Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable User Manual

June 2, 2024
Outsolidep

Outsolidep Logo LQ320 54 Inch Phone Tripod Stand Extendable
User Manual
Outsolidep LQ320 54 Inch Phone Tripod Stand
Extendable

LQ320 54 Inch Phone Tripod Stand Extendable

Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable -
Overview

Remote Shutter Instructions

Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable - Remote
Shutter

STEP 1: Paring
STEP 2: Turn on camera
STEP 3: Shooting

  1. Turn on the power button(located at the side of remote), indicator LED flashes and “AB Shutter3” will enter into pairing mode.
  2. Turn on your phone Bluetooth and search for “AB Shutter 3” device
  3. Select the device of “AB Shutter 3” from the list and pairing will be finished automatically in few seconds.

Parameter
Model: LQ320
Material: Aluminium alloy and ABS
Folded length: 16.5 in
Maximum height: 54 in
Loading capacity: 4.4 lbs

Photography tripod introduction

Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable - Photography
tripod

Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable - Figure
1

1. Panorama Shot: Rotate the Pan Locking Knob counter-clockwise and move the handle for smooth 360 panorama Shot.| 2. The platform plate usage: loosen the verticall lock knob to reach the 90 degree of the platform.
Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable - Figure
2
3. Open the lock catch and take off the quick release plate Aim the device at the 1/4 screw on the quick release plate, tighten the buckle under the quick release plate to fix the device on the quick release plate.
After installing the device, put the quick-release plate back into the card slot and lock it.| 4. Pitch angle adjust: Rotate the handle counter-clockwise and tilt the Pan head,
allow maximum 90° for vertical use. Clockwise rotate the handle to lock.
Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable - Figure
3
5.Adjust the tripod leg up and down, fix the tripod leg by rotating the screw clockwise (counterclockwise loosened).| 6. Extending the legs: Flip open the leg lock lever and gently pull on the leg segment to the desired length.

Cellphone Assemble Instruction

Phone holder can be adjusted between 2.3-3.75 inch, compatible with most smartphones within this width range.

Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable - Cellphone
Assemble

  1. Take out the tripod and phone holder
  2. Open the lock catch and take off the quick release plate
  3. Tighten the buckle under the quick release plate to fix the phone holder
  4. Put the quick release plate with the phone clip installed back into the card slot and lock it.
  5. Mount your phone into Phone holder
  6. Adjust the tripod to the desired angle and enjoy your shooting

Outsolidep LQ320 54 Inch Phone Tripod Stand Extendable - Cellphone Assemble
1

Notice:

  1. When you receive this product, please check that everything is complete.
  2. Completely unfold the tripod when using it, make sure every lock knob is fixed and locked, avoid accidental damage to mobile phones and other electronic products.
  3. Do not use a tripod in an unstable place.
  4. When you change the photography scene, you must remove the electronic equipment from the tripod.
  5. Avoid using at temperatures under -22°F or over 158°F.
  6. Please pay attention to cleaning after use, especially after use in wet and sandy places. Not suitable for use in sea water.
  7. The tripod is equipped with a safe load. Do not load equipment that exceeds 4.4 lbs to avoid damage to the stability of the tripod then affect the photographic effect.
  8. The tripod is made of conductive material. For safety, please do not use it in dangerous places such as lightning weather or near the high voltage lines

Package Includes:

  • Tripod&*1
  • Phone Holder*1
  • Remote Control*1
  • Tripod Carry Bag*1
  • User Manual*1

Outsolidep Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals