Huizhou Ojd Technology OJD-88 3 In 1 Wireless Charger User Manual
- June 9, 2024
- Huizhou Ojd Technology
Table of Contents
Huizhou Ojd Technology OJD-88 3 In 1 Wireless Charger
User Manual
Product Introduction
Thank you for purchasing this product! This product is a 3-in-1 Wireless Charger with a simple and generous design, suitable for mobile phones, headsets, iWatch and other Qi wireless charging devices. Provide you with a convenient, fast, safe and free wireless charging experience.
Product Appearance
Instruction
- Plug in the equipped Type-c cable and turn on the power.
- Stand the bracket up and place the device supporting Qi standard in the center of the charging area to start charging.
Indicator Status
LED Indicator
|
State
---|---
Blue & green light turns off after 2s| Power connected
Blue light| Phone Charging
Green light| Earphone Charging
Blue light/green light flashes| Metal object detected or abnormal charging
Product Parameters
Product name: 3IN I WIRELESS CHARGER
Model: 0.JD-97
Input: 9V/2A 12V/1.5A
Phone output: 5W/7.5W,10W/15W
Earphone output: 3W(max,
Watch output: 3W(max’
Product Size: 12373135mm
Product size Fold: 152’73’28mm
Accessory List
3IN I WIRELESS CHARGER’I
Im Type-c Cable’l
User Manual’1
Matters Needing Attention
- Please use a qualified fast charging power adapter, otherwise it may cause unstable charging
- Do not put metal debris or magnetic card on the product, it may cause damage to the product or abnormal charging,
- Please use the device as it is designed for and kindly follow the safety instructions, or it would be of your own responsibility for any damage caused
Safety Instructions
- Do not pull the power supply hard, to avoid the power cord break or fall off.
- Do not disassemble the product or put it into fire or water to avoid short circuit and leakage
- Do not use the product in severe high temperature, humidity or corrosive environment, to avoid damage to the circuit and leakage phenomenon
FAQ
The phone does not charge.
– A:The phone is not aimed at the charging sensing area or the receiving coil is not installed correctly.
Charging fever.
– A: It is normal for the receiving coil or transmitter to generate heat during wireless charging.
Mobile phone charging intermittently.
– A:The charging current of the power adapter is insufficient or the voltage
is unstable, please use a qualified fast charging adapter.
– A: The charging position is too biased, the electromagnetic induction is not
in place, and the charging position needs to be adjusted.
Slow charging.
– A:The wireless charging current allowed by the mobile phone itself or the external receiving coil is different, or the standby power consumption of the mobile phone is large when charging, it is recommended to reduce the standby program of the mobile phone.
Other questions.
A: Please contact after-sales customer service directly.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two cond itions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation. Caution: Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. NOTE: This equipment
has been tested and found to comply with the limits for a Class B digital d
evice, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable prote ction against harmful interference in a residential
installation. This equipment generates uses and c an radiate radio frequency
energy and, if not installed and used in accordance with the instructions ,
may cause harmful interference to radio communications. However, there is no
guarantee that int erference will not occur in a particular installation. If
this equipment does cause harmful interferen ce to radio or television
reception, which can be determined by turning the equipment off and on, t he
user is encouraged to try to correct the interference by one or more of the
following measures: – Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement
Radiation Exposure Statement The equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment.
During the operation of device a distance of 15 cm surrounding the device and
20 cm above the top surface of the device must be respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>