WhisperKOOL Phantom 24V Thermostat Conversion Kit Installation Guide
- June 3, 2024
- WhisperKOOL
Table of Contents
WhisperKOOL Phantom 24V Thermostat Conversion Kit
We manufacture, test and certify 100% of our wine cooling units in the USA. By sourcing the best components and closely controlling our manufacturing processes, we can assure the highest-quality, lowest defect manufacturing rates in the industry.
Copyright © 2018. WhisperKOOL. All rights reserved.
WhisperKOOL copyrights this manual, the product design, and the design
concepts, with all rights reserved. Your rights with regard to the hardware
and manual are subject to the restrictions and limitations imposed by the
copyright laws of the USA. Under copyright laws, this manual may not be
copied, reproduced, translated, transmitted, or reduced to any printed or
electronic medium or to any machine-readable form, for any purpose, in whole
or in part, without the written consent of WhisperKOOL. Every effort has been
made to ensure that the information in this manual is accurate. WhisperKOOL is
not responsible for printing or clerical errors. WhisperKOOL reserves the
right to make corrections or improvements to the information provided and to
the related hardware at any time, without notice. Vinothèque and WhisperKOOL
are registered trademarks, and ECE is a trademark of WhisperKOOL. All rights
reserved. Mention of third-party products is for informational purposes only
and constitutes neither an endorsement nor a recommendation. WhisperKOOL
assumes no liability with regard to the performance or use of these products.
INTRODUCTION
Customer Service
Thank you for purchasing a WhisperKOOL 24V Thermostat Conversion Kit. We
strive to provide the highest-quality products and the best possible customer
service. If you have any questions about your system, please call us at
1-800-343-9463 or visit
whisperkool.com.
Using the Manual
This installation manual is intended to provide detailed instructions for the
installation of the 24V Thermostat Conversion Kit on the Phantom cooling
system. In order to ensure the proper longevity of your cooling unit, the
equipment should be installed as outlined in this manual. Please read and
review this manual carefully and keep it for future reference.
What is a 24V Thermostat Conversion Kit?
The 24V Thermostat Conversion Kit is a WhisperKOOL product that allows the
customer to switch from the provided standard 120V controller to a 24V
thermostat of their choosing (i.e. Nest, Ecobee, Honeywell etc.)
Note: 24V Thermostat not provided by WhisperKOOL
How Does the 24V Thermostat Conversion Kit Work?
The 24V Thermostat Conversion Kit allows the customer the ability to utilize a
24V smart thermostat to control the operation of their WhisperKOOL unit. Note:
24V Thermostat must be placed inside the wine cellar in a central location,
away from direct airflow.
Note: WhisperKOOL does not provide technical/customer support for any 24V
thermostat.
Please contact the manufacturer of your chosen 24V thermostat for
troubleshooting.
STEP1: RECEIVING & INSPECTING THE KIT
Upon receiving your 24V Thermostat Conversion Kit:
- Inspect the packaging for any obvious signs of damage or mishandling before opening the container.
- Note any discrepancies or visual damage on the bill of lading before signing.
- Review the packing slip to verify contents.
- Check the model number to ensure it is correct.
- If any items listed on the packing slip do not match your order information, contact WhisperKOOL Customer Service immediately.
REMEMBER:
- Inspect the kit before installation. If damage is found, please contact your distributor or WhisperKOOL Customer Service at 1-800-343-9463.
- Verify that you have received all of the items on the component list below and that the kit corresponds with your specific WhisperKOOL cooling system.
- The system is intended for use in properly designed and constructed wine cellars. Hire a professional wine storage consultant with a valid contractor’s license to build your wine cellar.
- WhisperKOOL recommends that all 24V Thermostat Conversion Kits be installed by a certified HVAC-R technician only.
Evaporator unit components provided:
- 24V conversion kit enclosure
- Installation instructions
- Accessory kit
- Molex adapter
Tools needed:
- Wire cutters
- Wire strippers
- 5/16” nut driver
- 11/32” nut driver
- Phillips #1 screw driver
- Needle nose pliers
- 5/16” drill bit
Accessory Kit Items:
- Cable tie (x8)
- Cable tie holder (x3)
- Wire nut (x4)
- Strip of Cork Tape
- Rubber grommet
Components Needed (not included):
- 24V thermostat
- 18-5 thermostat wire
After verifying that you have received all of the correct components for your specific system, please keep the 24V Conversion Kit in its original box until you are ready for installation. This will allow you to move the product safely without damaging it. When you are ready to remove the product from the box, refer to the installation instructions. TIP: Save your box and all packaging materials. They provide the only safe means of transporting/shipping the unit.
STEP:2: BEFORE YOU START
- Shut off power to the evaporator and condensing unit.
- Disconnect the cooling unit from the power source.
- WARNING: Failure to disconnect the power may cause electrical shock, which can result in injury or death.
- Note: If the unit is hard-wired to a dedicated power source, shut off the designated breaker.
24V THERMOSTAT CONVERSION KIT INSTALLATION INSTRUCTIONS
-
Disconnect power from the cooling unit.
Note: If the unit is hard-wired to a dedicated power source, shut off the designated breaker. -
Using a 5/16” nut driver to loosen the screws securing the evaporator access panel to the unit.
-
Remove the access panel from the unit.
-
Locate the controller enclosure as shown. Remove the two 11/32” hex nuts securing the enclosure to the divider.
-
Pull the enclosure from the unit forward and remove the lid using a Phillips screwdriver.
-
Locate the following wires: Pb1, Pb2, Display, and flag connector from terminal #6.
-
Disconnect Pb1, Pb2, Display, and flag connector from terminal #6. Next, remove the wires from the enclosure as shown.
-
Cut the flag connector from the black wire as shown.
-
Disconnect the 4-pin Molex connector as shown. The original controller enclosure is now safe to remove completely from the unit.
-
The remaining wires which were removed from the previous enclosure are no longer needed. They can be positioned out of the way as shown or cut and removed from the unit.
-
Locate the 24V Conversion Kit. Remove the top by removing the 4 screws.
Note: The conversion Kit will be mounted in the same location where the previous controller box was mounted. -
Locate the Lever connector which houses the black wires as shown.
-
Route the black wire which was removed from the previous enclosure into the new enclosure.
-
Insert the black wire into the lever connector as shown.
-
Re-install the box cover.
-
Connect the 4-pin Molex connector from the new 24V kit to the existing unit wire harness as shown.
-
Install the new 24V Kit enclosure in the same location as the previous enclosure using the previously removed hex nut hardware.
-
Route 18/5” thermostat wire from the thermostat location to the evaporator unit.
-
Strip off 6” from the thermostat wire casing. Cut and remove the white thermostat wire. Strip off about 1/4” of the blue, red, green, and yellow thermostat wire casing to expose the copper.
-
Drill a 5/16” hole in the previously removed access panel as shown.
-
Insert provided grommet into the hole. Insert the thermostat wire through the 5/16” hole.
-
Connect thermostat wires with the provided wire nuts by color matching red to red, blue to blue, green to green, and yellow to yellow. Secure the wires to the enclosure using cable ties and an adhesive pad.
-
Install the evaporator access panel onto the unit using the six previously removed screws. Use cork tape or duct tape to seal around the hole through which the wire was run.
-
The conversion is now complete. Reconnect power to the evaporator unit.
-
The 24V Thermostat Conversion Kit has been successfully installed.
-
WhisperKOOL
-
1738 E. Alpine Ave Stockton, CA 95205
Documents / Resources
|
WhisperKOOL Phantom 24V Thermostat Conversion
Kit
[pdf] Installation Guide
Phantom 24V Thermostat Conversion Kit, Phantom, 24V Thermostat Conversion Kit,
Thermostat Conversion Kit, Thermostat Kit, Thermostat, Phantom 3500, Phantom
5000, Phantom 8000
---|---
References
- WhisperKOOL | Wine Cellar Cooling Units | Made In The USA
- WhisperKOOL | Wine Cellar Cooling Units | Engineered, Designed and Assembled In The USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>