HILTI R 6-22 Jobsite Radios Instruction Manual

HILTI R 6-22 Jobsite Radios

Original operating instructions

Information about the documentation

About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons.

Explanation of symbols

Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:

DANGER : Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING : Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION : Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the equipment or other property.

Symbols in the operating instructions
The following symbols are used in these operating instructions:

Symbols in illustrations
The following symbols are used in illustrations:

Product-dependent symbols

Symbols on the product
The following symbols can be used on the product:

Product information

HILTI products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use. The type designation and serial number are printed on the rating plate.

• Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

• Radio R 6-22
• Generation 01
• Serial no.

Declaration of conformity

The manufacturer declares, on his sole responsibility, that the product described here complies with the applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany

Safety

General safety instructions

ATTENTION! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Keep these instructions in a handy yet secure place.

Workplace

• Ensure that the workplace is well lit.
• Do not tamper with or attempt to make alterations to the appliance.
• The appliance is not intended for wall mounting.
• Keep your work area clean and well lit. Cluttered or poorly lit work areas invite accidents.

Personal safety

• This product is not intended for use by persons (including children) with physical, sensory or mental disabilities or persons lacking the appropriate experience and/or knowledge. These persons must receive instruction in safe handling of the appliance and must be supervised throughout their use of the appliance by a responsible person.
• Explain to children that they are not allowed to play with the appliance.
• Children over 8 years of age must receive instruction in safe handling of the appliance and must be supervised throughout their use of the appliance by a responsible person.
• Do not wear jewelry such as rings or chains. Jewelry could cause a short circuit resulting in personal injury in the form of burns.
• Avoid touching the contacts.

Battery use and care

• Observe the special guidelines applicable to the transport, storage and use of Li-ion batteries.
• Do not expose batteries to high temperatures, direct sunlight or fire.
• Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.
• Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height or show signs of damage. In this case, always contact your Hilti Service.
• If the battery is too hot to touch it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Contact Hilti Service.

Service
Have the appliance serviced by a qualified repair person using only genuine Hilti spare parts. The safety of the appliance can thus be maintained.

Battery use and care

• Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
• Use only batteries that are in perfect working order.
• Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely harmful to health!
• Do not under any circumstances modify or tamper with batteries!
• Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
• Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of damage.
• Never use recycled or repaired batteries.
• Never use the battery or a battery-operated power tool as a striking tool.
• Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This can lead to explosions.
• Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and also cause material damage and personal injury.
• Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire and explosions.
• Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
• Do not use or store the battery in explosive environments.
• If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the document entitled “Instructions on safety and use for Hilti Li-ion batteries”.
• Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. page 21
• Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these operating instructions.

Description

Overview 1

1. Display
2. Power button
3. Carrying handle
4. Antenna
5. Knob
6. Casing
7. Rubber armoring
8. Mode button
9. Preset button
10. Bluetooth button
11. Equalizer button
12. Time settings
13. USB port
14. AUX port
15. Battery
16. NFC interface
17. Battery compartment

Intended use

The product described is a cordless jobsite radio. It is designed for playing music as a radio receiver or from various other devices that can be either paired with the product via Bluetooth or connected to it by an AUX cable.

• The product is designed for a jobsite environment. Do not expose the product to moisture such as running water, for example.
• Use the product only indoors.
• For this product, use only Hilti lithium­ion batteries of the B 22 series. For this product, Hilti recommends the use of the batteries stated in the table at the end of these operating instructions.
• For these batteries, use only Hilti chargers of the type series listed at the end of these operating instructions.

Items supplied

Jobsite radio, AAA batteries (2 of), operating instructions. Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group

Bluetooth
This product is equipped with Bluetooth (optional). Bluetooth is a wireless data transfer system by which the two Bluetooth-enabled products can communicate with each other over a short distance.

Status indicators of the Li­ion battery

Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery’s state of health.

Indicators for state of charge and fault messages

WARNING: Risk of injury by a falling battery!
If the release button is pressed with a battery inserted in the product, subsequently check that the battery is correctly re-engaged and secure. Short- press the release button of the battery to get whichever of the following status indications is applicable at the time. State of charge and, if applicable, faults are indicated constantly as long as the connected product is switched on.

Recharge the battery.

If the LED again starts quick-flashing after the bat- tery has been charged, consult Hilti Service.

One (1) LED quick-flashes yellow| The Li-ion battery or the product in which it is in- serted is overloaded, too hot or too cold, or experi- encing some other fault.

Bring the product and the battery to the recom- mended working temperature and do not overload the product when it is in use.

If the message persists, consult Hilti Service.

One (1) LED shows yellow| The Li-ion battery and the product in which it is inserted are not compatible. Consult Hilti Service.
One (1) LED quick-flashes red| The Li-ion battery is locked and cannot be used. Consult Hilti Service.

Indicators showing the battery’s state of health
To check the battery’s state of health, press the release button and hold it down for longer than three seconds. The system does not detect a potential malfunction of the battery due to misuse, for example battery dropped or pierced, external heat damage, etc.

The battery can remain in use.
All LEDs show in sequence, followed by one (1) LED quick-flashing yellow.| The check to ascertain the battery’s state of health did not complete. Repeat the procedure, or consult Hilti Service.
All LEDs show in sequence, followed by one (1) LED showing constantly red.| If a connected product can still be used, the re- maining battery capacity is below 50 %.

If a connected product can no longer be used, the battery has reached the end of its useful life and has to be replaced. Consult Hilti Service.

Information shown in the display

Information shown in the display → page 17

Information shown in the display

Cradle for mobile devices 14
Via Bluetooth or AUX, the radio can play audio from external mobile devices (such as smartphones or tablet computers). The mobile devices can be cradled securely on the radio.

Technical data

Product properties

Bluetooth

Battery

Preparations at the workplace

WARNING: Risk of injury by inadvertent starting!

• Before inserting the battery, make sure that the product is switched off.
• Remove the battery before making any adjustments to the power tool or before changing accessories. Observe the safety instructions and warnings in this documentation and on the product.

Charging the battery

1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 15

Inserting the battery

WARNING: Risk of injury by short circuit or falling battery!

• Before inserting the battery, make sure that the contacts on the battery and the contacts on the product are free of foreign matter.
• Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.

Removing the battery

1. Press the battery release button.
2. Remove the battery from the product.

Inserting the back-up batteries 2
It is not possible to save settings unless the batteries are correctly installed. Make sure that battery polarity is correct.

1. Remove the cover from the battery compartment.
2. Insert the 2 AAA batteries supplied with the appliance into the battery compartment.
3. Install the cover on the battery compartment.

Switching the appliance on / off 3

Press the Power button.

Operation

Observe the safety instructions and warnings in this documentation and on the product.

Establishing a Bluetooth connection 4
If you are prompted for a code, enter the code 0000.

1. Press the Bluetooth button.
2. To initially pair the radio manually, press the Bluetooth button and hold it down for 2 seconds.
   • The Bluetooth symbol flashes.
   • Select the Hilti radio on the mobile device.
   • The devices have been successfully paired when the Bluetooth and pairing symbols both show continuously in the display.
3. If the radio has already been paired to the mobile device, press the Bluetooth button.
   • Pairing starts automatically and the pairing symbol on the screen starts to flash.
   • The radio searches for a signal for a maximum of 3 minutes.
   • The pairing symbol appears on the display to indicate that the devices are paired.
   • The Bluetooth symbol appears in the display to indicate that the radio has found a paired mobile device.
4. If you have a second radio, you can synchronize the two radios and listen to music in stereo.
   • Radio (A) is connected to your mobile device. This radio is the master.
   • Switch radio (B) on.
   • On radio (B), press the Bluetooth button.
   • On master radio (A), press the Preset button (an acoustic signal sounds to confirm that the connection has been established).
   • Shortly after, music will start playing in stereo on the two radios.

Making an NFC connection 5

1. Activate the NFC function on your mobile device (if it supports NFC).
2. Hold you mobile device close to the NFC interface of the radio. This is on the right-hand side and is indicated by the NFC symbol.
   You must accept the NFC connection on your mobile device when the connection is established for the first time.

Setting the audio source 6

1. Press the mode button.
2. Select the desired audio source.
   You have a choice of AM, FM, AUX, Bluetooth and DAB.

Searching for and saving stations 7
Quickly turn the knob a short distance to start the automatic station search.

1. Use the knob to select a frequency.
2. Press the ‘Preset’ button.
3. Press the knob to save this frequency.

Positioning the antenna 8
Swivel the antenna to the position at which reception is clearest.

Adjusting the volume 9

1. Turn the power button clockwise to increase the volume.
2. Turn the power button counterclockwise to reduce the volume.

Equalizer settings 10
This allows you to make adjustments to the bass and treble settings.

1. Press the equalizer button (EQ).
2. Use the knob to select either bass or treble for adjustment.
3. Use the knob to change your settings.

Audio playback from a mobile device via Bluetooth
For good audio quality, set the volume of the external device to very high. Further adjustment of the volume should then be made using the controls on the appliance.

1. Establish a Bluetooth connection between the mobile device and the radio.
2. Select the play mode (Bluetooth).
3. Press the Start/Pause button on your mobile device or press the knob to start or pause audio playback.
4. Use the arrow buttons on the mobile device or turn the knob to change tracks and to start.

Audio playback from an external device via AUX 11
For good audio quality, set the volume of the external device to very high. Further adjustment of the volume should then be made using the controls on the appliance.

1.  Select the play mode (AUX or Bluetooth).
2. Press the start/pause button on your mobile device to start or pause audio playback.
3. Use the arrow buttons on the external device to change tracks and to start.

Setting the clock 12
Automatic synchronization of clock time with radio time can be switched on or off.

1. Press the clock button.
2. Use the knob to set the time.
3. Save the time by pressing the knob briefly.
4. Use the knob to select whether you wish to synchronize the time and press the knob briefly to confirm your choice.

USB charging function 13
The USB connector provides charging power only. Data transfer is not possible. Use a USB cable to connect your mobile device to the USB port of the radio.

Care and maintenance

WARNING: Risk of injury with battery inserted!
Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.
• Carefully clean the air vents, if present, with a dry, soft brush.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
• Use a dry, clean cloth to clean the contacts of the product.

Care of the Li­ion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.
• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of moisture (e.g. by being dipped in water or left in the rain). If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable container and consult Hilti Service.
• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents containing silicone as these can attack the plastic parts. Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product repaired by Hilti Service.
• After cleaning and maintenance, install all guards and protective devices and check that they are in full working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with your product can be found at your Hilti Store or online at: www.hilti.group

Transport and storage of cordless tools and batteries

CAUTION: Accidental starting during transport !

• Always transport your products with the batteries removed!
• Remove the battery/batteries.
• Never transport batteries loose and unprotected. During transport, batteries should be protected from excessive shock and vibration and isolated from any conductive materials or other batteries that may come in contact with the terminals and cause a short circuit. Comply with the locally applicable regulations for transporting batteries.
• Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged batteries.
• Prior to each use and before and after prolonged transport, check the product and the batteries for damage.

Storage

WARNING: Accidental damage caused by defective or leaking batteries !

• Always store your products with the batteries removed!
• Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in the technical data.
• Do not store batteries on the charger. Always remove the battery from the charger when the charging operation has completed.
• Never leave batteries in direct sunlight, on sources of heat, or behind glass.
• Store the product and batteries where they cannot be accessed by children or unauthorized persons.
• Prior to each use and before and after prolonged storage, check the product and the batteries for damage.

Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, contact Hilti Service.

a new battery.
Battery defective| ▶ Check the battery by pressing the two buttons at the sides. If the LEDs light up the radio might be defective. If the LEDs do not light up the battery is defective.

▶ Contact Hilti Service.

Radio defective| ▶ Contact Hilti Service.
Border of the battery symbol flashes, no segment of the state of charge indicator filled (the indicator assumes this state for a short time before the appliance switches itself off).| Battery too hot| ▶ Wait until the battery cools down.
Battery too cold| ▶ Wait until the battery warms up.
Battery defective| ▶ Check the battery by pressing the two buttons at the sides. If the LEDs light up the radio might be defective. If the LEDs do not light up the battery is defective.

▶ Contact Hilti Service.

Settings such as clock time are no longer saved in mem- ory.| Batteries discharged| ▶ Replace the back-up batteries.

Disposal

WARNING; Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.

• DO NOT send batteries through the mail!
• Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.
• Dispose of your battery out of the reach of children.
• Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public health and safety resources for disposal instructions.

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information. Do not dispose of power tools, electronic equipment or batteries as household waste!

Manufacturer’s warranty
Please contact your local Hilti representative if you have questions about the warranty conditions.

Further information
For more information on operation, technology, environment and recycling, follow this link: qr.hilti.com/manual?id=2309424
This link is also to be found at the end of the operating instructions, in the form of a QR code.

References

• HILTI Country selector
• Главная страница - Hilti Россия

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>