. 12V battery should be used in the emitter

Notes:

1. Power on, the light on with 3500K
2. Push the LIGHT ON/OFF button the 1st time, and the light off
3. Push the LIGHT ON/OFF button the 2nd time, and the light on with 2700K
4. Push the LIGHT ON/OFF button the 3rd time, and the light off
5. Push the LIGHT ON/OFF button the 4th time, and the light on with 3000K.
6. Push the LIGHT ON/OFF button the 5th time, and the light off
7. Push the LIGHT ON/OFF button the 6th time, and the light on with the night light function.

(3) KINDLY REMINDERS:

1. Learning code matching mode is used between the emitter and receiver. Turn “ON” the supply power within 30 seconds and press the emitter’s “FAN ON/OFF” button for 5  seconds, it can load normally after hearing the long sound “bee”， which means learning successfully and it can work normally. (PS: Learning mode is not accepted after  turn “ON” the supply power for 30 seconds)

2. When the emitter cannot control the receiver, please check whether the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.

3. When the emitter cannot control the receiver, please check if is there any existence of similar remote-controlled products nearby, then check whether they work, because a remote-controlled product with the same frequency will disturb each other.

4. The low voltage of the battery will affect the sensitivity of the emitter and the signal reception accordingly (the indicated light will flash out its warning when the battery get low voltage), must replace if the battery is getting low voltage.

5. Please take out the battery from the emitter when leaving it unused for a long time.

6. The maximum load of lighting sees the above
   POWER PARAMETER LIST”
   PS： please connect the ground wire correctly, otherwise it may cause the light micro-light or flash

7. When installing the fan, the fan ceiling cover doesn’t press the antenna(or other wire), it is easy to break down the wire and short-circuited.

Disconnect from mains before maintenance or cleaning.

Do not use a wet sponge to clean the appliance.

1. Before conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it cools down
2. No abrasive products, solvents, detergent, or any other liquid may be used to clean the fan or lamp
3. Be sure the power is off when you clean the fan
4. Don’t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit

Troubleshooting

B/ Loose power line
connections to the fan. C/ Speed controller not in the correct position.| A/ Check main and branch circuit fuses or circuit
breakers.
B/ Check line wire connections to the fan
C/ Check the speed controller’s position.
2. Fan sounds noisy| A/ Top canopy touching the ceiling.
B/ Loose fan blade screws. C/ Ceiling fan not secured against the ceiling.
D/ Incorrect speed controller.| A/ Lower Canopy from ceiling to ensure minimum 3 mm clearance.
IV Re-tighten all screws on fan
blades but never over-tighten.
C/ Re-tighten all screws in the hanging bracket or plate.
D/ Change the controller to the one supplied.
3. Mechanical Noise| A/ Allow at least 8 hours settling-in period.|
4. Fan Wobbles| A/ Fan blades are not horizontal to the ceiling.
B/ Blade screws are loose.| A/ Measure from the ceiling to tip of blades, then rotate fan so all blades are checked for equal height from the ceiling (not
adjustments may be made by slight pressure up or down on blade holders). Make sure all screws are securely fastened.

DYNAMIC BLADE BALANCE KIT

PREFACE

Your ceiling fan may sometimes have wobble problems when operating due to irregularity in the blades or the blade holder. Also, improper assembly in the mounting system
may cause some additional problems also bearing crooked. The following procedure to remedy such a problem is strongly recommended by us from our past experience in
handling the wobble problem.
Dynamic blade balancing kit for ceiling fans

1. Make sure that all blades are firmly screwed into the blade holder
2. Make sure that all blades are firmly secured on the flywheel and check the pitch of blade holders all must be the same
3. By looking up the fan from below, check and be certain that none of the blade holders are bent so that none of the blades is out of position. A correction can be made by  very gently bending the blade holder back into position
4. By the simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and even with the outside leading edge of a  blade. Note the distance of the edges of the blade to t he ceiling; carefully turn the blade slowly by hand to check the remaining blades. If blade is not in alignment, the  blade holder may be gently bent up or down to be in line with the other blades

If by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing kit. Follow the procedure listed below:

• Turn the fan on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.

• Turn the fan off; select on the blade and place the balancing clip on it. Halfway between the blade holder and the blade up on the rear edge of the blade.

• Turn the fan on, and watch to see if the wobble is improved or worse. Then, turn the fan off again and move the clip to another blade, and test again. Repeat this process
  with all blades and then note that blade which is the most improved.

• Move the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this blade and operate the fan to find the position
  where the clip gives the most improvement

• Next, remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.

Caution: stay clear of the blades if the clip for any reason is not secured, the injury could result in 12) Others
Have your product repaired by a qualified person
This electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise,
this may result in considerable danger to the user. This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction
concerning the use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older
than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
Please contact the store which you bought the product for after-sale services if question
This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning the use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.

Information requirements regarding the eco-design

Description| Symbol| Value| Unit
Maximum fan flow rate| F| 64.| ms/min
Fan power input| P| 43.50| W
Service value| SV| 1.| /mg/min//W
Standby power consumption| PS9| 0.0| W
Seasonal electricity consumption| Q| 14.| kWh/o
Fan sound power level| [WA| 43.50| dB/AI
Maximum air velocity| c| 1.| m/seg
| Regulation N° 206/2012
| IEC 60879:1986
| EN 50564:2011
Measurement standard for service| EN 607042-7:1998
| EN 607041:2010
| [Shall not appear all of these ones, but the same as the ones which are
| detailed in the ERP test report]

SAFETY INSTRUCTION

Please study the instruction manual and below information carefully before installing or using this product.
Please keep this user manual for further reference

1. The luminaires may only be installed by authorized and qualified technicians according to the valid regulations for electrical installation.
2. Maintenance of the luminaires is limited to their surfaces. During maintenance, no moisture can come into contact with any areas of the terminal connections or voltage control parts.
3. The electrical supply must be switched off at the outset, preferably by means of a switch in the distribution box, before any installation, maintenance, or repair work is undertaken.
4. Exterior lighting must not be installed during rain.
5. Take account of the minimum separation distance from other objects and the room required around the fitting.
6. If in any doubt, consult a professional, toking locol installation requirements info account. Some countries stipulate that lighting may be installed only by registered installers.
7. Clamping screws in electrical connections must be adequately tightened. This is particularly the case with 12V low-voltage conductors.
8. Cleon with o clean, dry cloth or brush, use no solvents or abrasives. Avoid dampness on all electrical components
9. Take account of all available technical information.
10. Meaning of symbols:

| For indoor use only, where direct contact with water is impossible
This icon indicates the level of water-proof and dust-proof I Protection Closs I: the fitting must be earthed] Protection Closs II: the fitting is doubled insulated and does not require earthing
Protection Closs Ill: the fitting is low voltage
Minimum distance from lighted objects (meters)
The type of lamp and maximum size and wattage indicated in each lighting unit must not be exceeded; different items require different kinds of light sources with different bulb icons re armature is designed to work only with the indicated voltage. Different items require different working voltages.
The luminaire can be used in combination with a dimmer
The reference light angle and light space of the luminaire cannot be disposed of together with normal domestic  waste in standard rubbish can, but you have to bring it to a staging area for electrical waste
---|---

Take note of the symbols when connecting wires:

FittinQ B.V
Smaragdweg 52, 5527 LB Hapent, The Netherlands
www.qozqo.nl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>