SEALEY CS20V 20V Cordless Strimmer User Guide

SEALEY CS20V 20V Cordless Strimmer

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• Always wear appropriate eye protection, ear protection, substantial footwear, gloves, long trousers whilst operating.
• Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
• Inspect and ensure equipment is in good working order before use.
• Maintain and clean tool and battery pack, regularly. Check air holes are clear.
• Must be serviced by an authorised agent. Use genuine parts only. Non authorised parts will invalidate the warranty.

WARNING! Remove battery before: performing maintenance, carrying out adjustments, inspecting the machine after striking an object, before clearing a blockage, before leaving the tool unattended, before moving to the next job location.
WARNING! Risk assess the work area. Keep bystanders away from the work area.

• DO NOT operate with anyone or pets nearby. Check intended work area for wildlife.
• DO NOT use in bad weather conditions, especially when there is a risk of lightning. DO NOT expose to rain. Only use in good light.
• DO NOT use if tool vibrates abnormally, switch off, remove battery and then inspect.
• DO NOT touch hazardous moving parts. Allow to come to a complete stop first.
• DO NOT operate whilst tired, ill under the influence of alcohol or other intoxicating drugs.
• DO NOT overreach and keep balance at all times.
• DO NOT use if damaged. DO NOT operate with defective guards or shields or without safety devices.C
• DO NOT use for a task it was not designed to perform.
• Store with the battery removed and separate from the machine, in a dry, childproof location.

WARNING! Never allow children, persons with reduced physical sensory or mental capabilities or lack of experience and knowledge or people unfamiliar with these instructions to use the machine, local regulations may restrict the age of the operator.

INTRODUCTION

Lightweight cordless strimmer makes gardening easy, clean and effective. Fully adjustable in height and cutting angles. Head can be adjusted vertically between 0°-50° (four settings available). Head can also be rotated between 0°-90° both ways for applications such as lawn edge cutting. Works in conjunction with our one battery fits all program. Body only. (Includes 10 x plastic blades). Requires compatible 20V battery and mains charger, sold separately.

SPECIFICATION

• Model No: ……………………………..CS20V
• Battery: ………..20V 2Ah – 6Ah Lithium-ion (not included)
• Consumable parts: CP20VBP2 – 2Ah Battery, CP20VBP4 – 4Ah Battery, CP20VBP6 – 6Ah Battery
• Cutting Mechanism: ………………….. Plastic Blade
• Cutting Width :……………………………260mm
• No Load Speed: ………………………. 8000rpm
• Replacement parts: . . . . . . . . . . . . . . . . CP20VMC – Mains Charger (not included)
• Voltage: ……………………………. 20V Li-ion
• Noise power ……………………………88dB(A)
• Noise pressure ………………………… 78dB (A)
• Vibration ……………………………….5.8m/s²
• Uncertainty ……………………………..2.3m/s²

ASSEMBLY

FIT SAFETY HOOD
Push the guard hood in the direction of the arrow onto the motor housing as shown in (fig.1).
Make sure it latches in place correctly

FIT EDGE GUIDE

Fit both ends of the edge guide into the lashing eye as shown in (fig.2).

ADJUSTING ADDITIONAL HANDLE

Undo the securing screw on the additional handle to adjust angle (fig.3). Set the required position and tighten the securing screw (fig.3).

ADJUSTING THE HEIGHT

Undo the union nut until the grass trimmer handle can be moved in and out freely. Now set the required working height (fig.4) and secure the handle in this position by tightening the union nut again.

OPERATION

WARNING! Only use this machine for its intended use.
DO NOT use the grass trimmer without the guard.
DO NOT cut grass when it is wet. The best results are achieved with dry grass.
Always wear appropriate eye protection, ear protection, substantial footwear, gloves, long trousers whilst operating.
Push the battery pack into the mount provided (fig.5).
To remove the battery pack, press the battery pack button and pull the battery out.

ADJUSTING THE ANGLE OF TILT OF THE GUIDE HANDLE

Press the button for the angle of tilt adjustment (fig.9). Now set the long handle to the required tilt. Release the button and allow the
handle to lock into position to fix the angle of tilt. Four ditfferent locking angles are possible.
To switch on your grass trimmer press the safety lock-off (fig.6) and then press the On/Off switch (fig.6).
To switch off your grass trimmer, let go of the On/Off switch.
WARNING! The blade will continue to spin fora few seconds after the ON/OFF switch is released.
DO NOT allow the grass trimmer near the grass until the switch is pressed and the grass trimmer is in operation.
To cut properly, swing the machine sideways while moving forwards. Keep the grass trimmer inclined at an angle of approx. 30″ while you do so (fig.7 & 8 ).

USING THE GRASS TRIMMER AS AN EDGE TRIMMER

To cut the edges of lawns and flower beds, the grass trimmer can be converted as follows:
IMPORTANT Remove the battery pack.
Push and turn the motor head through 90° in the required direction until it latches in place (fig.12).
Now the arass frimmer has heen converted to an edae trimmer that cuts verticallv

MAINTENANCE

WARNING! before cleaning the grass trimmer, pull out the battery pack.

CLEANING

Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it down with compressed air at low pressure.
Always clean the equipment immediately after use.
Clean the equipment regularly with a damp cloth and some mild soap. DO NOT use cleaning agents or solvents, these may be aggressive to the plastic parts in the equipment. Ensure that no water can get into the interior of the equipment. The ingress of water into an electric tool increases the risk of an electric shock.
Use a brush to remove deposits from the safety guard.

REPLACING THE BLADE
IMPORTANT Be sure to remove the battery pack before replacing.
To remove the blade, push the blade inwards and remove it through the larger opening as shown (fig.13).
To fit the new blade, proceed in reverse order. Make sure the blade locks into place correctly (fig.14).

STORAGE

Remove battery. Store carefuly in a secure, dry place, out of the reach of children.

WARNING! – Risk of Hand Arm Vibration Injury.

This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): …. ..5.8 m/s
Uncertainty value (k):. …. . . . ….. 2.3 mísS
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each too.
NB: Stated Vibration Emission values are type-test values and are intendeed to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration Syndrome.

Health surveillance.

We recommend a programme of health survellance to detect early symptoms of vibration injury so that management procedures can be modified accordingly.

Personal protective equipment.

We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the HSE website www.hse.gov.uk – Hand-Arm Vibration at Work.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fiuids according to local regulations.

WEEE REGULATIONS

Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
U01284 757 500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

References

• HSE: Information about health and safety at work

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>