FINE DIGITAL GX5000 Dash Camera User Manual

DIGITAL GX5000 Dash Camera
User Manual

SAFETY INSTRUCTIONS

Precautions for installation

• Place the external GPS about 20cm (8 inches) or more away from the device.
•  If the distance between the product and the installed DMB antenna or GPS receiver is close, it may cause the reception rate to deteriorate. Place the device 20cm (8 inches) away from OMB antenna and GPS receiver.
• Select an installation location more than 20crn away from other electronic devices like a navigation device.
• Do not install the device at the location where it obstructs the drryer’s view.
• Ensure the power cable plug is tightly inserted into the right power inlet on the device.
•  Ensure the device is firmly installed and fixed.
• Make sure the power cable is connected to the cigarette lighter socket or a proper terminal in the fuse box.

Precautions for use

• Finedigital is not responsible for any accident caused by user inattention. Product damage or injuries during the operation.
• Avoid using the device under extreme conditions such as direct sunlight, high temperature and/or high humidity. It may cause damage to the device.
• Even if the product supports the low voltage cutoff function, there is a risk of discharge when the vehicle is parked for a long time.
• Do not use damaged, modified, or unauthorized parts and accessories.
• Use the device within the rated voltage range.
• Do not operate the device while driving.
• Avoid placing the device near flammable and explosive liquids or gases. This may cause explosion or fire.
• Avoid putting metal, flammable or wet objects into the memory card slot or the connectors on the device. This may cause electric shock or fire.
• Do not operate the device with wet hands. It can cause electric shock.
• Do not leave the device or its accessories within reach of children.
• Do not cover the device with a cloth or a blanket while in use. Continuous heating may cause fire or device failure.

* For user’s safety aid to as proem damages, read through this manual and 0 follow the instructions cocrectfr.
Anecigitzd is NOT rmon0b for any orobkms andfor daenrces that may coos from the failure to observe the instoxtions,
*IN THE PACKAGE
Optional Accessories
To improve the performance of the device, the contents of this manual are subject to change without prior notice.
Installing Micro SD Card and External GPS Antenna
Insert the Micro SD card into the slot and push it until it locks into the place.
Install the External GPS Antenna on the upper left or right corner of the windshield.

• **** It is strongly recommended to use FrneVu memory card in order to minimize memory card error.
• Do not apply excessive force on the Micro SD card or attempt to insert it in the wrong direction as it may cause damage to the Micro SO card and the card slot.
•  To prevent loss of important data, please frequent& copy recorded videos from a Micro 50 card to another storage device such as a personal computer for backup.

PRODUCT OVERVIEW
Main Unit(Front Camera)
Rear Camera

INSTALLATION

Front Camera
Rear Camera

• **** Please install the device away from the heat rays of the vehicle,

Key features

STARVIS| With SONY Exmor R STARVISTM image sensor, it provides a more bright and clean image resolution than with ordinary CMOS sensors day and night. And, Auto Night Vision helps to show much clearer image quality in dark alleys and underground parking lots.
---|---
Record High
Resolution Video| Record both the front and rear view in FULL HD (1920x1080p030fps) through a high performance camera sensor and lens.
High Resolution
IPS LCD| With 2.5 times more pixels than the general TN panel LCD, IPS LCD offers clear images and wide viewing angle.
The resolution is 800 x 480, providing a clearer screen than the existing(480×320).
Auto Night Vision| Minimize deterioration of image quality and record a bright image at a place of low illuminance or during night driving and parking.
Power Saving Parking Mode| With FineVu’s unique low-power technology, it safely records even while parked for a long time.
When set as the low power mode, there are restrictions on the use of some services, such as Al Damage Detection 2.0
Smart Time Lapse 1.0| This is an intermittent recording made in which the camera takes photos of motion at a consistent interval and reproduces them at normal speed. It enables you to check recorded videos quickly by setting time lapses in driving and parking mode.
Record video in standard 30fps when an event occurs in driving and parking mode.
Al Damage Detection 2.0| It is an advanced Al algorithm for damage detection which provides shock alarm by subdividing the strength and part of the actual vehicle impact, excluding everyday impacts such as car door opening and closing impact, trunk opening and closing impact, and et
H DR| Clearly record video with FineVu’s tuning technology under various illuminance changes backlight, night driving, entrance/exit of tunnels, parking lots and, etc.
ADAS| The ADAS (Advanced Driver Assistance System) supports functions like the front vehic’e motion alert (FVMA) and lane departure warning system (LOWS) (ft operates when GV signals are received).
Speed Camera Alert| Provide voice guidance on seven hoes of traffic enforcement camera such as speed came red light camera and traffic sensor camera.
This feature may not be supported depending on the country.

• **** Even when LCD turns off for safe driving (set screen timeout time to 1 minute), if shock alarm, ADAS notification, and speed camera alert notification occur, the LCD turns on temporarily to inform the situation.

SPECIFICATION

Dimension /
Weight| Front : 98.5 x 64.8 x 31.04mm / 107.59 Rear : 53.4 x 30.3 x 41.5mm / 26.5g| Excluding cables and mounting bracket
Memory Capacity| Micro SD Card (32GB / 6466 / 128GB)| Class 10 or above recommended / SDXC compatible
Recording mode| Driving recording| lrnin. Interval recording
Driving event (impact) recording| 20 sec. recording
(10 seconds before and after detection)
Manual recording| 20 sec. recording
(10 seconds before and after detection)
Parking (impact & motion detection) recording| 20 sec. recording
(10 seconds before and after detection)
Driving time lapse recording| 30fps recording after impact detected
Parking time lapse recording| 30fps recording after impact detected
Lens| Front : Full HO wide-angle lens Rear : Full HD wide-angle lens|
Image Sensor| Front : 2.13M pixels, 14.8″ SONY Exmor R STARVIS mage Sensor Rear : 2M pixels, 1/3′ CMOS Image Sensor
Viewing Angle| Front: more than 145° of the opposite angle / 11 5° of the horizontal angle / 62° of the vertical angle
Rear : more than 134° of the opposite angle / 105° of the horizontal angle / 60° of the vertical angle
Video| Front : 1920X1080$190fps Rear : 1920X1080p0030fps|
Display| 3.5° IPS LCD (800 x 480) with Touch|
Microphone| Built-in|
Speaker| Built-in|
Acceleration
sensor| 3-axis acceleration sensor| +2g / -2g
Input power| DC 12V – 24V|
Battery| Super capacitor| Supply power to safely store video recording in case of external power shutoff
Power
consumption| 4.1W| Based on 2ch, LCD Off, GPS Off
Operation / Storage temperature| Operation temperature -10t – 60t 1 Storage temperature -20t- 70t|
Interface| Power port (3.50), Rear Camera Connection Port (2.50), External GPS Port (2.543)| Vehicle speed, ADAS and Speed Camera Alert operate under GPS reception

SCREEN LAYOUT
Live view and Menu screens

1. FineVu settings| Aspect Ratio(Standard/Front Zoom/Rear Zoom/Full Zoom), Rear Camera Display(Standard /Flip Horizontal), HDR(ON/OFF), Installation Angle Guide, Speed Unit(km/h / mph).
---|---
2. ADAS| Lane Departure Warning System, Front Vehicle Motion Alert, Speed Camera, ADAS Speaker, ADAS Settings.
3. Memory Settings| Memory Partition Information, Memory Partition(Drive Priority/Event/Parking), Memory Format.
4.  Recording Settings| Driving Recording Method(Standard/Smart Time Lapse), Parking Recording Method(Motion/ Smart Time Lapse/Power Saving), Sensitivity Settings(Driving Event/Parking Event/Front Camera Parking Motion/Rear Camera Parking Motion), Low Voltage Settings, Cut-off Time Settings.
5.  Playback| Playback the recorded video of each recording mode.
6. System Settings| LCD(OFF/Screen saver/Always ON), LCD Brightness(Auto/Dark/Mid/Bright), Show Menus(OFF/ON),
Front Camera Security LED(OFF/ON), Date and Time Setting, Menu Lock(OFF/ON)
7.  Setting information| Display the current setting values.
8. Live view| Display live view.
9. AI Damaae Detection 2.0| Display Al Damaae Detection 2.0

• **** When you change dashcam settings. the memory card may be reset. In that case, a POMO shuns to co the screen. Please read 4 carefully.
• VehKle speed. AOAS. Speed Camera Alert operate under GPS reception.
• Do not operate the device while drrang
•  When map Menu settnigs, the recording will be *sabred.
•  Front Vehicle Motion Alert will be notified n 3 seconds after the departure of front vehicle.
• When usng the vehcle’s ISGOche Stop & Go) function. it is recommended to change the Low Voltage Setting of the black box to ‘bland

ADAS Settings

• Before using ADM features, settings must be calibrated on calibration settings are required [Menu ADAS  ADAS Settings].
• Align the green line with the horizon, and align the red line with center of the bonnet by pressing the left/right arrows.
• Then, align the orange line with the front edge of the bonnet with the up/down arrows.
• Press live button to start recording.
  

Memory Settings

• Sets how storage space on the memory card will be allocated for each recording mode.

1. Memory partition information
2. Parking event
3. Driving
4. Memory format
5. Driving Event
6. Memory settings
7. Parking motion
   

Item| Driving| Driving Event| Parking Motion| Parking Event| Total
---|---|---|---|---|---
Driving Priority| 70| 10| 15| 5| 100
Event Priority| 45| 20| 20| 15| 100
Parking Priority| 40| 10| 45| 5| 100

• **** Parking modeoperatesore/Innen the hardwiring Power Catae is ccnnected. The hardwiring Power Cable
• must be professionally installed to the vehicle by a trained mechanic
• Using cables from other manufacture* may damage the product or result in fire or electric shod due to the  different voltage.
• Use genune nnedrotal accessories.
• Use constant pone during parking raordng and the power should be annected separately except some velicle htes. In this case. please ask for help from an installation soeciaist fusing regular power isrecommended to prevent battery discharge of the vehicle.)
• When connecting a hardwire power cable. please be careful about connecting locatC0 of each wire.
• DO not Cut or modify the dedicated cable yowself.

Driving mode

Driving recording| •After the product is completely booted up, the driving recording mode starts.
•During driving, videos are recorded in 1 minute segments and stored in the “normal” folder in the memory card.
---|---
Driving time lapse recording| •Change the smart time lapse settings in [Menu Recording Settings Driving Recording Smart Time Lapse].
•The recorded videos are stored in the “normal” folder in the memory card. (Audio recording will be disabled.)
Event (impact) recording| •When an impact is detected in driving recording mode, the event detection recording mode starts.
•A video is recorded for 20 seconds, from the moment 10 seconds before detection to 10 seconds after detection, and stored in the “event” folder in the memory card.
Event (impact) recording in
driving time lapse recording mode| •When an impact is detected in driving time lapse recording mode, the event detection recording
mode starts.
•A video is recorded for 20 seconds, from the moment 10 seconds before detection to 10 seconds after detection, and stored in the “event” folder in the memory card.
•The recorded video is automatically recorded and stored at a rate of 30fps, not time lapse.
Manual recording| •When you press ‘Manual recording button’, it turns red and the manual recording mode starts.
•A video is recorded for 20 seconds, from the moment 10 seconds before pressing the button
and to 10 seconds after pressing the button, and stored in the “camcorder” folder in the memory card.

Parking mode

Switching to Parking Mode| •If you turn off the vehicle with regular power connected, the parking recording mode starts.
•If you turn on the vehicle, the driving recording mode starts again.
---|---
Parking mode (Impact detected)| •When an impact is detected during parking, the event detection recording mode starts.
A video is recorded for 20 seconds, from the moment 10 seconds before detection to 10 seconds
•after detection, and stored in the “parking” folder in the memory card.
Parking mode (Motion| •When motion is detected in parking recording mode, the event detection recording mode starts.
•A video is recorded for 20 seconds, from the moment 10 seconds before detection to 10 seconds
after detection, and stored in the “motion” folder in the memory card.
Parking time lapse recording| •Change the smart time lapse setting in [Menu – Recording Settings Parking Recording Smart Time Lapse].
•The recorded videos are stored in the “motion” folder in the memory card.
*Continue to record video in time lapse regardless of motion detection.
Event (impact) recording in
parking time lapse recording mode| •When an impact is detected in parking time lapse recording mode, the event detection recordingm mode starts.
•A video is recorded for 20 seconds, from the moment 10 seconds before detection to 10 seconds
after detection, and stored in the “parking” folder in the memory card.
•The recorded video is automatically recorded and stored at a rate of 30fps, not time lapse.
Recording Modes| Driving (Driving Time Lapse)| Driving Event| Parking Event| Parking Motion
(Parking Time Lapse)| Manual| My Folder
---|---|---|---|---|---|---
Folder Name| normal| event| parking| motion| camcorder| my folder

• Entire Micro SD Card yell be formatted vMen the memory partibOn Settings 6 changed.
• t16 recommended to bark to data before <banging memory partition settn9S.
• Memory format type is FAT32. If the format *different. the device MI autcmabraly start memory format.
• if select ‘Orrin® only. the device writ mord on dine more only and pamkmg recording veil be cl6abled. When the engine 6 turned off, the device van abo be turned off.

Playing video
On live view screen, tap (Menu—Replay).
The recorded videos are categorized and displayed by the recording mode.
Select a recording mode, and tap the video you want to play.

1. Video category| The video files are categorized by the recording mode – Driving, Event, Parking event,
Parking motion, Camcorder, My folder(View folder/Save video).
*Al Damage Detection 2.0 videos are stored in “parking” folder.
---|---
2. Video list| Display the video from the latest file.|
3. Video list pages| : Move backward 3 pages
: Move forward 3 pages| : Move backward 1 page
Move forward 1 page
4.  Playback screen| Playback the selected video file. (Tap the screen to hide or re-display the function buttons.)
5. Switch front/wrear view| 1 ch : Play video of front camera| 2ch : Play video of rear camera
6.  Play button| : Play the previous/ next file.| : Rewinds the current : Plays the recorded file/ file by 5 seconds temporarily pauses playback
7. Previous menu| Move to the previous menu screen.|

• Please operate the deice after stopping your vehicle in a safe location.
• While you playback the video Hess eve deice will stop recordirq.
• Flay videos en the playback menu of the device or a computer onb. If you play videos by imertarg the memory card in devices such as a smartohone or a tablet PC, the video recordings may be lost
• During playback, vehide tense numbers may not be identified due to the relative sceed of a vehicle or fight conditions.
• A fie name is composed of the recording start date and time, and the recording mode.
• If the memory card reached full capacity. the previously recorded videos are deleted for the sufficiency of storagego prevent data loss, balk up imccrtant videos on adcfitional storage devices.)

FineVu PC PLAYER
FineVu Player is software that you can play the videos recorded by the FineVu dashcam. You can download it at the FineVu website(http://www.FineVu.com/en).
Main Screen
After the installation is complete, run the FineVu player. The following provides brief information about the PC players screen layout.

1. Main screen that plays back a recorded video.
2. If GPS data are included in the recorded video, ‘a the location is displayed in the map.
3.  If GPS data are included in the recorded video, we the speed is displayed.
4.  Display G-Sensor values or speeds in a graph.
5. Menu for playing and backing up video and setting wo the player
6.  Menu for analyzing recorded videos
7. Display the video list.

System requirements

• ** The FineVu player supports both Mac and Windows. • Please use the `FineVu player, or the video playback may be limited.
  **

Viewing recorded video on PC

1. Remove the Micro SD card from the device, and insert it into the adapter. Connect the card to the PC using the Micro SD card reader.
2. When the Micro SD card reader is connected to the PC, a USB drive or new disk drive will be created.
3. Click the relevant folder and select video files you want to play back or view.
4. FineVu Player or other players can be used to watch recorded video. (You should use FineVu Player to check the GPS and G-Sensor information of the recorded video.)

Upgrading Firmware

1. Download the latest firmware at FineVu website. (htttp://www.FineVu.com/en)
2.  Remove the Micro SD card. Insert it into Micro SD card reader and connect the reader to the PC.
3. When the reader is connected to the PC, a USB drive or new disk drive will be created. (It’s recommended to format the Micro SD card used for another device before you upgrade the firmware.)
4. Unzip the downloaded file, and copy it to the top-level root of the memory card.
5. Insert the copied Micro SD card into on the device. Turn on the vehicle (ACC On) or start the engine to turn on the device.
6. The firmware update starts automatically.
7. The system will automatically restart once the firmware update is completed.

Tips for using Micro SD card

1. A firmware upgrade is provided to enhance the device’s features, operation or to increase stability. For optimal operation of the device, ensure that you keep the firmware up to dal
2. To prevent loss of important data, frequently copy recorded videos from Micro SD card to other storage devices.
3. The Micro SD card should be tested for errors on a regular basis. And as the memory card is a consumable item, it should be replaced periodically. – The warranty period of memory card is 6 months. – The memory card should be formatted every 2 weeks to maximize the lifetime of the memory card.

• Do not d6connect the power or remove the memcry card from the deice during the firmware upgrade. (Xing so may cause serious damage to the device, or to the data stored in the memory card.
• The firrnsvare must be upgraded on Micro SD card.
• The firmsvare fileswil to deleted automatically after upgrades completed.
• It’s recanmended to bathe imponant Sea files and format the Micro SD card before starting firmware Pgrade.
• tf the Micro SD card is 6468 ct more, change the fie system to FAT32 before formatting the memory card.

7th Floor, Fine Venture Bldg., 41, Seongnam-daero 925 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 13496 Rep. of KOREA
www.finevu.com/en
ICustomer Support [email protected]
Made in Korea

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>