Electrolux EHG8351SCP Gas Hob User Manual
- June 3, 2024
- Electrolux
Table of Contents
Electrolux EHG8351SCP Gas Hob
Safety instructions
- Do not use gas other than that which is specified on the label attached.
- Do not place anything, e.g. flame tamer, asbestos mat, between pan and pan support as serious damage to the appliance may result. (Fig 1)
- WARNING:· In the event of the burner flames being accidentally extinguished, turn off the burner control knob and do not attempt to re-ignite the burner for at least 1 minute.
- Do not remove the pan support and enclose the burner with a · For burner fitted with a flame supervision device, if after wok stand not supplied by Electrolux as this will concentrate the 15 seconds of ignition operation the burner has not lit, flame and deflect the heat onto the top plate. (Fig 2) stop operating the device and open the compartment door and wait at least 1 minute before attempting a
- Do not use large pots or heavy weights which can bend the pan further ignition of the burner. support or deflect the flame onto the top plate. (Fig 3)
- If nozzle holes are blocked, use a thin wire or pin to Locate pan centrally over burner so that it is stable and does not pierce and clean the nozzle holes. overheat the appliance. (Fig 4)
- Use only wok support supplied or recommended by the manufacturer of the appliance. (Fig 5)
- Wok support to be used for wok and other trivets for flat bottom pot.
- The unit to be used for cooking only. Do not dry towels, clothes, · etc., over it. If this is done, there is danger of fire.
- If a gas leak is found, close stopcock, open up all windows and call your dealer. Do refrain from turning an electric switch on or off, lighting a match, smoking or using a lighter.
- Use the appliance in a well-ventilated room.
- Do not use vinyl gas hose. It is liable to be softened by heat. Use only a rubber hose.
- Be sure to turn off the ignition knob and regulator of the cylinder after use.
- Avoid touching the burner, pan stand etc., immediately after use. Otherwise you will get burnt.
- Ensure that the rubber hose does not touch any part of the unit or lies underneath it.
- Connect the rubber hose to the gas inlet and fasten it with a hose clamp.
- The pan stand leg nearest to the flame will have discoloration after use. Such phenomenon is normal.
Parts identification
FlameShield Trivet
The FlameShield Trivet reduces heat -loss to deliver more intense heat to the
cooking process, for effortlessly perfecting dishes from soups to sauces to
stir-fries. the curved trivet profile works like cradling a candle, cupping
the flame and channeling the energy directly onto the bottom of the pan. By
directly heat more efficiently, our FlameShield Trivet cook tops cook faster
and consumer less energy than previous models, helping you to achieve quick,
tasty meals, whilst also lowering your energy bills over time.
The Class of the appliance: Class 3
These instructions are only valid if the country symbol appears on the
appliance. If the symbol does not appear on the appliance, it is necessary to
refer to the technical instructions which will provide the necessary
instructions concerning modification of the appliance to the conditions of use
of the country. Prior to installation, ensure that the local distribution
conditions (nature of the gas and gas pressure) and the adjustment of the
appliance are compatible The adjustment conditions for this appliance are
stated on the label (or data plate). This appliance is not connected to a
combustion products evacuation device. It shall be installed and connected in
accordance with current installation regulations. Particular attention shall
be given to the relevant requirements regarding ventilation. Avoid using of
cooking vessels on the hotplate that overlap its edges. The use of
inappropriate hob guards can cause accidents. Hob guards cannot be used. The
use of a gas cooking appliance results in the production of heat, moisture and
products of combustion in the room in which it is installed. Ensure that the
kitchen is well ventilated, especially when the appliance is in use: keep
natural ventilation holes open or install a mechanical ventilation device
(mechanical extractor hood). Prolonged intensive use of the appliance may call
for additional ventilation for example opening of a window or more effective
ventilation for example increasing the level of mechanical ventilation where
present.
CAUTION:
” In case of hotplate glass breakage: shut immediately off all burners and
any electrical heating element and isolate the appliance from the power
supply. do not touch the appliance surface, _ do not use the appliance.”
Installation instructions
-
Have the installer show you the location of the gas shut off valve and how to shut it off in emergency.
Be certain all packing materials are removed from the hob before operating to prevent fire or smoke damage that could be caused by the presence of these materials. -
Observe all instructions for minimum clearance to any combustible surfaces. These should be in accordance with information on the rating plate and with national fire laws.
-
If the hob is installed near windows, proper precautions should be taken to prevent curtains from blowing over burners creating FIRE HAZARD.
-
When choosing a location for this hob consider, availability and position of gas and electric supply paths.
-
Any openings around gas and electric service outlets shall be closed at the time of installation.
-
Do not install another hob next to this unit.
-
If clearance between side/back walls and periphery of the burner is less than 200mm, the walls must be protected with a non-combustible material. The protection must
-
extend a minimum distance of 450mm above the burner. Horizontal surfaces less than 750mm vertically above the cooktop must also be protected.
-
The underside of the hob must be checked to ensure that there are no projections which might foul the hob. Make sure that the countertop is solidly supported and can withstand the weight of the hob.
-
Check that the cabinet is leveled from side to side and from front to back in its installed position.
-
Cabinet ventilation can be improved by the provision of air holes to the cabinet. Care should be taken to ensure that ventilation holes are not obstructed.
-
When fitting a vent hood above the hob, refer to the manufacturer own installations relating to that product. However as a general rule, a minimum clear vertical distance of 750mm (30″ should be maintained between the cooktop and the underside of any cupboard, wall unit or vent. (Fig 6)
-
Any cabinet installed above the cooktop must not be greater than 325mm (13″ deep. (Fig 6)
-
The edge of the hob must have a minimum distance from the real wall of 55mm. (Fig 6)
BATTERY COMPARTMENT
- When the battery is exhausted; or the spark become weakness, a new battery should be replaced.
- The battery compartment is located as shown in the diagram. Please place the battery in correct polarity as shown.
Warning: Please take out the battery if not use for a long time.
Installation procedure
- Before installing the appliance, check that the location provides the required clearances from combustible materials and check if necessary to provide protection to adjacent surfaces as required by the regulation. Make provision for the gas supply to be connected to the location.
- Cut the opening in the bench top by the cardboard – template given in the hob packing or to the dimensions shown in Fig 7.
- Remove the hob from the carton. c Install the hob in the cut-out (Fig 7)
- Connect gas supply to inlet of hob. Turn the gas on and check for leaks using soap solution and brush around all the joints and connection.
- Test the appliance; depress the control knob and turn to full flame setting to activate the electric igniter. The burner will ignite. Adjust control knob to the desired setting. On initial usage you may have to repeat this ignition function several times (to allow air to be purged from the gas supply system). No adjustment should be necessary. If any problem occur, refer to the servicing instructions or the fault finding chart.
- Ensure the manual is left with the user. If any of the above procedures do not produce satisfactory results, the agent service department should be consulted for more specialized assistance.
- This gas hob has been tested for operating on town gas pressure up to 31 mbar
Gas connection
- The supply hose must be visible for its entire length (max. one meter) and must be secured with a hose clamp X (Fig 8). The sealing washer must be fitted.
Flexi Installation Cut Out
c The smaller burner (lower) box of this cooktop combined with the extended glass overhang, and flexible bracket makes installation into existing counter cut-outs easy without additional modification. cFor replacement purchase, ensure cutout size fall within the given dimension for the desired hob. cGas hobs should be secured properly with the flexible brackets provided to prevent it from moving in Fig 7.
Model Cut-out Dimension
- EHG8260SC Width (700-790)*Depth(405-475) R50
- EHG8351SCP Width (700-790)*Depth(405-475) R50
Bench cut-out size viewed from front of bench, i.e. control panel at front. If clearance between side/back walls and periphery of the burner is less than 200mm, the walls must be protected with non-combustible material. The protection must extend a minimum distance of 450mm above the burner. Horizontal surfaces less than 750mm vertically above the hob must also be protected.
IMPORTANT SAFETY INSTRUCTION :
Upon completion of gas installation connections, it is cteosmt)p ulsory to
check for gas leakage at the joint. (Soap Soap test procedure cTurn the burner
controls off and turn on the gas supply. cApply soapy solution to each joint.
(Figure 8) cFormation of bubbles indicates leakage and must be tightened.
cRepeat soap test
Ignition burners
-
Check to make sure that the gas supply is accessible and set up with the necessary and appropriate fittings/connectors.
-
Turn all control knobs to off position.
To turn off the gas, rotate the knob anticlockwise until you feel the distinct click on the knob and the indicator on the knob is pointing to “0”. -
It is also advisable to cover any boiling casserole and as soon as the liquid starts to boil, lower the flame enough to keep the boiling point
-
To ignite, hold the knob and depress for several seconds, rotate anti-clockwise to maximum gas flow position. For models with thermocouple, keep the knob depressed about 5~8 seconds, otherwise the flame will extinguish.
-
If the burner does not light the first time, repeat Step 4.
-
If the flame extinguishes suddenly, repeat Step 4.
-
When using the unit again immediately after having once turned it off, wait for about ten seconds before re-igniting.
-
Each burner has its own independent ignitor.
-
When the burner is lit, turn the knob to adjust the flame size according to your needs. This needs no depression of the knob.
For burner fitted with a flame supervision device, if after 15 seconds of ignition operation the burner has not lit, stop operating the device and wait at least 1 minute before attempting a further ignition of the burner.
Using the hob correctly
- To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that the flame will not spread beyond the bottom of the vessel (Table 1).
- It is also advisable, as soon as the liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering
Choice of burner
- A semi-rapid burner is for special low heat, simmering and slow cooking.
- A wok burner is for very fast heating using a wok or large pan.
NOTE : Remember that a wide-bottomed pan allows a faster cooking than a narrow one.
- Always use pots which properly fit what you have to cook.
- Particularly make sure that the pans are not too small for liquids, since these could easily overflow.
- The pans should not be too large for a faster cooking.
- You should use pans with the right diameter to fit the burner, in order to make the most out of it, thus reducing gas consumption as in Fig 12.·
Burner caps & crowns
- These can all be lifted off and removed for separate cleaning.
- Ensure burner caps and crowns are thoroughly dried after cleaning or spillage.
- When cleaning the burner, ensure that all the flame ports, injector hole and other holes are free of any blockage. (Fig 13,14) maintenance and care 9
- After cleaning, ensure the burner caps are reassembled properly into position.
- After cleaning service, when assembling the burner crown and caps, care must be taken to ensure the spark plug is not knocked. The spark plug will crack if knocked and may face risk with flame ignition problem.
What to do if
Phenomenon Reason Solution
Burner will not light… Air in gas line Purge gas line
Blockage in line Trace back & clear
Ignition not sparking Check lead & electrode
Battery is flat Replace battery
**** Burner not fitted correctly Fit burner in correct position
Burner lights back to injector… Excessive lint up of burner mixingtube Remove & clean burner
Excessive gas pressure
**** Check gas regulator pressure &
adjust if necessary
Burner has explosive ignition… Excessive gas pressure Check gas regulator pressure &
adjust if necessary
lgnitor not sparking… Excessive electrode gap Check gap, and adjust so it is
**** 4-5mm
lgnitor connections loose Check connections to ignitor, replace if faulty
Battery is flat Change a new battery
WARNING : Do not spray aerosols in the vicinity of this hob while in operation. Some propellant gases can break down when heated and produce corrosive vapours which will attack some materials. Articles which are made from flammable materials should not be stored in drawers or cupboards immediately below this hob. Do not store articles within 50mm of the base. Do not touch spark ignitor while lighting the burner. Where this appliance is installed in a marine craft or in caravans, it shall not be used as a space heater.
Technical specifications
StepFlame
StepFlame delivers precise control on three rings of flame with stepped
settings that click into place as you change the heat intensity. The pre-
defined settings guarantee the same flame and heat level every single time,
giving you both control and flexibility. This is perfect for a variety of
techniques and dishes from delicately melting chocolate, to gently simmering
sauces or stir-frying rice at high temperatures.
Standard warranty conditions
We, Electrolux, undertake that with warranty period (refer to each country location for warranty period months) this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labor materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorized by us. All service work under this guarantee must be undertaken by an Electrolux Service Center. Any appliance or defective part replaced shall become the Company property. This warranty is in addition to your statutory and other legal rights. This warranty does not include maintenance, like cleaning of hob. It is encouraged to change regulator every 5years and the hose every 2years. The manufacturer waives all liability for failure to observe the instructions for the appropriate installation, maintenance and use of the appliance.
If you need any technical help or would like more information about our products, please do not hesitate to contact our Customer Care Center, listed below:
Indonesia
Hotline service: 08041119999 PT. Electrolux Indonesia Electrolux Building
Jl.Abdul Muis No.34, Petojo Selatan, Gambir Jakarta Pusat 10160 Email
:customercare@electrolux.co.id SMS &
WA : 0812.8088.8863
Malaysia
Consumer Care Center Tel: 1300-88-11-22 Electrolux Home Appliances Sdn. Bhd.
Corporate Office Address: Unit T2-7, 7th Floor, Tower 2 , Jaya33 Hyperoffice,
No. 3, Jalan Semangat, Seksyen 13, 46100 Petaling Jaya, Selangor Office
Tel : (+60 3) 7843 5999 Office Fax : (+60 3) 7955 5511 Consumer Care
Center Address: Lot C6, No. 28, Jalan 15/22, Taman Perindustrain Tiong Nam,
40200 Shah Alam, Selangor Consumer Care Center Fax : (+60 3) 5524 2521
Email :
malaysia.customercare@electrolux.com
Philippines
Consumer Care Center Toll Free : 1-800-10-845-CARE 2273 Consumer Care
Hotline : (+63 2) 845 CARE 2273 Electrolux Philippines, Inc. 10th Floor.
W5th Avenue Building 5th Avenue Corner 32nd Street Bonifacio Global City,
Taguig Philippines 1634 Trunkline: +63 2 737- 4756 Website :
www.electrolux.com.ph Email :
wecare@electrolux.com
Singapore
Consumer Care Center Tel: (+65) 6727 3699 Electrolux S.E.A. Pte Ltd. 351
Braddell Road, #01-04 Singapore 579713 Office Fax : (+65) 6727 3611
Email : customer-care.sin@electrolux.com
Thailand
Consumer Care Tel : (+66 2) 725 9000 Electrolux Thailand Co., Ltd. Electrolux
Building 14th Floor 1910 New Phetchaburi Road, Bangkapi, Huai Khwang, Bangkok
10310 Office Tel : (+66 2) 7259100 Office Fax : (+66 2) 7259299
Email :
customercarethai@electrolux.com
Vietnam
Consumer Care Center Toll Free : 1800-58-88-99 Tel : (+84 8) 3910 5465
Electrolux Vietnam Ltd. Floor 9th, A&B Tower 76 Le Lai street – Ben Thanh Ward
– District 1 Ho Chi Minh City Vietnam Office Tel : (+84 8) 3910 5465
Office Fax : (+84 8) 3910 5470 Email :
vncare@electrolux.com
305536623 Rev.A
References
- OLux.cOm is For Sale | BrandBucket
- Electrolux Philippines | All Home Electrical appliances & Kitchen appliances
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>