D4S BASSBUDZ STUDIO1 Wireless ANC Headphones User Manual

D4S BASSBUDZ STUDIO1 Wireless ANC Headphones

WHAT’S IN THE BOX

POWER ON/OFF

Power ON:
Press and HOLD the Power button until the Status Indicator lights BLUE.
Power OFF:
Press and HOLD the Power button until the Status Indicator turns off.

NOTE
If not connected to a Bluetooth-enabled device for 5 minutes, or the AUX cable is unplugged, the will automatically power off .

BLUETOOTH PAIRING
Power on the device and follow the steps below to pair with your Bluetooth enabled device.

1. Press and HOLD the Bluetooth button until Status Indicator flashes red and blue, the voice prompt “Bluetooth airing on will be heard.
   To exit Bluetooth pairing mode, press and quickly release the Bluetooth button.

2. Open your device’s Bluetooth menu.

3. Find and select to pair.

4. Once paired, the voice prompt “Connected” will be heard and the status Indicator will flash BLUE every five seconds.

ANC (ACTIVE NOISE CANCELLATION) MODES

The ANC modes offer 3 differernt listening

1. Noise Cancelling (NC) Mode:
   Green LED
   This mode isolates your listening experience specifically to sound coming through the headphones and helps blocking unwanted outside noise.
   NC mode is automatically activated by default when the headphones are powered on. When NC mode is active, the Status Indicator turns solid green.

2. Advanced Transparency Mode
   White LED
   Advanced Transparency allows you to listen to the sounds around you through the built-in microphones even while using the headphones.
   To enter Advanced Transparency, press the ANC button once and the voice prompt “Ambient sound ” is heard, the Status Indicator of the headphones will turn solid WHITE.
   Note: Advanced Transparency allows you to hear background noise clearer Such as important announcements and street traffic. However, certain sounds may not be heard well depending on the environment. Be cautious in places where an inability to hear ambient SOund would be dangerous.

3. Advanced Transparency and NC OFF: LED OFF
   Press the ANC button once more and the voice prompt “ANC mode & ambient sOund off” is heard, the Status Indicator indicator will turn off.

To turn NC mode back on, press the ANC button again.

Instant Awareness Mode

Place the palm of your hand over the right earcup, the music is muted until you release your palm trom the earcup.

TOUCH CONTROL (TOUCHPAD OPERATION)
The headphones include a multifunction touchpad located over the right earcup.
Use the following gestures to Control audio playback and answer calls.

Manual Volume Control:
To manually increase or decrease the volume, place your fhinger at either the top or bottom of the earcup as shown, and slowly swipe up or down as shown bellow.

PLAY MUSIC

Play/Pause: Double tap the centre of the touchpad quickly  to play or pause music

Answer an Incoming Call:
Double tap quickly to answer the call.

End an ongoing call:
Double-tap quickly to end an ongoing call.

Rejectinga Call
Touch and Hold during an incoming call to reject a call.

Voice Assistant:
Touch and HOLD until the default voice assistant of your device is activated. You Can touch and HOLD again to cancel.
(Depending on your phone this may be Siri or Google.)

CHARGING
Insert the USB Type-C cable into the USB port of the headphones as shown below and connect the other end to a USB Charger or charging device. Charge Indicator will turn solid RED while charging and become solid GREEN when fully charged.
While charging, the headphones cannot be powered on or used.

Note: When the battery is lOw, the Status Indicator flashes red twice every 5 seconds and the “Opps, battery low” voice prompt will be heard.

USING THE AUDIO CABLE
When connecting the 3.5mm AUX cable to the tracks must be controlled trom the source device.
When you unplug the AUX cable and are not connected via Bluetooth the headphones will power down.
It you want to use Noise Canceling or Transparency without Bluetooth, please ensure the AUX cable is plugged in. the volume and LED INDICATORS
The headphones include two indicators, the Status Indicator and the Charge Indicator.
Both LED indicators are explained below.

LED INDICATORS
The headphones include two indicators, the Status Indicator and the Charge Indicator Both LED indicators are explained below.

Status Indicator

Bluetooth

Charge Indicator

Charging

Warranty service terms

1. The product has any function problem, can enjoy the warranty service,the warranty period limits 1 year.
2. Artificial damage, fall, artificial scratch, no warranty repair card is not within the scope of warranty.
3. Customer must fill in the necessary information(name, address, telephone number, date of purchase).
4. We are not responsible for the cost of the locks during the warranty period.
5. The warranty service must have the warranty card and can be operated according to the requirement, otherwise no warranty.

Product Model:
Customer name:
Contact number:
Customer Address:
Purchase date:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>