SNAP ATTACK Football Machine Instruction Manual

SNAP ATTACK™ FOOTBALL MACHINE
PATENTS APPLIED FOR
INSTRUCTION MANUAL
OPERATION · SETUP · USE & CARE · SERVICE

INTRODUCTION

Thank you for purchasing this Sports Attack, LLC . equipment.
Your Snap Attack™ will be shipped in the right-hand spiral position.
Proper assembly, careful operation and consistent maintenance of this equipment will ensure that it gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly set up the Snap Attack Football Machine, and to use, care for and maintain the Snap Attack in a manner which will ensure its optimum performance.

WARRANTY STATEMENT

What is most important to Sports Attack is that your machine meets your expectations of quality and performance . We stand behind the material and workmanship of our machines for five (5) years from the date or original purchase for institutional and residential use and one (1) year for commercial environments, with the following  exceptions:

• Throwing Wheels are warranted for two (2) years;
• Electronic Controller is warranted for two (2) years; and,
• Throwing Wheel Motors are warranted for two (2) years.

This warranty excludes any cosmetic issues or normal wear and tear of the unit, and is not in effect if the machine has been misused, misapplied, improperly assembled, or modified without the express written permission of Sports Attack. In addition, this warranty does not apply to damage in transit, in any accident unrelated to the direct operation of the equipment, or by fire, flood or act of God.
If you encounter any issues during the warranty period, Sports Attack will quickly get your machine back in working order . If the warranty repair involves a replacement part, we will make sure you get both the part and easy instructions for replacement at no cost to you . If a service person is needed, Sports Attack will pay the pre-approved labor charge to get your machine back in working order.
Please know that any problem can quickly be resolved with a phone call to our experienced, responsive customer service department at 800 .717 .4251 . We are here to answer your questions and to make sure your machine provides you years of service.
RETURNS
Sports Attack manufactures the highest quality sports training equipment in the world. If for any reason you are not satisfied, a machine can be returned within 30 days of  receipt for any reason for a full refund less a 10% restocking fee . Cost of shipping the unit back to Sports Attack will also be the responsibility of the purchaser . Please note that the refund amount may be reduced by any non-cosmetic damage to the machine. If you have any questions or concerns, please give our experienced, responsive customer service department a call at 800.717.4251.

SHIPPING DAMAGE CLAIMS PROCEDURE

NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory.  Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery .
IF SHIPMENT ARRIVES DAMAGED

1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt, and that the note of loss or damage is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the damage .
3. CONCEALED LOSS OR DAMAGE: If damage is unnoticed until the merchandise is unpacked, notify the transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them. This must be done within fifteen (15) days from the date the delivery was made to you . Be sure to retain the container for inspection.

Sports Attack, LLC. cannot assume liability for damage or loss incurred in transit . We will, however, at your request, supply you with the necessary documents to support your claim.
Warranty/Shipping
To register the Warranty, please go to our website: www.sportsattack.com/warranty
For repairs and service after the Warranty period, please call:
Customer Service Dept.
Ph 800.717.4251
Fx 775 .345 .2883
RETURNS
To return an item, please contact our Customer Service Department at 800.717.4251.
A 15% restocking fee will be charged for any items accepted for return . It is the customer’s responsibility to handle the repacking and shipment (as well as all associated fees) back to Sports Attack .
No returns will be accepted after 30 days of receiving this product.

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY
Use a 115 volt single phase 3-wire grounded power source . Up to 200 ft . from power source, use a minimum #14/3 grounded 3-wire extension cord . Over 200 ft . from  power source, consult a licensed electrician for required power cord size.
OPERATING SAFETY
CAUTION: Never reach down near moving throwing wheels for any reason! If it is necessary to reach into the throwing wheels, ALWAYS:

1. Turn speed dial to “0” .
2. Turn the power switch “OFF” .
3. Unplug Snap Attack™ from power source .
4. Wait until the throwing wheels have come to a complete stop before reaching hands or fingers anywhere near the throwing wheels.

CAUTION: Carefully check Snap Attack for completeness and condition before connecting to electrical power:
Carefully check the throwing wheels frequently for cleanliness, chips and cracks . Do not use the machine if the throwing wheels are damaged, or if chips or cracks appear in the wheels. (For damage within warranty period, see Warranty Statement, page 1.)
ALWAYS set the speed control to “0” before connecting the machine to power.
Check that the speed control is at “0” before turning the throwing wheels “ON”.
Do not allow anyone to walk in front of the Snap Attack Football Machine if it is connected to electrical power .
CAUTION: DO NOT plug in or energize this equipment until all assembly instructions and operation instructions are read and followed.
BALL SELECTION
Balls must be official size and consistent in type to produce repeatability.
Never use wet or damp balls! Ball air pressure must be between 10-12 lbs .
Air Pressure & Distance

Slippage occurs at higher wheel speeds with lower air pressure.
We recommend higher air pressure to prevent slippage.
WARNING
PERSONAL INJURY HAZARD
Carefully read all instructions in this manual, and all labels and warnings on Snap Attack before using this machine .
Use machine only under adult supervision . Failure to operate Snap Attack as described in this manual can result in severe personal injury or death .
ELECTRICAL SHOCK HAZARD
The Snap Attack must be connected to a properly grounded electrical receptacle .
Do not operate on wet ground .
CAUTION
PERSONAL INJURY HAZARD
Keep hands away from throwing wheels anytime the machine is connected to a power source .
Carefully check the Snap Attack for completeness and condition before connecting to electrical power .
EQUIPMENT
ELECTRICAL DAMAGE
Keep hands away from throwing wheels anytime the machine is connected to a power source .
Carefully check the Snap Attack for completeness and condition before connecting to electrical power .
BALL REQUIREMENT
Do NOT use synthetic leather footballs . We recommend full grain leather .

COMPONENT VIEW

|
---|---

ADDITIONAL INFORMATION
If you have any questions regarding the safe operation of the Snap Attack, please call:
Sports Attack Customer Service Department
Ph 800 .717 .4251
Fx 775 .345 .2883
GENERATOR INFORMATION

1. Snap Attack requires a generator capable of providing clean electricity (invertor technology) of a minimum 1000 watts at 120 volts 60hz .

2. Be sure the power switch is “OFF” before plugging Snap Attack into the generator .

3. Start the generator and allow it to reach full speed before turning the power switch “ON”
   IMPORTANT: Generator speed fluctuations can damage the electronic speed control . Maintain adequate fuel in the generator at all times.

4. Turn the Snap Attack power switch “OFF” before shutting off the generator and before unplugging the Snap Attack.

SET-UP & PREPARATION

Using the Snap Attack on the ground as a centering machine
The Snap Attack can be used in one of two modes. The first is when it is used on the ground to perform as a centering machine . The second is when it is used on its stand to perform as a quarterback when throwing passes or as a kicker or punter.
Setting machine up to perform as a centering machine

1. If machine is attached to stand:
   a. Tip machine up and over onto feet (See Figure 1).
   b. Unsocket the three legs and remove both knobs (See Figure 2) and store on same bolts .
   c. Remove machine from stand .

2. Open rear leg support latch and insert rear leg support (See Figure 3).

3. Close latch over rear leg and tighten with wing nut (See Figure 4).

4. Tip machine back onto rear leg .

5. Point machine to desired direction .

6. Adjust angle by using your left hand to grab the passing handle and right hand to depress and adjust into 1 of 10 positions .

7. Turn machine on and turn Wheel speed control Knob to approximate speed .

8. Set ball carefully into Ball Cradle and feed ball into throwing wheels.
   IMPORTANT: For tightest spiral slide Ball Cradle gently, allowing wheels to capture & impel ball . Do not jam cradle and ball into machine .

9. Adjust elevation and wheel speed until exact spin is attained .

Setting- up As A Centering Machine
SAFETY HINT
When lowering or lifting, Snap Attack keep your back straight and lift with your legs . Be ready to grab the wheel guard and guide Snap Attack into the upright position .
WARNING HAZARD FROM HIGH-SPEED PROJECTILES
Being struck by a thrown ball can cause serious injury or death . Make sure that no one steps in front of Snap Attack while it is connected to electric power.
Clear everyone away from machine before connecting Snap Attack to electric power.
Snap Attack in centering/snapping positionUsing the Snap Attack on the stand to throw passes, punts and kicksoffs
IMPORTANT: Lock pin A must be removed (See Figure 1) and stored in adjacent holeto left . This will allow machine to pivot horizontally.
IMPORTANT: For maximum distance, balls must be properly inflated. (See chart at bottom of page 2).
SETTING MACHINE UP

1. Using knobs (See Figures 3) which are stored on bolts, attach throwing head to undercarriage (See Figure 2), tighten wing nuts B securely to undercarriage.
2. Insert 3 legs into sockets. (See Figure 2)
3. Using lifting handles (See Figure 1) tilt machine up onto all three tripod legs.
4. Remove lock pin A and store in adjacent hole to left (See Figure 4).
5. Loosen horizontal control handle D (See Figure 2 & 4).
6. Loosen pass and kick elevation handle E (See Figure 2).
7. Plug machine into power source. (110v)
8. Turn power switch “ON” .
9. Loosen wheel tilt handle E (See Figure 2) . Over time this wheel tilt handle G will have to be adjusted adjust loosen bolt until handle angle be changed to new proper  position . Then tighten bolt securing handle in adjusted position .
10. Using wheel tilt angle handle G (See figure 2) push forward for end-over-end or pull back for passes and punts .
11. Dial wheel speed F to approximate speed .
12. Continue throwing test balls and adjusting speeds until desired distance and speed is achieved .
    NOTE: Maximum post height should not exceed 34” with the stand on the ground. See page 11.

SHUTTING DOWN & TRANSPORTING

TURNING SNAP ATTACK “OFF”

1. Turn the power switch “OFF” and unplug Snap Attack from the power source .

TRANSPORTING WITH STAND

1. Be sure machine is turned “OFF” and wheels are not turning .

2. Unplug cord from extension cord, standard outlet or generator .

3. Frame lock pin A (See Figures 2 & 4) must be inserted in hole to right, locking head into position for transporting .

4. Using the elevation control, tilt the throwing heads up (to high position) and lock into place (See Figure 5). This will facilitate transporting.
   Setting-up for Pass, Punt and Kickoffs
   SAFETY HINT
   When lowering or lifting, Snap Attack keep your back straight and lift with your legs . Be ready to grab the wheel guard and guide Snap Attack into the upright position.
   WARNING HAZARD FROM HIGH-SPEED PROJECTILES
   Being struck by a thrown ball can cause serious injury or death . Make sure that no one steps in front of Snap Attack while it is connected to electric power.
   Clear everyone away from machine before connecting Snap Attack to electric power .
   

5. Using handles C (See Figure 1) tip machine up and over onto lifting handle assembly feet See Figure 1). Unsocket two lower (front) legs, leaving upper (rear) leg in socketed position.

6. Lift rear leg and roll machine (See Figure 5).

PASSING, PUNTING & KICKOFF
The Snap Attack is able to simulate both right-hand and left-hand spins. Two wheel tilt handles G (See Figure 1) are located underneath both motors, one on each side, and are used to change the angle of the wheels to provide either end-overend or spiral ball delivery .
L- Left spiral pass, left handle is all the way forward away from operator, right handle is in the opposite position .
R- Right spiral pass, right handle is all the way forward away from operator, left handle is in the opposite position .
K- Lines indicate range for kick-off setting, depending on ball size and inflation, forward line provides furthest distance . Both handles must be in the same position in the slider for an end-over-end kick .
FEEDING BALL INTO THROWING WHEEL (See Figure 6)
IMPORTANT: Be sure cradle is pulled all the way back. Use ball feed handle J (See Figure 2). Ball is positioned the same in cradle for any pass, punt or snap. See Figure 6).
CARE, CLEANING & MAINTENANCE LUBRICATION
(once per season, or as required)

1. Pass & Kick Elevation Control Handle E (See Figure 2) Apply fresh grease to threads .
2. Horizontal Swivel Lock
   a .Completely remove the horizontal pivot control handle . Clean all old grease, dirt, etc . from the threads .
   b . Wipe the threads with a very small amount of fresh grease .
   c . Reinstall .

THROWING WHEEL MOTORS
Motors are sealed and require no lubrication . Check bolts for tightness once a season.
Tighten bolts securely, but do not over-tighten. (See page 7).
CLEANING THE THROWING WHEELS
The throwing wheels must be kept clean to maintain accuracy . Clean the wheels periodically to control the build-up of grass and dirt.

1. Turn the power switch “OFF” and allow the wheels to come to a complete stop.
   Unplug Snap Attack from electric power.

2. Dampen a rag with soap and water . Turn the throwing wheel by hand and scrub the wheel until the build-up is removed . For very heavy build-up, a synthetic scouring pad, such as a Scotch-Brite® scouring pad, may be used sparingly .

EXAMINE THE MACHINE
Examine Snap Attack for condition and completeness before every use:

1. Throwing wheels must be tight on the motor shafts . Check that the four bolts holding the motor to the throwing head assembly are tight .
2. Wheel guard and ball cradle must be securely fastened .

Shutting Down & Transporting | Maintenance

Figure 5 Lift rear leg and roll. Shown being used with pass and punting stand.
CAUTION
PERSONAL INJURY HAZARD
Never attempt to clean the throwing wheels while they are turning . Rags or implements caught in spinning wheels can cause serious injury . Unplug the machine before cleaning the wheels or performing any service .

COMPONENT REPLACEMENT

THROWING WHEEL REPLACEMENT

1. Turn the throwing wheels “OFF” and unplug the power cord . Remove 4 bolts holding the top wheel guard to the bottom wheel guard.

2. Hold the wheel so that it cannot move . Turn the keyway retaining bolt counter-clockwise using a box end wrench (See Figure 7).
   SUGGESTION: If the bolt is too tight, give the opposite end of the wrench a series of light taps with a hammer making sure the wrench remains on the bolt.

3. Remove the bolt and washers.

4. Work the wheel off of the motor shaft . Be sure to catch the key as it is freed from the keyway.

5. Ball throwing wheels are machine balanced . Small holes in the side of the wheel are applied at the factory and are normal.

Reassemble in reverse order.
a . Install wheel to motor shaft with key slots aligned .
b. Be sure the key is in place, and inserted so that it is flush with the boss at the wheel center.
c . Be sure the Washer and Lock Washer are installed in the right order, and that the keyway retaining bolt is tightened.
d . Test the wheel by spinning it by hand and making sure that it spins freely without wobble before turning the unit “ON” .
e . Be sure the top wheel guard is properly and securely reinstalled.
MOTOR REPLACEMENT

1. Turn the power switch “OFF” and unplug the power cord .
2. Remove top wheel guard (See Page 9).
3. Remove the throwing wheel .
4. Remove bottom wheel guard .
5. Remove four screws holding the controller into the control box . Note the position of the motor wires on the controller, then disconnect the wire for the motor to be replaced.
6. Note the routing of the motor wires . Loosen wire clamps and pull wire away from machine.
7. To remove motor, remove the 2 – 1 /4 ” x 3 /4 ” coarse Allen flat socket cap screws using a 5 /32 ” Allen wrench . Then remove the 2 – 5 /16 ” x 1” coarse thread bolts using a 1 /2 ” socket .
8. Reassemble in reverse order .

NOTE: Check bolts for tightness once a season. Tighten bolts securely, but be sure not to over-tighten.
Component Replacement | Optional Clamp
Figure 6
IMPORTANT NEW FEATURE-Same ball position in cradle is used for spiral pass, punt, kickoff and snap.
IMPORTANT!
Spiral Pass/Punt/Snap Position the locating point where seams intersect.
Figure 7 Hold wheel in place while loosening bolts.
CONTROLLER REPLACEMENT

1. Turn the power switch “OFF” and unplug the power cord .

2. Remove knob from the controller .

3. Remove four screws holding controller faceplate into main casting.
   Note the position of the main power and motor wires on the controller, then disconnect the wires. (See Figure 8) for the two motor wires and the main power cord wires. Loosen the nuts holding the speed control shaft (potentiometer) to the faceplate,

4. then remove the controller .

Reassemble in reverse order.
Be sure wires are correctly reinstalled . Motor wire connectors are different sizes . Be sure they are installed on the correct size terminal. Component Replacement
POWER CORD WIRE
Black (#1) On/Off switch
White (#2)
N on green control board
Green (#3)
Grounds to machine
CONNECTING WIRES

Left is the side with the Control Plate as you stand behind machine. Black motor wires are 3 /16 ” female disconnect and white wires are 1 /4 ” female disconnect.
EXPLODED VIEW – SNAP ATTACK™

1 Cane Tip
2 Leg
3 Swivel Assy
4 Handle Horizontal Swivel Lock
5 Locking Pin Frame to Swivel
6 Undercarriage Assy
7 Handle, Elevation
7a Bolt, Carriage
7b 5/8 ” Nylon Nut
8 Disc, Elevation| 8a bElevation Clutch
9 Throwing Head Assy
9a Snapping Tube Elevation Mount
10 Motor 110V
11 Motor 220V
12 Motor Mount Plate with Pin
13 Smile Plate
14 Throwing Wheel
15 Wheel Guard, Lower Left| 16 Wheel Guard, Upper Left
17 Wheel Guard, Lower Right
18 Wheel Guard, Upper Right
19 Controller (110V/220V)
21 Slide, Lower Cradle Slide
22 Slide, Upper Cradle Slide
23 Ball Cradle
27 Throwing Head to Yoke Knob
39 Knobb, Motor Lock
40 Travel Wheel
37 Universal Cart Clamp
---|---|---

PARTS LIST

Cart Clamp Kit (optional)
37| 130-3004| Universal Cart Clamp| 1

To order additional parts please contact:  Sports Attack Customer Service Dept.
Ph 800 .717 .4251
Fx 775 .345 .2883

ATTACHING OPTIONAL CART CLAMP

Designed to fit 2½” to 4” round or square post

1. Insert clamp bolt through top plate . Loosely attach washer and nut . Finger tighten .
2. Put 3 bolts through sides of clamps . Slide unit over post, then attach fourth bolt .
3. Center top plate to post . Begin tightening 4 clamps to top plate, but do not completely tighten .
4. Begin to secure the 4 side bolts . Completely tighten .
5. Completely tighten 4 clamp nuts to top plate .

CART CLAMP KIT

Tools needed are either a ¾ wrench or socket wrench.
Note: Maximum post height should not exceed 34” with the stand on the ground . When attaching the option cart clamp, slide unit over post and dry fit to ensure that maximum post height from ground to top of the post does not exceed 34” . If your post height exceeds 34”, you should cut your post so that it complies with this measurement.
Clamp can be used on round or square posts.

|
---|---
Figure 9 Insert clamp bolt through top plate.| Figure 10 Put 3 bolts through sides of clamps.

Figure 11 Slide unit over post and attach 4th bolt.

SNAP ATTACK™ FOOTBALL MACHINE
Sports Attack, LLC.
800.717.4251
www.sportsattack.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>