COMICA Vimo C 2.4G Dual Channel Mini Wireless Microphone User Manual

COMICA Vimo C 2.4G Dual Channel Mini Wireless Microphone

Foreword

Thanks for purchasing Comica 2.4G Dual-channel Mini Wireless Microphone Vimo C

Features

• Broadcasting-level Sound Quality, Universal for Camera, Phone and Computer
• Digital Signal Processing , Support One-key Noise Reduction
• Support Real-time Audio Monitor, Mono/Stereo/Safety Mode Switch
• 4-level Adjusted Gain Control and One-click Muting
• Rotatable IPS Display for Intuitive Operation and Usage
• Rechargeable Storage Case for Charging, Storing and Power Monitoring
• Duration Up to 20 Hours, Support Working While Charging
• Multifunctional USB-C Port for Charging and Monitoring
• Low Latency < 20ms, Working Range Up to 200m(Open Area)

Notice

Due to 2.4G wireless characteristics, please keep face to face when using, and don’t turn your back to the receiver, othelVv’ise it is easy to generate breakpoints, which is a normal phenomenon
Please pay attention that it can not realize STEREO function when in single- channel mode
Please do not expose the product to rain or moisture, and avoid having water or other liquids spilled on it
Please do not use or store the product near any heat sources such as radiators, stoves, or other heat-producing appliances
This product is a high-precision product, please prevent it from dropping or colliding

Product List

| | |
---|---|---|---
Vimo C
Transmitter(TX)| Vimo C
Transmitter(TX)| Vimo C-RX
Receiver(RX)| Bat case

Accessories

1. Wind Muff
2. 3.5mm TRS-TRRS Audio Cable
3. 3.5mm TRS-TRS Audio Cable
4. 2 in 1 Charging/Monitoring Adapter Cable
5. 3 in 1 Charging Cable
6. USB C-USB A Charging Cable
7. User Manual
8. Warranty Card

The accessories of each combination include:

C1 =①+②+③+④ + ⑤+⑥+⑧
C2=①+②+③+④ + ⑤+⑥+⑧
C3=①+②+③+④ +⑤+⑥+⑧

Components and Instruction

Transmitter (TX)

1. Internal Mic

2. Working Status Indicator: Blink blue when unpaired; Show blue when paired;
   Show green when denoise is on; Show red when muting

3. Belt Clip

4. Power/Muting Button: Long press for on/off; Short press for muting

5. Denoise/Pairing Button: Short press for denoise on/off; Long press for pairing

6. Charging Contact

7. USB-C Charging Port

Receiver (RX)

1. 3.5mm TRS Audio Output Port

2. Power/Mono/Stereo/Safety Mode Switch Button: Long press for On/Off; Short press for mono/stereo/safety mode switch

3. LCD Display

4. Belt Clip CID

5. USB Charging/Monitoring Port: Insert USB-C headphone to monitor or connect the receiver and the power bank/DC power to charge; Connect the 3.5mm headphone to monitor and the power bank/DC power to charge simultaneously via the 2 in 1 monitoring/charging cable

6. Volume Control/Pairing/Display Rotation Button:
   Short press for volume adjustment of channel A; Long press for display rotation

7. Volume Control/Pairing/Display Rotation Button:
   Short press for volume adjustment of channel B; Long press for display rotation

8. Charging Contact

Bat Case

1. Power Indicator: There are four power indicator lights, one of which represents 25% of the bat case’s power
2. Reset Hole: If there is an abnormal phenomenon such as a charging problem, insert a reset pin into the reset hole to reset it
3. CID USB-C Charging Port

| The transmitters and receiver are automatically turned off when placed in the Bat Case II and turned on automatically when removed
---|---

Screen Display

Receiver(RX)

Installation and Usage

Pairing (All have been paired at the factory. If you need to re-pair, please follow the following description.) When neither of the transmitters are paired, turn on the transmitters and receiver; Long press two pairing buttons on the receive Eff simultaneously until the display shows “PAIR” (If your receiver’s display is dim, short press any button on eto light up the display first); Long press the paining buttons on the two transmitters respectively until they get paired. During pairing, the indicators on the transmitters blink blue rapidly; When paired, the indicators on the transmitters show blue, and the receiver’s display shows the status of the transmitters When one of the transmitters is not paired, turn off the paired transmitter first and follow the steps above to pair the unpaired one. When it is paired, turn on the other paired transmitter to use

Usage

1. Transmitter Installation
   Install the transmitter on the collar so that the internal mic points to the sound source
   

2. Receiver Installation
   Work with Camera
   Hold the receiver through the belt clip to the camera’s hot shoe mount, then connect the receiver with camera through the 3.5mm TRS-TRS audio cable
   
   Work with Mobile Phone/Computer
   Connect the receiver and the mobile phone/computer via the 3.5mm TRS-TRRS audio cable and corresponding audio adapter cable (Please purchase audio adapter cable by you reshelf)
   

3. Monitoring/Charging
   Method One
   Connect USB-C headphones to monitor or connect the power bank/DC power using the USB C-USB A charging cable to charge the receiver
   
   Method Two
   Connect 3.5mm headphones through the 2 in1 charging/monitoring adapter cable for monitoring and connect the power bank/DC power to charge the receiver at the same time
   

Specification

Wireless Band Antenna
Transmitting Power| 2402 – 2480MHz
Ceramic antenna 6.18dBm
---|---
Sensitivity| -32dB ±2dB
Polar Pattern| Omnid irectional
Frequency Response SIN
Equivalent Noise
Maximum SPL Dynamic Range| 80Hz 20kHz 70dB
24dBA
110dB
86dB
Sound Delay| <20ms
Battery| TX: Built -in Li-ion Battery 140mAh 3.7V RX: Built -in Li-ion Battery 230mAh 3.7V
Bal Case: Bu ilt -in Li-ion Ballery 1400rnAh 3.7V
Charg ing Time
Standby Time| TX: 2 Hours; RX: 2 Hours; Charg ing Case: 2 Hours
TX: 8 Hours; RX: 8 Hours; Bat Case: 2 times for two transmitters and one rece iver charged simultaneously
Net Weight| TX: 13g; RX: 19g; Bat Case: 90g
Dimension| TX: 16x20x50mm; RX: 17x26x50mm; Bat Case: 31x63x80mm
Operating Temperature
Storage Temperature| QC – 50°C

Website: comica-audio.com
Facebook: Comica Audio Tech Global
Instagram: Comica Audio
YouTube: Comica Audio

FCC Warning

This device com plies wth part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority lo operate the equipment. This equipment has been lasted and found to comply with the limits for a Claps 13 digital device, pursuant to parl. 15 of the FCC Rules. These limits  are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with thc imtruclio ns, may cause harmful interference to radio communications. However, there is no guarantee that. interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or rclocatc the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Cornsult the dealer or an experienced radio/TV technician for help

JC Camion:
Radio Standards Specification RSS-Gen, issue 5
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’ s license-exempt RSS(s). Operation is subject to the filming two conditions:
That device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. RF exposure statement: The device bas been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction .

The device is in compliance with the essential requirement and other relevant provision of the UK Radio Equipment regulation SI 2017 :1206(as amended)
The device can be used in portable exposure restriction

Declaration of Conformity:
Hereby, Shenzhen Commlite Technology Co., LTD declares that the product type Vimo C is in compliance with the following Regulations : Radio Equipment Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electrical Equipment 2012. The Full test of the UK declaration of conformity is available at the following internet address:  https://www.comica- audio.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>