axtion CWA647MP Extreme MP iPad 10.2-Inch 9th Gen Tablet User Guide
- June 3, 2024
- axtion
Table of Contents
axtion CWA647MP Extreme MP iPad 10.2-Inch 9th Gen Tablet
INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS CAREFULLY. IMPROPER USE OF THE CASE COULD BE DETRIMENTAL. This aXtion Extreme Case is designed only for the specific tablet listed on the box containing the Case. Thus, the Case is only intended for and only warrantied for proper use with that specific tablet and not for use with another device type. Because different generations of tablets have different specifications, please refer to the packaging for your aXtion Extreme Case to determine whether your tablet will be compatible with the aXtion Extreme Case you have purchased. Do not use the aXtion Extreme Case if it is damaged or not functioning properly for any reason
CERTIFICATIONS
aXtion Extreme Cases are C1D2 | C2D2 | C3D2 | ATEX Zone 2 | ATEX Zone 22 certified, meaning they are approved for usage in hazardous locations which require these certifications. Please refer to the certification label on the case and/or the product page on The Joy Factory website for the specific certifications. The certified Case and tablet solution is installed in The Joy Factory Inc’s certified labs and is verified with a tamperproof label. If the tamperproof label is removed then the solution is void. The Case’s label should be inspected upon deployment and periodically while in-use. When the tamperproof label is intact, the Case provides protection to tablets in environments where explosion or fire hazards exist due to the presence of flammable gases, flammable or combustible liquid-produced vapors, combustible dusts, or ignitable fibers or flying materials All aXtion Extreme Cases are certified IP68 waterproof. The IP68 rating means that the aXtion Extreme Case is certified as “dust and watertight” (that is, no dust or water will enter the Case when it is properly installed and used). All aXtion Extreme Cases are also designed to be shock resistant and can physically and functionally withstand infrequent, non-repetitive shocks encountered in various environments.
NO ALTERATIONS
Any alteration to your aXtion Extreme case is prohibited and will not be covered under any of the following certifications: C1D2 | C2D2 | C3D2 | ATEX Zone 2 | ATEX Zone 22 with MIL-STD-810H Military Grade and IP68 Waterproof. In addition, any alterations will void all warranties, for the Case. The Joy Factory Inc. disclaims any and all liability for damages arising from use of an altered aXtion Extreme case. NOTE: Removal of the device from the aXtion Extreme Case breaks the tamperproof label thus voiding all certifications. The Joy Factory Inc. disclaims all liability and all warranties, whether expressed or implied, in situations where the Case is mishandled.
EXPRESS WARRANTY
The Case is covered under a one-year manufacturing warranty from the date of purchase and can be replaced free of charge for any manufacturing defects. If you believe the Case has a manufacturing defect, cease use immediately and contact The Joy Factory Inc. by email at support@thejoyfactory.com or by telephone at 949-216-8888, Monday through Friday, 9:00 a.m. to 5:00 p.m., Pacific Standard Time. The Joy Factory Inc. will only replace a Case that has a manufacturing defect. The Joy Factory is not liable to replace or pay for replacement of your device or any additional items which may be damaged from use of a Case with manufacturing defects or the use of the Case with other cases and bumpers
WARRANTY DISCLAIMER
EXCEPT TO THE EXTENT SET FORTH IN THE EXPRESS WARRANTY ABOVE AND AS PERMITTED BY LAW, THE JOY FACTORY INC. PROVIDES THE CASES ON AN “AS IS” BASIS, AND DISCLAIMS ALL WARRANTIES AND CONDITIONS WITH RESPECT TO THE CASES, WHETHER ORAL, WRITTEN, STATUTORY, OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NONINFRINGEMENT OF THIRD-PARTY RIGHTS. The Joy Factory Inc. does not provide a warranty for the tablet computer installed into the aXtion Extreme Case.
LIMITATION OF LIABILITY
IN ADDITION TO THE ABOVE WARRANTY DISCLAIMER, TO THE MAXIMUM EXTENT PERMITTED
BY LAW, IN NO EVENT WILL: (A) THE JOY FACTORY, INC., ITS PARTNERS, OFFICERS,
DIRECTORS, AGENTS, EMPLOYEES, AFFILIATES, PARENTS, SUCCESSORS, ASSIGNS,
LICENSORS, SUPPLIERS, AND RESELLERS (COLLECTIVELY, “THE JOY FACTORY PARTIES”)
BE LIABLE FOR ANY CONSEQUENTIAL, EXEMPLARY, SPECIAL, OR INCIDENTAL DAMAGES,
INCLUDING ANY DAMAGES FOR PERSONAL INJURY OR LOST DATA, PROFITS, EQUIPMENT OR
PROPERTY, ARISING FROM OR RELATING TO THE CASES, EVEN IF THE JOY FACTORY
PARTIES KNEW OF, SHOULD HAVE KNOWN OF, OR WERE ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES; AND (B) THE TOTAL CUMULATIVE LIABILITY OF THE JOY FACTORY
PARTIES ARISING FROM OR RELATED TO THE CASES, WHETHER IN CONTRACT, TORT OR
OTHERWISE, EXCEED THE AMOUNT OF $100.00. THIS LIMITATION APPLIES NO MATTER HOW
MANY CASES YOU OWN, AND WILL NOT BE INCREASED BY THE EXISTENCE OF MORE THAN
ONE INCIDENT OR CLAIM
CALIFORNIA PROPOSITION 65 NOTICE
The State of California requires that all manufacturers notify their consumers
of certain chemicals that may be found in their products, even if the amount
is very slight. This is so because, if ingested, exposure to these chemicals
could contribute to higher risks of cancer or birth defects. The general
Proposition 65 notice is as follows:
WARNING: This product contains a chemical known to the State of
California to cause cancer, birth defects or other reproductive harm.
All of The Joy Factory Inc.’s Cases are safe and are required to meet
applicable federal health and safety standards. A variety of products on the
market today contain safe levels of these chemicals, and when used as
intended, do not expose the consumer to any greater risks.
For more information on California’s Proposition 65, please see:
https://oehha.ca.gov/proposition-65/law/proposition-65-law-and-
regulations
User Guide
Inspections before entering the hazardous environment
- Label: Check the certification label to ensure the case is certified for your work environment, and the tamper proof label is not missing or appears to be tampered.
- Case Body: Inspect the case and ensure there is no damage such as cracks, or missing parts.
- Screen Protector and Camera Lens Cover: Ensure the screen and lens cover have no crack and is formly adhered to the case.
- Port Cover: Ensure all port covers are completly closed.
Label Inspection
This hazardous location certified solution is void if the tamperproof label is
broken or appears tampered. Due to the nature of hazardous locations this case
and tablet solution will be utilized in, its imperative to ensure the install
tamperproof label is fully intact and shows no signs of tampering. If at any
time the tamperproof label is missing or appears to be tampered, whether it is
during initial deployment or during regular usage, place the case out of
service and contact your reseller. Each case solution should come with two
standard labels. The first label details the certification of the case and
appears on the backside of the case. The second is the tamperproof label which
is placed on the outer shell of the solution where the two outer shell pieces
meet
Product Features
Accessories
Sun Visor | Harness & Shoulder Strap Harness secures the case for safe
transport and provides coverage from sun glare.
FAQs
How does the user charge the device?
This case and tablet solution cannot be charged anywhere in a hazardous
environment. When in a safe environment free from explosive vapors, particles
and debris the device can be charged by opening the Charging Port Cover on the
case.
Can I open the case to remove the device for servicing?
The tamperproof label must remain intact at all times. This ensures the tablet and case were installed in our certied installation centers. Tampering or removing the label voids the certied installation of the solution. See section “Label Inspection”.
What do I do if I need technical support?
The aXtion Extreme case is covered under a one-year manufacturing warranty. The tablet is covered by the tablet manufacturer’s warranty. Contact tablet manufacture for tablet technical support or warranty service. Contact The Joy Factory for case technical support and warranty service, or reinstallation of the case if a tablet replacement or repair is needed.
Cleaning Instructions
To safely clean the case and tablet solution use a cleaning cloth from the below list of approved cleaners. Should one of these cleaning solutions not be available a damp cloth may be used. HAZARD: Never use a dry cloth to clean or wipe the case as this would cause a hazard by producing static electricity.
Approved Cleaners
- Sani-Cloth® AF3
- Super Sani-Cloth®
- CaviWipesTM
- Clorox Healthcare® Bleach Germicidal Wipes
- Oxivir® Tb
Certifications
- North America: Class I, Div. 2 & Class II, III Div. 1 & Div. 2, Groups A – G
- Europe: ATEX Zone 2 & Zone 22 ATEX standards and issue dates
- EN IEC 60079-0:2018
- EN 60079-11:2012
- EN 60079-15:2019
- EN 60079-31:2014
This case is certied and deemed safe to be used in potenially hazardous environments. Please refer to the certication label on the case or product page on The Joy Factory’s website www.thejoyfactory.com for the certication information.
References
- ry.com
- The Joy Factory | Tablet Cases | Mounts | Kiosks
- oehha.ca.gov/proposition-65/law/proposition-65-law-and-regulations
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>