HORL 2 Cruise Sharpener User Manual
- June 3, 2024
- HORL
Table of Contents
HORL® 2 Cruise
User Manual
2 Cruise Sharpener
Diamond grinding disc
The industrial diamonds we use are suitable for efficiently sharpening knife
steels of any hardness without needing water.
Properly used HORL® diamond grinding discs should not need replacing. With a
grit size of 46 μm our standard disc grinds efficiently and precisely. A high-
quality sharpening result is quickly achieved.
Stainless steel honing disc
The stainless steel honing disc smooths the cutting edge after the grinding
process and its integrated grooves remove any burr or residual particles. Just
a few rolls back and forth are sufficient. The grinding discs of the are not
exchangeable.
MAGNETIC ANGLE SUPPORT
The magnetic angle support guarantees a constant and reproducible grinding
angle with every use. This minimizes the material removed and the knife blade
rapidly achieves an even and precise sharpness.
The neodymium magnets inside the support hold the knife firmly in the required
position while grinding. A fine silicone membrane (S-Pad) augments the
magnetic grip of the knife by its anti-slip effect and protects the magnets
from grinding particles and other impurities.
Keeping the grinding angle constant every time is an important factor for the
longevity of your knives.
20° grinding angle
The 20° grinding angle quickly achieves a robust sharpness. The knife retains
its sharpness for a long time thanks to the stable cutting edge and is
suitable for a wide variety of application in everyday kitchen use. It also
gives many outdoor and pocket knives a stable edge and excellent sharpness for
daily use.
In principle, kitchen knives of any quality can be sharpened using the 20°
angle.
As the condition and sharpening history of a knife is often not known from the
outset, a reproducible grinding angle must first be established. Regrinding
will subsequently only require rolling back and forth a few times and this
means much less material is removed.
SAFETY INFORMATION
The HORL®2 CRUISE is not intended for use by persons with reduced physical or sensory capabilities or who lack experience and knowledge, such as children. It is only intended for sharpening smooth kitchen knives (not serrated blades). Misuse of the appliance and/or disregard for these instructions can lead to serious impairment of the product‘s longevity and other risks.
| Risk of injury from sharp blades
Use the HORL®2 CRUISE on a non-slip, clean, dry and level work surface.
Hold it only by the roller grip during use and avoid dangling a finger.
By touching the knife’s edge there is danger of cutting yourself badly.
---|---
| Danger from strong magnets
The magnetic angle support contains strong neodymium magnets and should
therefore be kept out of the reach of children. Magnets can cause damage to
things like bank cards, pacemakers, computers, mobile phones and other
electronic devices. If in doubt, exercise extreme caution.
| Care & Maintenance
The HORL®2 CRUISE and the magnetic angle support should be protected from
water. If necessary, you can clean the diamond grinding disc with a pencil
eraser to remove any grinding residue. When there is a lot of contamination,
the diamond grinding disc can be unscrewed and thoroughly washed in warm
water, with a little washing-up liquid and a brush.
BEFORE YOU START
| The amount of time required will vary when a knife is sharpened for the
first time with the HORL®2 CRUISE , depending on the condition of the
blade and the quality of the steel. The edge must first acquire the chosen 20°
grinding angle. However, thanks to the constant grinding angle, only a few
rolls back and forth are needed for subsequent resharpening.
---|---
| When a HORL® diamond grinding disc is used for the very first time, some
excess diamond particles are eliminated. This is audible, but quite normal and
occurs only once. After a few minutes, grinding will become quieter and the
grinding disc’s surface much finer. The grit of the disc should now be only
slightly rough to the bare finger. The disc has reached its working surface
condition.
The marker pen method
Use the marker pen method to visually check the success of the grinding
process.
Carefully draw the felt tip of a marker pen along the entire knife edge, so
that it simultaneously leaves ink on both sides. Once the ink is removed by
grinding on both sides, the desired angle is achieved.
horl.com/faq
THE IMPORTANT STEPS
-
AFFIX
Place the magnetic angle support with its silicone feet on a worktop and attach the knife to the S-Pad so that it is held securely level with its edge facing upwards. -
GRIND
Hold the sharpener on the worktop by the roller grip with one hand and press firmly on the magnetic angle support with the other hand. Move the roller of the sharpener back and forth in smooth movements and with only slight pressure of the diamond grinding disc along the entire cutting edge. -
HONE
To refine the cutting edge and remove any burr, rotate the sharpener 180° and repeat step 2 with the stainless steel honing disc. -
OTHER SIDE
Turn the knife around and repeat steps 1 to 3 with the other side of the blade to achieve an even sharpening result.
AFFIXING KNIVES CORRECTLY
Broad blades
Place the spine of the knife on the worktop
so that the edge faces upwards. Slide the knife
towards the magnetic angle support until the
magnets engage and the blade is firmly held.| Narrow blades
Attach the knife to the magnetic angle support
with the blade facing upwards so that the cutting edge is level and protrudes
above the contact pad. In this case, the spine will not touch the worktop.|
Extremely broad blades
To grind particularly broad blades, where the cutting
edge stands higher than the grinding disc, elevate the
sharpener with a suitably thick cutting board to ensure
contact with the cutting edge is within the radius of the diamond grinding
disc.
---|---|---
| |
Tip: Wipe away any residue of grinding particles with a kitchen cloth. For awesome sharpness, strop a few times with the HORL® Leather.
We are convinced that you always have to break new ground to achieve
impressive results.
With the HORL®2 CRUISE you can sharpen your favourite knives efficiently
and precisely, giving the best possible result and making every knife a joy to
use.
Our regional production results in the shortest distances to and from
Freiburg, which not only results in development synergies it also ensures our
products are always of the highest quality. We wish you sharp knives at all
times.
Warm greetings from Freiburg
Your HORL® team
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>