JKGPAD Bluetooth Mini Gamepad for Mobile Phones User Manual
- June 3, 2024
- JKG
Table of Contents
JKGPAD Bluetooth Mini Gamepad for Mobile Phones
Technical Specs
- Bluetooth version: 5.0
- Wireless range: 10m
- Type: 12 buttons gamepad
- Gaming time: Up to 30 hours
- Standby time: Up to 120 hours
- Charging time: Approx 30 minutes
- Gamepad battery: 250mAh
- Gamepad weight: 42g (1.5oz)
- Gamepad size: 64mm x 29mm x 27mm (2.5” x 1.4” x 1”)
- Charging type: USB-C
Package includes:
- 1x JKG gamepad
- 1x mini-USB to USB-C adapter
- 1x User manual
- Indicator LED
- Left bumper button
- USB-C charging port
- Right bumper button
- Foldable arm
- Extendable phone clip
Jacknife Gamer Mini-gamepad
User Manual
For more detailed information about the gamepad, please visit:
www.jacknifegamer.com/info
ON/OFF and Connection:
Press and hold “START” for 3 seconds to turn the gamepad ON or OFF. Gamepad
will immediately go into Bluetooth pairing mode or attempt to connect to a
previous device. Select “Jacknife Gamer” in the phone’s Bluetooth menu to
complete pairing. The gamepad will automatically connect to this phone the
next time it is turned on.
To pair Jacknife Gamer to another phone, turn off Bluetooth on the old phone
before turning on Jacknife Gamer. If Jacknife Gamer cannot detect the old
phone, it will automatically attempt to pair to a new phone. Jacknife Gamer
will turn off if inactive for 15 minutes.
Buttons:
Jacknife Gamer gamepad has the standard UP/DOWN/LEFT/RIGHT, START, SELECT,
A/B/X/Y buttons on the front. The bumper buttons LB/RB are located in the back
to be pressed by the ring fingers when the gamepad is clipped to the phone.
Battery charge
When battery level is low, the center LED will blink and Jacknife Gamer will
turn off automatically after 5 seconds. Recharge Jacknife Gamer with the USB-C
cable of the phone charger for approximately 30 minutes. If phone charging
cable has a Mini-USB cable, use the included Mini-USB to USB-C adapter.
Phone attachment:
To attach the Jacknife Gamepad to a phone, unfold the arm clip and wrap the
clip to the back of the phone in landscape orientation.
Patent granted (2020): USA, Canada, China Patent pending: EPO
Model #: JKG2022A FHVIN: 20220926A
Product code: JKG2022A
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>