KUFATEC VW T5 7H Complete set Active Sound incl Soundbooster Instruction Manual

KUFATEC VW T5 7H Complete set Active Sound incl Soundbooster

Liability Exclusion

Dear Customer Our cable sets are developed according to the connection- and circuit diagrams of the corresponding car manufacturer. Before the original production the cable sets will be tested on an original car. Therefore, the integration into the car electronics will be executed according to the instructions of the manufacturer. Regarding the necessary pre-understanding and the accuracy of the presentation of texts and pictures our mounting guidelines correspond to the usual ones in car technology and car electronics. Practically, they have been proved one’s worth a hundred times. However, should there be any difficulties during the installation of our products we will be at your dis-posal any time for support by phone or by mail. Moreover, we offer you to execute the installation at our works in Bad Segeberg.

Costs which may arise because a third person will execute the installation of our products will not be supported by us in any case. Only if there is a mistake caused by our product we will pay the proved costs of the installation as well as the costs of the removal of the defective product. The refund of expenses will be limited to gross EUR 110,- ; we reserve the right to check the described mistake in our works in Bad Segeberg. In case of a proved reclamation the costs for dispatch for the check in our factory will be transferred to you. According to our experience each specific factory which has the necessary diagnostic device, diagnostic software and the circuit diagrams of the manufacturer can find possible mistakes at our products within a short time.

So the installation and removal including diagnostic inspection can be realised in at most 60 minutes. We also made the experience that many specific factories cannot work with the circuit diagrams of the manufacturer, and that they cannot read usual wiring diagrams. Therefore, very easy installation works will take many hours. You will understand that we neither take the risk to find a reliable specific factory nor the financing of the training of the staff of your favoured factory. Costs which will arise because you buy missing parts or spare parts at other suppliers will be refunded by us up to the amount of the costs which had been arisen by additional supply (saved expenses).

In this case, there would be no right for refund according to the legal guarantee right as long as we have no deadline for supplementary performance or a deadline for supplementary performance has not expired. So if you have any problems with the installation or operation of one of our products please call us, send us an email, send us the product or take your car to our factory in Bad Segeberg. We are sure to find an appropriate solution for each concern. With best regards Your Kufatec GmbH & Co. KG Team

Copy Right

Our installation- and removal instructions, installation plans, software and other documentation with texts or pictures are protected by copy right. A publication or distribution of these documents is only permitted with a written approval of Kufatec GmbH & Co. KG.

General Notes

Regarding the development there has especially been paid attention to your personal safety together with the most possible operating comfort, modern design and actual product technologies. Despite most possible accuracy in case of incorrect installation or use or in case of incorrect operating, it is possible that injuries or damages of property may arise. Therefore, please read the operating instructions you have received carefully and completely, and keep it with you. All articles of our production will be checked at 100% — for your safety. We reserve the right to make technical changes which serve the progress at any time. Before the installation or startup it may be necessary, depending on the article and purpose of use, to check the legal instructions of each country. In case of warranty claim the device has to be sent to the seller originally packed together with the sales receipt and a detailed description of the mistake. Please consider the manufacturer’s instructions for return (RMA). The legal warranty instructions are valid. The warranty claim and also the permission for startup will expire in case of:

• unauthorised changes on the device or the accessories which have not been executed or approved by the manufacturer or its partners
• opening of the box
• repair of the device on your own
• incorrect use / no normal use / startup
• influence of force on the device (falling down, wilful damage, accident, etc.)

During the installation please consider all safety and legal instructions. The device may only be installed by trained qualified personnel or persons who are similar qualified. In case of installation- or function problems please reduce the search of the mistake to approx. 0,5 hours for mechanical works or 1,0 hours for electronic works. To avoid unnecessary additional work and expenses, please send immediately an inquiry to our technical support with the Kufatec contact form (http://www.kufatec.de/shop/de/infocenter/)
Please absolutely mention the following:

• car chassis number
• part number of the add-on kit
• exact description of the problem
• work steps already made

Safety instructions

The installation may only be executed by trained qualified personnel. Please execute the installations only in a condition of dead voltage. Here please separate for example the battery from the main power supply and consider the instructions of the car manufacturer.

• In order to not endanger your own driving safety please never use security relevant screws, bolts or other fixation pieces at steering, brake system or other components.
• Connect the device only at 12V wiring system voltage with ground connection to the autobody. This assembly is not allowed for the use in trucks or other cars with 24V wiring system voltage.
• Please avoid the installation of the device at positions where the driving safety or the functional efficiency of other subassembly integrated in the car are restricted.
• This module may only be used together with the following mentioned car types and models; the instal-lation may be executed exclusively by use of the circuit points mentioned in the assembly instructions.
• Kufatec GmbH & Co. KG does not assume liability for damages which are caused by incorrect installation, the use of inapplicable circuit points or the installation into car types and -modules which are not foreseen.
• We would like to draw your attention to the fact that the module processes the data of the MOST-protocol of the car mentioned below. Therefore, during the installation of the module it will be used a model-specific complete system which we as the manufacturer of the mentioned construction line only know partly.
• Especially in case of changes within the same model line and the same year we therefore cannot guarantee the applicability of our construction line in each case. Kufatec GmbH & Co. KG does not assume liability for the applicability of our construction line with changes made by the manufacturer.
• Kufatec GmbH & Co. KG does not assume liability that the installation of the here described com-ponent has been permitted according to the guarantee instructions of particular car manufacturers. Therefore, please consider the guidelines for installation and guarantee conditions of your car manu-facturer before installation.
• The manufacturer reserves the right to change components without giving reasons.
• Subject to errors and changes

Requirements for the determinable operation

Please use the device only in its the corresponding area. In case of unprofessional and untypical use, installation or modification the permission for operation and the warranty claim will expire.

Note

Make sure that there’s enough space at the described position. If there is no space please cancel the installation and contact our technical support.
The use of a sound booster is not permitted without registration in the vehicle papers, in the area of the german StVZO. The noise emission of the vehicle is increased by this retrofit. The regulations of the StVZO must be observed. It is therefore recommended to ask for a specific registration option at the responsible TU¨ V/DEKRA office before retrofitting. Outside Germany, please observe the laws on vehicle licensing applicable in your country.

How to connect a cable to another

How to connect a cable to another

here) and

strip the insulation at one point with a suitable tool (cable stripper/cutter knife).

|
2| Now take the cable of the cable set, which you want to connect, (yellow marked

here) and strip the insulation at the end.

|
3| Twirl the wires of the stripped cable together.|
4| Place the end of the cable you want to connect under the stripped point of the cable

of the vehicle…

|
5| … and wrap the cable you want to connect around the cable of the vehicle.|
6| Lastly, stick insulating tape around the connection point.|

Note Cable Inscription/Color

If our cable set consists exclusively of grey wires, connect the wires according to the cable inscription.

Assembly Instructions

The following illustration shows the cable routing as well as the position of the individual components.

• 1 External sound generator incl. bracket
• 2 Control unit for engine sound generation
• 3 Sound Booster Pro (module)
• 4 Pushbutton

Removing trim panel driver’s side front

Removing trim panel driver’s side front – instructions

take it

out afterwards.

| 2xT20
2| Remove the lateral covering of the dashboard using a trim tool.|
3| Now loosen the three marked screws at the bottom of the front trim panel of the

dashboard.

| 3xT20
4| Remove the light switch by pushing it inwards, turning it to parking light and pulling

it out. Afterwards loosen the marked plug and take the light switch out completely.

|

Removing trim panel driver’s side front – instructions

trim panel

of the dashboard out afterwards.

| 2xT20
2| Loosen the marked covering of the sill trim with a trim tool.|
3| Remove the marked plug and take the covering out completely afterwards.|
4| Remove the sill trim using a trim tool.|

Connection CAN-High & CAN-Low / ground / ignition lead

Connection CAN-High & CAN-Low / ground / ignition lead – instructions

steering

column (see notes page 6) as follows:

|
 | – CAN High (black/white) to orange/black|
 | – CAN Low (black/yellow) to orange/brown|
2| Connect the ground cable (brown) to the marked ground spot behind the carpet at

the bottom of the a-pillar of the driver’s side.

| 10er

socket

3| Now connect the cable for ignition lead (red/white) also to the plug of the light

switch to PIN 1 (colour of the cable at the plug = yellow/black).

|
4| Place the control unit as well as the module in the dashboard and attach both with

cable ties.

|

Routing connecting cable sound generator

Routing connecting cable sound generator – instructions

the sill

trim.

|
2| Route the cable further from the sill trim beneath the driver’s seat with a pull

through aid. Move the seat to the very front for this.

|
3| Guide the connecting cable through the marked grommet under the seat to the

underbody.

|

Installation sound generator

Installation sound generator – instructions

13er

socket

4| Attach the sound generator with the just loosened screw.| 13er

socket

5| Connect the connecting cable to the sound generator and attach the delivered steel

wire rope to the sound generator as well as to the bracket of the middle silencer.

|
6| During our test installation, no pushbutton was installed. Choose a suitable po-

sition for the pushbutton, for example at the lower trim panel of the dashboard of the driver’s side or the center console, drill an appropriate hole and install the pushbutton afterwards.

| 7mm

drill

Software

Notes for the software

https://www.

sound-booster.com.

|
 | Step 2: Turn the ignition of the vehicle on and only then connect the PC / Mac

with a USB cable with our module. It is important here to make sure previously that plus and minus are connected correctly. If this is not the case, a damage at the computer or at the control unit can result.

|
 | Step 3: Start the downloaded software and first click on search and afterwards on

connect.

|
1| You will be forwarded automatically to the diagnosis side, on which you can see the

following things at a glance:

|
 | Software: Software version / creation date|
 | Active profile: The actually activated profile is indicated here.|
 | Vehicle: The automatically identified vehicle is indicated here.|
 | System Status: You can see here if the connections are correct.|

Notes for the software

Manual

Selection as follows:

|
2| Open the dropdown-menu, search for your vehicle and select it.|
3| Click on Manual Selection to save the vehicle on the module permanently.|
 | If you don’t find your vehicle in this list, it is possibly necessary that the software has

to be adapted to your vehicle. For this, please contact us via e-mail: info@kufatec.de or by phone: +49 (0) 4551 / 80 810 888. We will make an appointment with you, at which we will adapt the software to your vehicle per Team Viewer (telemaintenance).

|

Important Information Sound Booster

Please use for the fixation of the Sound Booster suitable high tensile screws. In order to avoid losening of the screws by vibration please make the screws safe with appropriate factory material e.g Threadlock. Please additionally check the stability of the Sound Booster regularly and if necessary retighten the screws. In case of no consideration we do not assume liability for possible damages. After successful installation we recommend to cover the sound generator with a zinc spray. Make surethat you cover the opening of the sound generator so that no zinc spray can’t get inside the sound generator. As additional safety the delivered steel cable and the retaining clips have to be tightened on the Sound Booster as well as at a suitable position in the car. This safety cable is an additional security should the tightening screws should be released by vibration.

Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de

References

• Contact form | Support, phone | KUFATEC Deutschland

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>