DN15 Hydrus Ultrasonic Hot Water Meter Installation Guide
- June 9, 2024
- HYDRUS
Table of Contents
Installation guide
HYDRUS
DN15 Hydrus Ultrasonic Hot Water Meter
HYDRUS
The data generated by the meter can be viewed in the display loop with system
information (e.g. flow rate, volume, date, due date, medium tem- perature).
The loops are numbered from 01 to 09.
The optical button located on the front panel enables scrolling the display
loops.
To save battery lifetime, the meter switches automatically to power save mode
after 4 minutes of inactivity. The display is awakened again by pressing the
optical button.
After awakening, the display shows first a screen check (i.e. all symbols in
the display are briefly switched on and off) and then the total volume.
This remains for at least 10 seconds on the display (also when the optical
button is pressed). Afterwards the display loop can be switched with the help
of the optical button.
Display loop
| 88 | Displaytest | 5 | Error / Alarms |
|---|---|---|---|
| 1 | Total volume | 7 | High resolution total volume |
| 2 | Battery lifetime | 8 | Due date / Due date volume |
| 3 | Firmware version / Checksum | 9 | Reverse volume |
| 4 | Current flow |
| 1 | Conformity label | 10 | Protection class |
|---|---|---|---|
| 2 | Year of the declaration of con- formity | 11 | Temperature class |
| 3 | Type of examinaiton certificate number | 12 | Product article number |
| 4 | Meter serial number & QR code | 13 | Communication interfaces |
| 5 | Optical button | 14 | Battery lifetime |
| Ho | Positioning assistance for opto head | 15 | Dynamic range |
| 7 | Pressure loss class | 16 | Nominal diameter |
| 8 | Maximum admissible pressure | 17 | Permanent flow rate |
| 9 | Metrological class | 18 | Type |
Pulse outputs (open drain)
| Input voltage | max. 30 V |
|---|---|
| Input current | max. 27 mA |
| Voltage drop at the active output | max. 2 V / 27 mA |
| Current through inactive output | max. 5 pA / 30 V |
| Reverse current | max. 27 mA |
| Pulse duration, pulse break, pulse frequency | depending on device |
configuration (detailed description on request)
Wiring diagram
The pulse outputs are open-drain circuits.
The drain branch has a resistance of just 0 ohm, i.e. there is no internal
current limiting. If required, this must be provided by an external protec-
tive resistance (*if not available on site).
The internal resistance of the switching device must be 5x of the protec- tive
resistance.
Cable pin assignment
The Radio/L-Bus/Pulse, Pulse/Pulse and M-Bus/Pulse/Pulse versions of the meter
are supplied with a 1.5 m 2/3/4/5-wire connecting cable with wire end
ferrules.
| Radio/ L-Bust Pulse| Pulse/ Pulse| M-Bus/ Pulse/ Pulse| M-Bus| 4-Wire Pulse
---|---|---|---|---|---
M-Bus| | | x| x|
Pulse, Output 1| | x| x| | x
Pulse, Output 2| x| x| x| | x
L-Bus| x| | | |
Connection (network name)
| GND | brown | brown | brown | brown | |
|---|---|---|---|---|---|
| Pulse 1 or L-Bus | yellow | yellow | yellow | white | |
| Pulse 2 | green | green | green | yellow | |
| M-Bus 1 | white | white | |||
| M-Bus 2 | blue | blue | |||
| Manipulation / Tampering | green | ||||
| Niimhpr of Wirec | 2 | 2 | 5 | 2 | 4 |
**** Never connect the external M-Bus to the pulse output of the meter! It will destroy the pulse output and lead to the loss of all factory warranty claims.
Radio specifications
Sending intervals| Every 14 … 256 seconds (variable, according to 0.1 duty
cycle (min. 14 seconds); depending on protocol length and programming)
---|---
434 MHz frequency band| Transmission power (EN 300 220-2 V3.2.1): 10 mW e.r.p.
868 MHz frequency band| Transmission power (EN 300 220-2 V3.2.1): 25 mW e.r.p
Venting
In the event that complete venting of the meter is not possible, please
install the meter at an angle of 45°!
Open Source Software Notice
This product contains open source software components.
The use and distribution of any open source software is governed by respective
terms and conditions of the applicable open source license. By using this
product, you acknowledge that you have reviewed such license terms and
notices, and you agree to be obliged by these terms.
Please insure that you get yourself familiar with the licenses terms and
conditions before using this product. The complete license terms are available
in the DIEHL Metering Download-center: https://www.diehl.com/metering/en
/support-center/download-center/
If you have any questions regarding open source software used in this product,
please contact DIEHL Metering support: oss-dmde@diehl.com
EU DECLARATION OF CONFORMITY
Device Type / Product, object of the declaration
| Type | Technology | No of the EU type examination certificate |
|---|
This declaration of conformity is issued under the sole responsibility of the manufacturer. The object of the declaration described above is in conformity with the relevant Union harmonisation legislation, insofar as it is applied:
| 2011/65/EU (OJ L 174, 1.7.2011) | RoHS Directive |
|---|---|
| 2014/30/EU (OJ L 96, 29.3.2014) | Electromagnetic Compatibility Directive |
| 2014/32/EU (OJ L 96, 29.3.2014) | Measuring Instruments Directive |
| 2014/53/EU (OJ L 153, 22.5.2014) | Radio Equipment Directive |
In conformity with the following relevant harmonised standards or normative documents or other technical specifications:
EN 62368-1:2014/AC:2015
EN 62479:2010
EN 300 220-1 v3.1.1
EN 300 220-2 v3.1.1
EN 300 330 v2.1.1
EN 301 489-1 v2.2.3
EN 301 489-3 v2.1.1| EN 62368-1:2014/AC:2015
EN 62479:2010
EN 300 220-1 v3.1.1
EN 300 220-2 v3.1.1
EN 300 330 v2.1.1
EN 301 489-1 v2.2.3
EN 301 489-3 v2.1.1| EN 301 489-3 v2.1.2
EN 301 489-52 v1.1.0
EN 301 908-1 v13.1.1
EN 301 908-13 v13.1.1
WELMEC 7.2:2018
EN IEC 63000:2018
---|---|---
Name and address of the manufacturer| The notified body LNE n° 0071 has
carried out the module D certification of quality assurance under number:
---|---
DIEHL METERING Donaustraße 120 90451 Nürnberg
GERMANY| LNE-36769
The contact address marked on the product can be one of the site listed in the
module D certificate.
Nürnberg, 2022-05-02
EU DECLARATION OF CONFORMITY
Device Type / Product, object of the declaration
| Type | Technology | No of the EU type examination certificate |
|---|---|---|
| 174 | Ultrasonic Water Meter | DE-19-MI001-PTB011 (NB 0102, PTB) |
T819958N-01-TEC (NB 0682, CTC)
This declaration of conformity is issued under the sole responsibility of the manufacturer. The object of the declaration described above is in conformity with the relevant Union harmonisation legislation, insofar as it is applied:
| 2011/65/EU (OJ L 174, 1.7.2011) | RoHS Directive |
|---|---|
| 2014/30/EU (OJ L 96, 29.3.2014) | Electromagnetic Compatibility Directive |
| 2014/32/EU (OJ L 96, 29.3.2014) | Measuring Instruments Directive |
| 2014/53/EU (OJ L 153, 22.5.2014) | Radio Equipment Directive |
In conformity with the following relevant harmonised standards or normative documents or other technical specifications:
EN 55032:2015/A11:2020
EN ISO 4064-1:2017
EN ISO 4064-2:2017
EN ISO 4064-3:2014
EN ISO 4064-5:2017
OIML R49-1:2006
OIML R49-2:2004| EN 62368-1:2014/AC:2015
EN 62479:2010
EN 300 220-1 v3.1.1
EN 300 220-2 v3.1.1
EN 300 330 v2.1.1
EN 301 489-1 v2.2.3
EN 301 489-3 v2.1.1| EN 301 489-3 v2.1.2
EN 301 489-52 v1.1.0
EN 301 908-1 v13.1.1
EN 301 908-13 v13.1.1
WELMEC 7.2:2018
EN IEC 63000:2018
---|---|---
Name and address of the manufacturer| The notified body LNE n° 0071 has
carried out the module D certification of quality assurance under number:
---|---
DIEHL METERING Donaustraße 120 90451 Nürnberg
GERMANY| LNE-36769
The contact address marked on the product can be one of the site listed in the
module D certificate.
Nürnberg, 2022-05-02
EU DECLARATION OF CONFORMITY
Device Type / Product, object of the declaration
| Type | Technology | No of the EU type examination certificate |
|---|---|---|
| 174 | Ultrasonic Water Meter | DE-19-MI001-PTB011 (NB 0102, PTB) |
T819958N-01-TEC (NB 0682, CTC)
This declaration of conformity is issued under the sole responsibility of the manufacturer. The object of the declaration described above is in conformity with the relevant Union harmonisation legislation, insofar as it is applied:
| 2011/65/EU (OJ L 174, 1.7.2011) | RoHS Directive |
|---|---|
| 2014/30/EU (OJ L 96, 29.3.2014) | Electromagnetic Compatibility Directive |
| 2014/32/EU (OJ L 96, 29.3.2014) | Measuring Instruments Directive |
| 2014/53/EU (OJ L 153, 22.5.2014) | Radio Equipment Directive |
In conformity with the following relevant harmonised standards or normative documents or other technical specifications:
Name and address of the manufacturer| The notified body LNE n° 0071 has
carried out the module D certification of quality assurance under number:
---|---
DIEHL METERING Donaustraße 120 90451 Nürnberg
GERMANY| LNE-36769
The contact address marked on the product can be one of the site listed in the
module D certificate.
Nürnberg, 2022-05-02
UK Declaration of Conformity
-
Instrument model/instrument:
Hydrus Type 173 -
Name and address of the manufacturer:
Diehl Metering
Donaustrasse 120
90451 Nürnberg
Germany -
This declaration of conformity is issued under the sole responsibility of the manufacturer.
-
Object of the declaration:
Ultrasonic Water Meter HYDRUS -
The object of the declaration described above is in conformity with the relevant UK statutory requirements:
2016 No. 1091 The Electromagnetic Compatibility Regulations 2016 with Amendments
2016 No. 1153 The Measuring Instruments Regulations 2016 with Amendments
2017 No. 1206 The Radio Equipment Regulations 2017 with Amendments
2012 No. 3032 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 with Amendments -
References to the relevant designated standards or normative documents used or references to the other technical specifications in relation to which conformity is declared:
EN 55032:2015/A11:2020
EN 14154-1:2005/A2:2011
EN 14154-2:2005/A2:2011
EN 14154-3:2005/A2:2011
EN ISO 4064-1:2017
EN ISO 4064-2:2017| EN ISO 4064-3:2014
EN ISO 4064-5:2017
OIML R49-1:2006
OIML R49-2:2004
EN 62479:2010
EN 62311:2008| EN 301 489-1 v2.1.1
EN 301 489-3 v2.1.1
EN 300 220-2 v3.1.1
EN 62368-1:2014/AC:2015
EN IEC 63000:2018
---|---|--- -
The approved body NMO, Approved Body number 0126, performed type examination and issued the type examination certificate UK/0126/0326.
The approved body NMi Certin UK (TIC) Ltd., Approved Body number 8506, performed quality assurance of the production process and issued the certificate: UKCA-397
Signed for and on behalf of:
Nürnberg, 2022-08-31
UK Declaration of Conformity
-
Instrument model/instrument:
Hydrus Type 174 -
Name and address of the manufacturer:
Diehl Metering
Donaustrasse 120
90451 Nürnberg
Germany -
This declaration of conformity is issued under the sole responsibility of the manufacturer.
-
Object of the declaration:
Ultrasonic Water Meter HYDRUS -
The object of the declaration described above is in conformity with the relevant UK statutory requirements:
2016 No. 1091| The Electromagnetic Compatibility Regulations 2016 with Amendments
---|---
2016 No. 1153| The Measuring Instruments Regulations 2016 with Amendments
2017 No. 1206| The Radio Equipment Regulations 2017 with Amendments
2012 No. 3032| The Restriction of the Use of Certain Hazardous Substances in Electrical and Electrical and Electronic Equipment Regulations 2012 with Amendments -
References to the relevant designated standards or normative documents used or references to the other technical specifications in relation to which conformity is declared:
EN 55032:2015/A11:2020
EN 14154-1:2005/A2:2011
EN 14154-2:2005/A2:2011
EN 14154-3:2005/A2:2011
EN ISO 4064-1:2017
EN ISO 4064-2:2017| EN ISO 4064-3:2014
EN ISO 4064-5:2017
OIML R49-1:2006
OIML R49-2:2004
EN 62479:2010
EN 62311:2008| EN 301 489-1 v2.1.1
EN 301 489-3 v2.1.1
EN 300 220-2 v3.1.1
EN 62368-1:2014/AC:2015
EN IEC 63000:2018
---|---|--- -
The approved body NMO, Approved Body number 0126, performed type examination and issued the type examination certificate UK/0126/0326.
The approved body NMi Certin UK (TIC) Ltd., Approved Body number 8506, performed quality assurance of the production process and issued the certificate: UKCA-397
Signed for and on behalf of:
Nürnberg, 2022-08-31
Diehl Metering GmbH
Industriestrasse 13 91522 Ansbach
Phone: +49 981 1806-0
Fax: +49 981 1806-615
info-dmde@diehl.com
https://www.diehl.com/metering
Mat.-Nr. 3089479 • 19/9/2022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>