COMMAND LIGHT C-Lite Powerful Concentrated Light User Manual

COMMAND LIGHT C-Lite Powerful Concentrated Light

LIMITED WARRANTY

COMMAND LIGHT warrants that the equipment is free from defects in materials and workmanship when used and operated for a period of five years. The responsibility of COMMAND LIGHT under this limited warranty is limited to the repair and replacement of any parts found defective. Parts must be returned to COMMAND LIGHT at 3842 Redman Drive, Ft Collins, Colorado 80524 with transportation charges prepaid (C.O.D. shipments will not be accepted). Prior to returning defective parts to COMMAND LIGHT, the original purchaser shall make a claim in writing to COMMAND LIGHT at the above address indicating the model number, serial number and type of defect. No parts or equipment will be received by COMMAND LIGHT for repair or replacement under this warranty without specific written authority from it in advance. Any parts damaged by improper installation, overloading, abuse or accident of any type or cause are not covered by this warranty. All equipment manufactured by us is tested before leaving our plant, and is shipped in good working order and condition. We therefore extend to the original purchasers the following Limited Warranty for the period of five years from the original date of purchase

1. This warranty does not apply to defects caused by accident, misuse, neglect, or wear andtear, nor can we be held responsible for incidental and consequential expense and loss, nordoes this warranty apply to equipment where alterations have been executed without ourknowledge or consent. These conditions are readily discernable when the equipment isreturned to us for inspection.
2. On all component parts not manufactured by COMMAND LIGHT, their warranty is to theextent that the manufacturer of such component warrants them to COMMAND LIGHT, ifat all. Look in your local business telephone directory for the nearest repair station for thebrand of parts you have or write to us for the address.
3. If equipment received has been damaged in transit, a claim should be made against thecarrier within three days, as we assume no responsibility for such damage.
4. Any service other than our Authorized Service voids this warranty.
5. This warranty is in lieu of and is intended to exclude all other warranties, express orimplied, oral or written, including any warranties of MERCHANTIBILITY or FITNESSfor a particular purpose.
6. Travel time paid at a maximum of 50% and only if pre-approved.

Breakage or Damage During Shipment

The transportation company is fully responsible for all shipping damage and will resolve problems promptly if you handle it correctly. Please read these instructions carefully.
Examine the contents of all shipping cases. If you find any damage, call your transportation agent at once and have them make a description on the freight or express bill describing the damage and the number of pieces. Then contact us and we will send you the original bill of lading. Also promptly contact the transportation company and follow their procedure for filing a claim. Each company will have a unique procedure to follow. Please note, we cannot and will not enter claims for damages. If we filed claim here, it would be sent to your local freight agent for verification and investigation. This time can be saved by you filing the claim directly. Every consignee is on the ground floor, in contact with the local agent who inspects the damaged goods, and thus, each claim can be given individual attention. Since our goods are packed to comply with the regulations of all railroad, truck, and express companies, we cannot allow deduction from any invoice because of any damage, however, be sure to file your claim promptly. Our goods are sold F.O.B. factory. We take receipt from the transportation company certifying that the goods were delivered to them in good order and our responsibility ceases.
It is seldom that any breakage or damage occurs in any of our shipments and in no case will the customer be out any expense if they follow the above instructions.
Be sure to keep all damaged goods subject to examination of the truck or express company inspector, who may call on you some time later. These damaged goods, of course, will belong to them, and they will inform you what to do with them. If you dispose of these damaged goods, your claim may not be paid.

General Description and Specifications

Electrical Wiring

The C-Lite is provided with 25 feet of 12AWG-2 Conductor Cable color coded with red and black wires. Provide a 12VDC+ signal on the red wire and a 12VDC Ground signal on the black wire to power the C-Lite. Reversing these wires may cause damage to the internal circuitry or components of the C-Lite.
A 20 amp fuse is recommended to protect the C-Lite from electrical damage

Installation

The C-Lite must be installed by a designated installation facility by qualified personnel only. All safety precautions must be thoroughly understood before installation. Please consult the factory for additional installation information assistance

Included Parts

• Four (4) – ¼-20 x 1” Hex Head Bolt
• Eight (8) – ¼” Flat Washer
• Four (4) – ¼-20 Nyloc Nut
• One (1) – ½” Straight Sealcon with Nut
• One (1) – Command Light Screwdriver
• One (1) – User Guide

Tools Required

• 7/16” Wrench and Socket
• Drill with assorted bits

Maintenance

Cleaning

The C-Lite is constructed with corrosion resistant aluminum and stainless steel fasteners. To further enhance corrosion resistance all exposed surfaces receive a powder coated paint finish. To assure years of trouble free service periodically clean all external surfaces with a mild detergent solution and a gentle spray of water. DO NOT USE A HIGH-PRESSURE WASHER, which will force water into sensitive electric circuitry

Troubleshooting

If the C-Lite stops operating, disconnect and reconnect power. If operation does not resume, test for a valid 12VDC power source and ground. If this does not remedy the issue, contact Command Light at 1-800-797-7974 for Technical Support.

Wireless Option

Replacing Battery

The wireless controller for the C-Lite is powered with a CR2032 button style battery. Follow these steps to replace the controller battery:

1. Remove red cover grip from the controller by stretching the bottom portion aroundthe back and sliding it towards the antenna.
2. Open the wireless controller by loosening the 4 screws located on the back of the controller.
3. Slide the old battery out of the retainer clip on the transmitter circuit board being careful to not press the “Code Set” button located above the battery.
4. Slide the new battery into the retainer clip with the + Side Up.

Options

Manual Rotation Base
If the C-Lite was ordered with the Manual Rotation Base option, it comes pre- installed. Mounting hole pattern of the Manual Rotation Base is the same as the C-Lite. This option adds 2 inches to the overall height of the C-Lite.

Electric Rotation Base
If the C-Lite was ordered with the Electric Rotation Base option, it comes pre-installed. Mounting hole pattern of the Electric Rotation Base is the same as the C-Lite. This option adds 3 inches to the overall height of the C-Lite.

Technical Specifications

Electric Rotation

Parts List – Exploded View

Wiring Diagram

THANK YOU

Please allow us to express a simple thank you for investing in a COMMAND LIGHT product. As a company we are dedicated to producing the very best and most versatile flood lighting package available. We take great pride in the quality of our work and hope that you will find many years of satisfaction from the use of this equipment. Should you have any problems with your product please do not hesitate to contact us.

3842 Redman Drive Fort Collins, CO 80524 PHONE: 1-800-797-7974 FAX: 1-970-297-7099 WEB: www.CommandLight.com

References

• Fire Truck Scene Lights | Command Light Towers and LED Traffic Advisors

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>