TaiMei MD04 Bathroom Vanity Mirror User Guide
- June 3, 2024
- TaiMei
Table of Contents
TaiMei MD04 Bathroom Vanity Mirror
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Read all instructions before using
DANGER- To reduce the risk of electric shock:
- Always unplug this furnishing from the electrical outlet before cleaning.
- Unplug from outlet before putting on or taking off part.
- Close supervision is necessary when this furnishing is used by, or near children, invalids,or disabled persons.
- Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
- Keep the cord away from heated surfaces.
- Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
- Do not use outdoors.
- Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- To disconnect, turn all controls to the off position, then remove plug from outlet.
- WARNING: Risk of Injury – Keep children away from extended foot support (or other similar parts).
- WARNING: Risk of Electric Shock – Connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
- For loading always put heavier items at the bottom and not near the top in order to help prevent the possibility of the furnishing tipping over.
- WARNING: Risk of Injury to Persons – do not place video equipment such as televisions or computer monitors on the product.
- WARNING: Risk of Injury to Persons – do not use this furnishing to support video equipment such as televisions or computer monitors.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product.
THANK YOU
We can assure you that FOCA has used the best materials and has applied the
strictest quality control measures to ensure that each and every unit meets
the highest quality standards. This booklet contains general information about
the unit as well as step-by-step installation instructions.
BEFORE BEGINNING
- Carefully read the instructions before beginning the installation.
- DANGER! To avoid the risk of electrocution, please turn off the electricity mains before commencing the installation.
- It is strongly recommended that this installation be performed by a professional electrician.
- It is recommended that you wear safety glasses at all times during the installation.
- A minimum of two people are needed to perform this installation
- This product is wall mounted only
MAINTENANCE
Never use scouring powder pads, abrasive material, strong bleach or sharp instruments on metal components or glass. An occasional wiping down with a mild soap diluted in water is all that is needed to keep the mirror and aluminum parts looking new. Test products on a small inconspicuous surface prior to use.
TOOLS AND MATERIALS REQUIRED
HARDWARE LISTING
CAUTION To avoid the risk of electrocution, please turn off the electricity mains before commencing the installation. We recommend the mirrors gets fitted by a qualified electrician.
MIRROR INSTALLATION
First Way
PLACEMENT
Select the desired position of the mirror. Level and mark the location.
SUPPORT LOCATION
Mark the drilling locations ensure marking are leveled.
INSTALL MOUNTING BRACKET
Using a drill, make holes and fill with supplied plugs and install mounting
bracket.
CONNECTING ELECTRICAL WIRING
PLEASE
NOTE: The colors referenced in the diagram above is based on conventional
standards and may differ between households. If there is any confusion as to
how these should be connected, please seek the help of a licensed professional
electrician. Electric shock, fire hazard and death are possible consequences
of poor wiring for none of which FOCA will be held liable.
PLACEMENT
Place the mirror against the wall and slide down as shown in image 2
.
Second Way
PLACEMENT
Select the desired position of the mirror. Level and mark the location
.
SUPPORT LOCATION
Measure the center of the holes and mark the drilling locations ensure
marking are leveled.
INSTALL SCREWS
Using a drill, make holes and fill with supplied plugs and screws. Leave a
gap of 2 – 3mm between the head of the screw and the wall.
CONNECTING ELECTRICAL WIRING
PLEASE NOTE:
The colors referenced in the diagram above is based on conventional standards
and may differ between households. If there is any confusion as to how these
should be connected, please seek the help of a licensed professional
electrician. Electric shock, fire hazard and death are possible consequences
of poor wiring for none of which FOCA will be held liable.
PLACEMENT
Place the mirror against the wall and slide down as shown in image 2
.
User’s Guide
CAUTION Touch button will be functional only after 3 seconds of power-up.
Short Touch
Long Touch
Documents / Resources
|
TaiMei MD04 Bathroom Vanity
Mirror
[pdf] User Guide
MD04 Bathroom Vanity Mirror, MD04, MD04 Vanity Mirror, Bathroom Vanity Mirror,
Vanity Mirror, Bathroom Mirror, Mirror
---|---