BUMPSTER OR2302 Wireless Speaker Instruction Manual
- June 3, 2024
- BUMPSTER
Table of Contents
BUMPSTER OR2302 Wireless Speaker
PRODUCT FEATURES
- Wireless connection up to 33 feet I 1 O m
- Built-in 3W amplified speaker and bass enhancer
- Built-in rechargeable battery
- Speaker phone call-choice functionality
- AUX 3.5 mm audio input
- Compatible with smartphones and other multimedia player devices
CHARGING THE SPEAKER
As shown (fig. 1), connect the micro-USB end of your charging cable to the
micro-USB port on the Bumpster, and the standard USB end to the USB port of a
power source, such as a laptop or wall adaptor. A red LED will light up in the
back to indicate charging. When the speaker is fully charged (approx. 1.5
hours for a full recharge), the back LED will turn blue.
WIRELESS PAIRING
Move the slide switch on the bottom of the unit to [BT] (fig. 2). This will
power ON the speaker within 3 seconds, as indicated by the blue LED on the
front. The LED will blink quickly to show that it is ready for pairing. Access
the wireless settings on your device and select “OrigAudio-D” to pair. You
will hear a beep from the speaker and see the blue LED flash steadily (1.5
times every second), confirming that a connection has been made.
If you need to pair the Bumpster to a new smartphone, first disable the
wireless pairing functionality on your original smartphone and then enable
wireless pairing on the new smartphone. Switch the speaker from [OFF] to [BT],
and repeat the pairing instructions from the previous paragraph.
WIRED CONNECTION
You may use the provided cable to connect the speaker to your device via a
wired connection. Move the slide switch on the bottom of the unit to [AUX].
Then connect the micro-USB end of your charging cable to the micro-USB port on
the Bumpster, and the AUX end to your mobile device or laptop.
ANSWERING PHONE CALLS
If the speaker is connected to your smartphone and you receive a phone call,
you can operate your phone to answer the call and the Bumpster will act as a
speakerphone.
(Once the speakerphone feature is activated, you may use your smartphone to
transfer the call back to your phone.)
HOW TO USE / CONTROLS
You will need to use your smartphone or device to control your music / audio
(example: adjust speaker volume, play/pause, select audio).
If the battery on your speaker is low, it will emit a beeping sound during
playback (the LED will quickly flash between RED and BLUE). Please charge the
speaker as mentioned in the “Charging the Speaker” section of this manual –
audio will continue to play while the speaker is charging.
PRODUCT SPECIFICATIONS
- Dimensions: W 3.15 x D 3.15 x H 2.48 in (80 x 80 x 63mm)
- Production Weight: 0.4 lbs/ 180g
- Wireless Connection: Up to 33 feet/ 1 Om
- Driver: Dia. 50mm
- Frequency Response (0 dB @ 1 KHz): 100Hz – 20,000Hz
- Amplifier Output: 2.2 W (THD= 10%, 1 KHz @ 0 db)
- Amplifier Max Output: 2. 7 W (1 KHz @ 0 dB)
- Signal to Noise Ratio: >60dB
- Operation Voltage: Min 3V, max 4.2V DC
Built-In 3.7V Lithium-Polymer Rechargeable Battery
- Battery Charging Voltage: typ. 5V; max 5.5V DC (via USB port)
- Battery Charging Current: 500mA max
- Battery Charging Time: 1.5 hours
- Drain Current (power on, no input): 20mA
- Playback Time: Up to 10 hours
- Standby Time: Up to 18 hours
This device complies with part15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference. And
- This device must accept any interference received ,including interference that may cause undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user1s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>