Aquis Systems TM1 Series Iot Tracking and Monitoring Module Instruction Manual
- June 3, 2024
- Aquis Systems
Table of Contents
Aquis Systems TM1 Series Iot Tracking and Monitoring Module
Foreword
IOT TRACKING & MONITORING MODULE OPERATING GUIDE FOREWORD Thank you for purchasing an IoT Tracking & Monitoring Module. This manual will show you in detail how to start up the device smoothly. Please read this manual carefully before you start using the device. Please note that any updates to the manual will be made without prior notice. Each time the latest version of the manual is published in the latest product sales. The manufacturer assumes no responsibility for errors or omissions in this manual
About this documentation
Explanation of the symbols used
Warnings
Warnings alert people to hazards that may occur when handling or using the product. The following signal words are used in combination with a symbol:
| CAUTION! Indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
Death can lead
---|---
| WARNING! Indicates a potential hazard that could result in serious personal
injury or death.
Can lead to death
| CAUTION! Indicates a potentially hazardous situation which may result in minor personal injury.
Injuries or property damage.
Symbols in the documentation
The following symbols are used in this document:
| Read the operating instructions before use
---|---
| Instruction manual and other useful information
Product information
Our products are intended for professional users and may only be used by trained, authorized personnel. Operation, maintenance and servicing of the products. These personnel must be made aware of special hazards may be encountered. The product and its ancillary equipment may present hazards if used improperly by untrained personnel or if used improperly.
Declaration of Conformity
We declare under our sole responsibility that the product described here complies with the applicable directives and standards. You will find a copy of the declaration of conformity at the end of this documentation.
Security
General safety instructions
Read all safety and other instructions.
Keep all safety and other instructions for future reference.
General safety instructions:
- Do not cover the type plate or other labels.
- Do not cover any housing openings of the device.
- Do not block switches, indicators and warning lights.
- To avoid surface damage or chemical reactions, check the compatibility of the adhesive with the surface before applying the ON Track Smart Tag.
- Keep away from children.
Read all safety and other instructions.
Description
- Platform-based vehicle or device monitoring and tracking system to provide location coordinates and information about the operating status of the connected device.
- Long distance connectivity via NB-IOT (network provider tbd) GPS module for device tracking
- Water resistant IP69 suitable for outdoor use and for cleaning with high pressure
- Vibration resistant against strong shaking
- Standardized or customized, tailor-made solutions of the IoT Tracking & Monitoring Module possible
- Data transfer to the Aquis Cloud or direct transfer to the customer’s cloud
- Typical battery life 1-3 years depending on parameterization
- Mounting via corresponding recess in outer plate
- Integrated accelerometer 0 to 16g
- Integrated detection algorithms and FFT analysis for autonomous detection of the operating state (rest, transport, engine idle, operation).
- Adaptable to individual devices and vehicles by means of parameters
- Firmware update via “Over the Air” (OTA) via external battery connector
- Optional: Firmware update via “Over the Air” (OTA)
- Optional: Detection of device battery voltage and ignition signal via optional connection to device battery; cable and connector (e.g. DEUSCH connector DT04-3P) tbd
- Optional: bidirectional data interface to device (e.g. CAN bus); cable and connector tbd
IoT Tracking & Monitoring „Schraubmodul“ for Vehicle or Device Monitoring and Processing System on Platform Basis
| |
---|---|---
IoT Tracking & “Schraubmodul”, Basic
Connections: 2-pin connector for connection of the battery module
| IoT Tracking & “Schraubmodul”, Power
2- pin DEUTSCH connector for battery module connection
3- pin DEUSCH connector (DT04- 3P) for external battery and ignition signal
| IoT Tracking & “Schraubmodul”, Power PRO
2- pin DEUTSCH connector for battery module connection
3- pin DEUSCH connector (DT04- 3P) for external battery and ignition signal
Connector for bi-directional interface to device electronics
Functions:
- Integrated accelerometer 0 to 16g
- Integrated detection algorithms and FFT analysis for autonomous detection of the operating state (rest, transport, engine idle, operation).
- Adaptable to individual devices and vehicles by means of parameters
- Firmware update via “Over the Air” (OTA) via external battery connector
- Optional: Firmware update via “Over the Air” (OTA)
- Optional: Detection of device battery voltage and ignition signal via optional connection to device battery; cable and connector (e.g. DEUSCH connector DT04-3P) tbd
- Optional: bidirectional data interface to device (e.g. CAN bus); cable and connector tbd
Technical data
Environmental requirement:
- Designed for extreme loads. Electronics fully potted
- Protection class IP69, temperature -20°to +70°degrees Celsius, also condensing
- Resistant to vibrations
Connections:
- 2-pin DEUTSCH connector for battery module connection
- Optional: 3-pin DEUSCH connector (DT04-3P) for external battery and ignition signal
Mechanical data
- Weight : ≈ 350 g
- Outer dimensions housing: Ø 52 x 35 mm
- Cable length: 180 mm
- Total length: 184.1 mm
- Color: black
- Plastic locknut: M36
Battery module for IoT tracking & monitoring „Schraubmodul“ Vehicle, or device monitoring, and tracking system on platform basis.
Battery Module for IoT Tracking & Monitoring „Schraubmodul“
Lithium battery cpl. potted
|
---|---
Description:
- Battery module for vehicle or equipment monitoring and tracking system
- on a platform basis.
- Water resistant IP69 suitable for outdoor use and for cleaning with high pressure
- Vibration resistant against strong shaking
- Standardized or customized, tailor-made solutions of the battery module for IoT tracking & monitoring „Schraubmodul“ possible
Technical data
Connections:
- 2-pin DEUTSCH plug for
- Connection to the IoT-Module
- Environmental requirement:
- Designed for extreme loads. Electronics fully potted
- Protection class IP69, temperature -20°to +70°degrees Celsius, also condensing
- Resistant to vibrations
Electrical data
- Type: Lithium battery
- Capacity: 3400m Ah
- Output voltage: 7.2 V
- Attention: Battery module only cpl. replaceable
- Battery not rechargeable
Mechanical data
- Weight: ≈ 300 g
- Outer dimensions housing: 89 x 50 mm
- Cable length 150 mm
- Total length: 210 mm
- Color: black
IoT Tracking & Monitoring “Kompaktmodul” for vehicle, or device monitoring and tracking system on platform basis
IoT Tracking & Monitoring “Kompaktmodul” TM2001, battery No connectors,
internal battery| 
---|---
Description:
- platform base to provide location coordinates and information about the
- To provide operating status of the connected device.
- Connectivity for long distances via NB-IOT (network provider tbd)
- GPS module for locating the device
- Water resistant IP69 for outdoor use and for cleaning with
- High pressure suitable
- Vibration resistant against strong shaking
- Standardized or customized, tailor-made solutions
- of the IoT module possible
- Data transfer to the Aquis Cloud or direct transfer to the cloud
- of the customer
- Typical battery life 1-3 years depending on parameterization
- Mounting by means of four screws from the front or rear
Functions:
- Integrated accelerometer 0 to 16g
- Integrated detection algorithms and FFT analysis
- for autonomous detection of the operating state (rest, transport, engine idle, operation).
- Adaptable to individual devices and vehicles by means of parameters
- Firmware update via “Over the Air” (OTA)
- Optional: Detection of device battery voltage and ignition signal via optional connection to the Device battery; cable and plug (e.g. DEUSCH plug DT04-3P) tbd
- Optional: bidirectional data interface to device (e.g. CAN bus); cable and connector tbd
Technical data:
- Environmental requirement:
- Designed for extreme loads. Electronics fully potted
- Protection class IP69, temperature -20°to +70°degrees Celsius, also condensing
- Resistant to vibrations
Electrical data:
- Type: Lithium battery (fully potted)
- Capacity: 3200 mAh
- Output voltage: 7.2 V
- Attention: Battery module only complete replaceable
- Battery not rechargeable
Mechanical data
- Weight: ≈ 350 g
- Outer dimensions housing: Ø 153.2 x 99.3 mm
- Color: black
Battery module for IoT tracking & monitoring „Kompaktmodul“ for vehicle, or device monitoring and tracking system on platform basis.
Battery Module for IoT Tracking & Monitoring „Kompaktmodul“
Lithium battery cpl. potted
|
---|---
- Water resistant IP69 suitable for outdoor use and for cleaning with high pressure
- Vibration resistant against strong shaking
- Standardized or customized, tailor-made solutions of the IoT battery module possible
Technical data
Connections:
- 2-pin DEUTSCH plug for
- Connection to the IoT Tracking & Monitoring „Kompaktmodul“
- Environmental requirement:
- Designed for extreme loads. Electronics fully potted
- Protection class IP69, temperature -20°to +70°degrees Celsius, also condensing
- Resistant to vibrations
Electrical data
- Type : Lithium battery
- Capacity: 3400m Ah
- Output voltage: 7.2 V
- Attention: Battery module only complete replaceable
- Battery not rechargeable
Mechanical data
- Weight: ≈ 300 g
- Outer dimensions housing: 77.7 x 42 mm
- Cable length 20 mm
- Color: black
Scope of delivery
1x IoT Tracking & Monitoring „Kompaktmodul“ with any accessories 1x user
manual
Accessories
Is none provided
Third-party word marks, trademarks and logos
The Bluetooth® word mark and logos are registered trademarks and are the
property of Bluetooth SIG, Inc
Requirements
This chapter contains system requirements
Technical data
Wireless connection
- NB-IoT / LTE-M
- SIM card
Antennas
- NB-IoT / LTE-M
- GPS
Technical details
| DC power supply | Lithium battery 7.2V or external 12V supply |
|---|---|
| Battery life typical | 2-3 years / 5 years |
| Battery capacity lithium battery 7.2V | 3400mAh |
| Voltage range battery | 4,5-8V |
| Voltage range external | 7-15VDC |
| Digital input (ignition signal): | 0-15VDC |
Operation
Commissioning of the IoT Tracking & Monitoring „Kompaktmodul“
It is not recommended to install the unit inside the device (vehicle, etc. )
The GPS reception signal will be reduced and GPS functionality will be
disturbed if the windshield is bonded with a metallic thermal insulation layer
or heating layer.
I mportant
It must be ensured that during mounting on the vehicle/device no cable
protrudes or is pinched
Mounting IoT Tracking & Monitoring „Kompaktmodul“
Drill image IoT tracking & monitoring „Kompaktmodul“
Commissioning of the IoT Tracking & Monitoring „Schraubmodul“
Function display after plugging in the battery
Fastening IoT Tracking & Monitoring „Schraubmodul“
Mounting of battery module for IoT tracking & monitoring „Schraubmodul
“
PIN assignment of the IoT Tracking & Monitoring „Schraubmodul“
PIN assignment of battery module for IoT tracking & monitoring „Schraubmodul“
Mounting locations or possibilities
Deactivation IoT Tracking & Monitoring „Schraubmodul“ and „Kompaktmodul“
Unplugging or removing the battery.
Packing and transport
Risk of material damage.
Store and transport the device only within a temperature range of 0°C to +40°C /32°F … +104°F
RoHS (Restriction of Hazardous Substances)
This chapter contains information on RoHS.
Disposal
The device or battery must be recycled or disposed of separately from
household waste!
Instructions to prevent reasonably foreseeable misuse according to EN 62368-1
Annex M.10
CAUTION: Failure to follow the safety instructions may result in fire,
electric shock, and other injury or damage to the equipment and other
property.
The housing is made of plastic with sensitive electronic components and batteries inside. Safety instructions:
- Do not pierce, break, crush or cut the device or the battery!
- Do not expose the device or battery to open flames or extremely high temperatures!
- Do not expose the device or battery to any liquid or extremely low air pressure!
- Do not drop the device or the battery!
- Do not attempt to replace or charge the battery in the device!
- The device or battery must be recycled or disposed of separately from household waste!
According to the Waste Electrical and Electronic Equipment (WEEE) directive, the device must not be disposed of with household waste. Take the device to a collection point for waste electrical and electronic equipment for proper disposal.
Regulatory guidance for FCC/ISED
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s) and complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation of the device.
Changes or modifications made to this equipment not expressly approved by Aquis Systems AG may void the FCC authorization to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits where designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if they were not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiofrequency radiation exposure information:
This equipment complies with FCC and ISED radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance of 20 cm between the radiator and your body.
Appendix
Technical Drawings IoT Tracking & Monitoring „Schraubmodul“ 
Technical Drawings Battery Module for IoT Tracking & Monitoring
„Schraubmodul“ 
Technical Drawings IoT Tracking & Monitoring „Kompaktmodul“ 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>