BOSS B6ABY 6.5Inch 2 Way Amplifierd Marine Powersports Roll Cage Waketower Speaker Pods User Manual

BOSS B6ABY 6.5Inch 2 Way Amplifierd Marine Powersports Roll Cage Waketower Speaker Pods

B6ABT
6.5” (165 mm) 2-Way Marine/ Powersports Roll Cage/ Wake tower Speaker Pods

Congratulations on your purchase of a product.

It has been engineered to bring you the highest level of performance. Its quality will afford you years of listening pleasure.

Thank you for making your choice for audio entertainment!

Specifications

• Mid Bass Driver:
  6.5” (165 mm )
  Poly injection cone
  Rubber surround

• Tweeter:
  1” (25 mm) PEI dome tweeter

• Crossover network:
  Built-in

• Impedance:
  4 Ohms

• Frequency Response:
  140Hz – 20kHz

• Sensitivity :
  93dB (1 watt/1 meter)

• Dimensions (W x H x D):
  .19” x 9.88” x 7.31” (182 x 250 x 186 mm)

• Weight (in gift box):
  10.7 lbs. (4.85 kg)

• Amplifier:
  Input Impedance: 10kΩ
  Frequency Response: 20Hz – 20kHz

• Bluetooth:
  Version: 5.0 w/ EDR A2DP
  Range: 33ft (10m)
  Network Name: BOSS Audio Systems B6ABT
  

Introduction

Your new B6ABT wake tower speakers are high-power, fully-waterproof 2-way systems featuring 6.5” drivers and a 1” PEI dome tweeter.

**** understands that wake tower speakers are used in many different types of installations. Our versatile mounting solutions give you the ability to attach our wake tower speakers to mounting tubes with diameters of 1.5” – 2” (38 – 51mm).

What is included?

Before you begin installation, please check that your product contains the following contents:

• 2) Speaker pods
• (4) 130x14x2mm rubber mounting strips
• (4) 120x14x1mm rubber mounting strips
• (2) 48x30x2mm rubber mounting pads
• 4) 2″ mounting aluminum bands for 2″ and 1.875″ installation.
• (4) 1.75″ mounting aluminum bands for 1.75″ and 1.5″ installation.
• (4) M6 locknuts
• (4) M6 flat washers
• 4) M6x60mm screws
• (1) Power/speaker wire harness
• (1) 3.5 mm audio cable

Safety considerations when installing

Please remember that these are heavy products that will be installed in a boating environment. These vehicles can travel at high speeds and be unstable. So please consider this and use extreme caution.

Some safety considerations include:

1. Do not mount the speakers in a location where someone may either walk into or strike their head. During a turbulent ride, please make sure that you do not loosen footing and fall or hit the unit, or it may cause injury.
2. Secure the wires to the speakers in multiple locations along their route to your audio source, so that there are no hanging loops of wire. Having unsecure wires in any hanging conditions can cause entanglement and injury.
3. Tighten the aluminum bands with rubber inserts using care. Do not over compress the rubber inserts. After installation is complete, please recheck all bolts and tighten them further if needed before taking your boat or vessel out for an audio adventure.
4. Do not install these speakers where they may block the view of the pilot and prevent safe operation of the vessel or vehicle.

Installation instructions

STEP.1

To adjust the mounting angle, loosen the metal base of the mounting band by unbolting the two screws.
Make sure to put all components of the mounting hardware in a safe location.

STEP.2

Twist the metal base to determine the optimal mounting angle for the speaker on the cage bar. Then secure the metal base  by tightening the two screws.

STEP.3

Place a supplied rubber pad (48 x 30 mm) on the metal base of the mounting band to prevent abrasion and secure clamping.

STEP.4

Place two supplied rubber strips around the cage bar to prevent abrasion and secure clamping.
Then push two supplied aluminum bands over the cage bar, and align the aluminum bands with the metal base on the speakers.

STEP.5

As illustrated, secure the aluminum bands to the metal base using a pair of M6 x 60mm screws,M6 flat washers, and M6 locknuts. The locknuts must be installed into the hex shaped recess on one end of each aluminum band.
Hand-tighten the screws to the degree which allows just enough freedom to rotate the speaker around the cage bar.

STEP.6

Speaker installation now completes.

Bluetooth

Through Bluetooth connection, you can stream music from a Bluetooth device (e.g. a mobile phone) to the speakers. Make sure Bluetooth is enabled on the device. When the device is in Bluetooth range, it will connect Bluetooth automatically and will be disconnected when it is out of Bluetooth range.

AUX input

Using the supplied 3.5mm audio cable, connect the speaker to your mobile phone for audio input to the speakers. Make sure Bluetooth connection is not made to enable AUX input.

Product dimensions

Wiring

1. Connect the RCA plugs (red/white) to an external amplifier for audio output.
2. Connect the ACC wire (red) to the accessory power of the vehicle as ON/OFF switch of the speakers.
3. Connect the remote out wire (blue) to an external amplifier as ON/OFF switch of the amplifier.

BOSS Audio Systems
3451 Lunar Court• Oxnard, CA 93030
www.bossaudio.com
805-751-4853 Customer Service
Tech Support:www.bossaudio.com/support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>