Linmore LED Ace LED Panel (AP1) Instruction Manual
- June 3, 2024
- Linmore LED
Table of Contents
Ace LED Panel (AP1)
Instruction Manual
Ace LED Panel (AP1)
READ CAREFULLY BEFORE INSTALLING FIXTURE.
PLEASE KEEP THIS MANUAL FOR FUTURE USE.
Fixtures must be wired in accordance with the national electrical code and all
applicable local codes.
Proper grounding is required for safety.
This product must be installed in accordance with the application code by a
person familiar with the construction and operation of the product and the
hazards involved. Make certain power off before installing or maintaining
fixture.
Check that voltage is compatible with fixture driver, use approved connectors
for all electrical connections
LED panel not suitable for using in wet locations.
Please keep the LED panel away from any corrosive substance, and please use
dry cloth when you clean it.
WARNING
Risk of Fire or Electric Shock
Risk of fire or electric shock. Make sure power supply is off before
installing or maintaining the product.
Risk of fire or electric shock. Install this product only in the luminaires
that have the construction features and dimensions shown in the photographs
and/or drawings and where the input rating of the product does not exceed the
input rating of the luminaire.
Install the recessed troffer only in 15/16” NEMA type G or type NFG t-grids
with a minimum troffer depth of 3”.
Risk of fire or electric shock. To prevent wiring damage or abrasion, do not
expose wiring to edges of sheet metal or other sharp objects.
Risk of fire or electric shock. Installation guide requires knowledge of
luminaire electrical systems. If not qualified, do not attempt installation.
Contact a qualified electrician.
Risk of fire or electric shock. Only those open holes indicated in the
photographs and/or drawings may be made or altered as a result of kit
installation. Do not make or alter any open holes in an enclosure of wiring or
electrical components during installation.
Risk of fire or electric shock. Never perform maintenance or cleaning while
fixture is energized. Disconnect power and allow fixture to cool before
maintaining.
Risk of injury. Wear safety glasses and gloves during installation and
servicing.
MAINTENANCE CAUTION
- Review the diagrams before beginning and make sure the fixture is grounded properly.
- For lighting controls, use driver wiring diagram.
- Turn power off and wait for fixture to cool.
- Maintenance must be done by qualified electricians.
TECHNICAL SPECS
Part No.| Power| Working
Current| Input
Voltage| Efficacy| CCT| Viewing
Angle| CRI| PF| Dimmable| Warranty
---|---|---|---|---|---|---|---|---|---|---
AP10S-A2-ADJ-14-ADJ-80-FR
-LV-GRID-[xxx]-10V| 30W /
35W /
40W| 0.44A| AC
120-277V| 125 LPW| 3500K /
4000K /
5000K| 120°| ≥80| ≥0.9| 0-10V| 5 Years
AP10S-A2-ADJ-22-ADJ-80-FR
-LV-GRID-[xxx]-10V| 30W /
35W /
40W| 0.44A
AP10S-A2-ADJ-24-ADJ-80-FR
-LV-GRID-[xxx]-10V| 30W /
40W /
50W| 0.55A
INSTALLATION GUIDE
- Unscrew the driver cover.
- Connect the conduit to the driver box.
- Connect other wires separately.
- Put back the driver cover and fix it by screw.
Fixture comes set to 4000K CCT from the factory.
Recessed Installation
- Replace existing lighting fixture from ceiling with LED Panel.
- Use the protective brackets for safety.
Suspension Kit Installation
- Drill two holes in the ceiling and put the anchors into hole, then insert the wire rope and screw.
- Adjust the hanging rope, placing the panel in a horizontal position.
- The installation is finished. Note: Suspended ceiling mount kits needed for installation, sold separately.
Linmore LED Labs, Inc
2360 S Orange Ave, Fresno CA 93725
559-485-6010
linmoreled.com
info@linmoreled.com
Documents / Resources
|
Linmore LED Ace LED Panel
(AP1)
[pdf] Instruction Manual
Ace LED Panel AP1
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>