OCPP Automatic Paper Cutter Network Port POS Thermal Receipt Printer User Manual

OCPP Automatic Paper Cutter Network Port POS Thermal Receipt Printer

OUTLOOK AND INSTALL PAPER ROLL

Remove the used roll paper core if any,and insert the roll paper. The correct direction of the paper is shown in the illustration below.

CONNECT PRINTER

Button name, indicator LED light and function

Power Indicator:
Light is on means connected properly.

Error Indicator:
When out of paper,cutter or printing head overheat occurred,the ALARM indicator twinkles.

Paper Indicator(LED Light):
Blue and red lights are on means lack of paper, no alarm means all goes well.
Feed Button
Press to feed paper manually.

CONNECT PRINTER

Self Test

Printer connected power and keep off status, then press the “FEED”button and turn on the power, after hear the beeper sounds, release “FEED button”, acompleted self test paper will be printed and show printer settings.

Selftest

• Firmware Version:
• Print Speed: 260mm/s
• Command mode: EPSON(ESC/POS)
• Firmware modify: 2021/07/28
• Cutter enable :Yes
• Beeper enable: Yes
• Black mark mode: No
• Density Level: 5(Max=8)
• Char line FontA/B :48/64
• Default ASCII Font: FONTA
• Default code page: Page0
• Chinese character: No USB&WIFI Interface
• USB port fixed: Yes
• USB Port mode :USB Printing
• MAC address 00-CA-D6-CD-33-25
• IP address: 192, 168.1.100
• Subnet Mask :255.255, 255.0
• Gate Way: 192.168.1.1
• Code page: page 00 stands for PC437(Std. Europe)

Code Page

• 0:PC437(Std. Europe)
• 1:(Katakana)
• 2:PC850(Multilingual)
• 3:PC860(Portugal)
• 4:PC863(Canadian)
• 5:PC865(Nordic)
• 6:(West Europe)
• 7:(Greek)
• 8:(Hebrew)
• 9:(East Europe)
• 10:(Iran)
• 11:(WPC1252)
• 12:PC866(Cyrillic#2)
• 13:PC852(Latin2)
• 14:(PC858)
• 15:(IranII)
• 16:(Latvian)
• 17:(Arabic)
• 18:(PT1511251)
• 19:(PC747)
• 20:(WPC1257)
• 21:(Thai)
• 22:(Vietnam)
• 23:(PC864)
• 24:(PC1001)
• 25:(Uigur)
• 26:(Hebrew)
• 27:WPC1255(Israel)
• 28:PC437(Std. Europe)
• 29:(Katakana)
• 30:PC437(Std. Europe)
• 31:PC858(Mult)
• 32:PC 852(Latin-2)
• 33:PC860(Portugu)
• 34:PC861(Icelandic)
• 35:PC863(Canadian)
• 36:PC865(Nordic)
• 37;PC866(Russian)
• 38:PC855(Bulgarian)
• 39:PC857(Turkey)
• 40:PC862(Hebrew)
• 41:PC864(Arabic)
• 42:PC737(Greek)
• 43:PC851(Greek)
• 44:PC869(Greek)
• 45:PC928(Greek)
• 46:PC772(Lithuanian)47:PC774(Lithuan)
• 48:PC874(Thai)49:WPC1252(Latin1)
• 50:WPC1250(Latin-2)
• 51:WPC1251(Cyril)
• 52:PC3840(IBM-Russian)
• 53:PC3841(Gost)
• 54:PC3843(Polish)
• 55:PC3844(CS2)
• 56:PC3845(Hungarian)
• 57:PC3846{Turkish)
• 58:PC3847(Brazil-ABNT)
• 59:PC3848(Brazil)
• 60:PC1001(Arabic)
• 61:PC2001(Lithuan)
• 62:PC3001(Estonian-1)
• 63:PC3002(Eston-2)
• 64:PC3011(Latvian-1)
• 65:PC3012(Latv-2)
• 66:PC3021(Bulgarian)
• 67:PC3041(Maltese)
• 68:PC852(Croatia)
• 69:VISCII
• 70:WPC1256(Arabic)

INSTALL DRIVER

USB port driver installation

1. Double-click “POS Printer Driver V8.11”
2. USB driver installation or Serial port driver installation
3. Select USB port and printer type
4. Click Start Installation.
5. Select OK.
6. Select YES to print the test page and check the printer driver name;
7. Installation is complete.

WIFI driver installation

1. Double-click “Printer Test V5.1C”
2. WIFI driver installation
3. Insert USB cable, select USB connection, and select “Advanced”
4. Select network settings.
5. Set the IP of the printer WiFi (note that the IP needs to be set in the same gateway as the home network), and the printer is connected to the home network;
6. Use “POS Printer Driver V8.11” to install the driver, select the network port, printer type and IP port number;
7. Click Start Installation.
8. Select YES to print the test page and check the printer driver name;
9. Installation is complete.

TROUBLESHOOTING

Cutter stuck maintenance

• Method (1)
  Turn off the power and then restart.

• Method (2)
  Turn the gear on printing head, cutter can be returned to its original position.

Notice: To avoid the damage of the printing head and automatic paper cutter, please do not open cutter and mechanism violently.

CLEARANCE AND MAINTENANCE

Clearance
One of the following occurred, please clean printing head.

1. The printing is not clear.
2. Any vertical is not clear.
3. Paper feed noisily.

Printing head cleaning steps

Notice

1. Please make sure the power off when maintaining printer.
2. don’t touch or scratch the printing head surface,roller and sensor.
3. Avoid gas, acetone or another organic solvent.
4. Wait till the alcohol is completely volatilized, close top cover and connect the power again.Try printing self-test to make sure it works properly.

Warning
No part of this manual can be changed without agreement.The company reverses the right to modify the technologic, components, software, and hardware. You may ask the distributors for more product information.No part of chapter in this manual can be copied or transmitted in any format without permission.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

References

• information.no

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>