NetBee 18V 5.0 Ah Socket Tray Instructions

18V 5.0 Ah Socket Tray Instructions
OPERATING INSTRUCTIONS

Operating principles

Dear customers,
thank you for choosing a HS-Technik GmbH product.
This quality product „Made in Germany“ fulfils the highest requirements with regard to performance, quality and accuracy. When used correctly the product will undoubtedly
perform very well for many years.
These operating instructions contain information on safety and for the operation of the NetBee. In addition it contains information on the dimensions and technical data. We
would be happy to assist you with additional information or to answer your questions. Our technical support and our technicians would be happy to assist you.
1.1 Aim
This manual is a complete guide for the NetBee Socket Tray, describing how to use.

1.2 NetBee Product Safety
WARNING
Before using the product, read the NetBee Socket Tray Product Safety manual and strictly follow the safety instructions.
1.3 Reference documents
To have a complete view of the NetBee Socket Tray applications, refer also the following HS-Technik GmbH documents:

• NetBee Product Safety
  NetBee User Manual

1.4 Warranty Safety
Contact HS-Technik GmbH to claim a product. Warranty is applied only if the product has been installed, operated and overhauled according to the instructions provided with the product.
Please also see the delivery conditions applied by the HS-Technik GmbH.

Specifications

2.1 Technical
Sockets

Depending from the model:

• 6 sockets, 39 mm
• 6 sockets, 50 mm
• 8 sockets, 39 mm

Power supply
Models CANBUS and ETHERNET
The External power supply must be provided as following:

• Pin 3: +24VDC, maximum current 800 mA
• Pin 4: GND

Power Supply connector view from outside

Canbus connector view from outside
The mating connectors are delivered with the NetBee Socket Tray.
Models WiFi
Rechargeable battery (HST-PR-1850 18 V 5.0 Ah, Li-Ion) for models WiFi. Battery last for at least 8 hours.
2.2 Dimensions / Weight
Dimensions are in millimeters. Customized NetBee Socket Tray versions may have different dimensions.
NetBee Socket Tray WiFi

NetBee Socket Tray CANBUS / Ethernet

2.3 Environmental
The following conditions must be observed during operation:

• Internal Use only
• Environmental Class: II
• Ambient Temperature: 5 to 40°C
• Atmospheric humidity: 95%, non-condensing
• Altitude: Up to 2000m
• IP grade: IP 40

Function

The NetBee Socket Tray is designed to manage the sockets used on tools and wrenches.

Operation mode:

• All the sockets must be present on the tray.
• Only one socket must be taken at a time, according to the parameter (socket number) ofthe tightening operation.
• If the wrong socket is taken, the tightening operation is not started.

NetBee

• NetBee defines the sequence of the assembly process, and checks that the operator takes the correct socket from the tray

Refer to the NetBee user manual for more information.
NOTE
The NetBee Socket Tray does not start automatically a tightening operation or a sequence when the socket is removed from the tray. NetBee starts the operation and makes a check on the socket.

The NetBee Socket Tray connected to NetBee via WiFi

The NetBee Socket Tray connected via WiFi

The NetBee Socket Tray connected to NetBee via Ethernet

The NetBee Socket Tray connected via Ethernet

The NetBee Socket Tray connected to NetBee via Canbus
3.1 Models
The NetBee Socket Tray can be delivered in the versions:
WiFi: Wireless communication, working with:

• NetBee

Ethernet: Ethernet communication

• NetBee

Canbus: Canbus interface (for NetBee only), working with:

• NetBee

Sockets configuration can be:

• 6 sockets 39 mm
• 6 sockets 50 mm
• 8 sockets 39 mm

3.2 Equipment configuration

1. Sockets
2. LED (one per socket)
3. Sensor position adjustment

3.3 Main parts
Socket and LED
Place where the socket is placed: LED ACTIVE: Socket not present.
LED BLINK: Indicates the socket that must be used for the tightening program.
When the NetBee Socket Tray is switched on, the LEDs are activated in sequence.
The position of the sensor can be adjusted to suit the sockets used:

To be detected, sockets must be metallic.
Normally the cap is used with a customized hole to match the shape of the socket (in the figure above the cap is shown as “new”, without any hole on top):

To remove the caps, remove the 4 screws and pull the bars:

The grain and nut are used to provide friction to the socket used, especially in applications where the socket tray is mounted on a moving cart.

Battery
For NetBee Socket Tray WiFi version only, which is powered by external battery

Ethernet port
For NetBee

Canbus interface
For NetBee Socket Tray version Canbus, this connector is available

See the Technical chapter for more information about pinout of the connector.

Power supply

For Ethernet and Canbus versions only

See the Technical chapter for more information about pinout of the connector.

NetBee Socket Tray Configuration

The NetBee Socket Tray, when first received, must be configured to work in the specific network of the user (not for Canbus models).
The NetBee Socket Tray are configured, by default, as following:
NetBee Socket Tray WiFi:

• SSID: Tecnogi1
• Password: Codrus65
• IP: 192.168.1.5
• Mask: 255.255.255.0

NetBee Socket Tray Ethernet:

• DHCP
• IP Address: 192.168.1.5

The programming software CB Config is delivered with the NetBee Socket Tray. Launch the software. The following window is shown:

NetBee Socket Tray WiFi Configuration
Switch off the NetBee Socket Tray and open the chassis, removing the 4 screws:

Set the internal DIP switches to ON:

Switch on the NetBee Socket Tray. With the configuration software above, set the new network parameters and save. Switch off the NetBee Socket Tray. Set the DIP switches to OFF:

Close the NetBee Socket Tray chassis with the 4 screws.
NetBee Socket Tray General Configuration

The panel with Sockets (input) and LEDs (output) status is a monitor of the sockets status and it is possible to activate the LEDs manually (useful for testing).
The number of sockets and LEDs in the panel matches those available on the NetBee Socket Tray.
The NetBee Socket Tray is delivered already configured. In special applications, it might be necessary a customized configuration, using the INSERT menu in the window above. In that case, HS-Technik GmbH will provide dedicated instructions. Otherwise, it is strongly recommended not to change the parameters in the INSERT menu.

NetBee Socket Tray Maintenance

The NetBee Socket Tray does not require a specific maintenance. Keep the NetBee Socket Tray clean and verify the LEDs are working when the NetBee Socket Tray is  powered on. For WiFi models, refer to the battery manufacturer manuals for battery instructions and maintenance.

HS-Technik GmbH
Im Martelacker 12
D-79588 Efringen-Kirchen
Telephone: +49 (0)7628 – 91 11-0
Fax: +49 (0)7628 – 91 11-90
E-Mail:info@hs-technik.com
Internet: www.hs-technik.com
The technical data in this printed material provide guidance, but are without guarantee!
We reserve the right to make structural changes. Our construction suggestions are not bind

Documents / Resources

| NetBee 18V 5.0 Ah Socket Tray [pdf] Instructions
18V 5.0 Ah Socket Tray, 18V 5.0 Ah, Socket Tray
---|---

References

• BRANDED | Brand Creation & Implementation Agency
• HS Technik – High – System – Technik

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>