Chikili BBH-0007 Electric Ride On Car User Manual

June 3, 2024
Chikili

BBH-0007 Electric Ride On Car
User ManualChikili BBH-0007 Electric Ride On Car

BBH-0007 Electric Ride On Car

ELECTRIC RIDE ON CAR
Installation and Operation Instruction
All pictures shown are for reference purpose only. Actual product may vary due to the production.
Please read this specification carefully before installation in order to avoid operating errors or damages. Make sure that the kid will be safe. The user should safekeeping the specification.

Specification

Car type BBH-0007
Storage battery 12V4.5AH*1
Electric motor 12V 3902 (drive) 12V3801 (turn)
Suit age 3 years+
Max weight 30Kg
Size 1128X671X524mm
Speed 3.0-5.0km/h
Utility 8-12hours (charge), 60-80minutes (use)
Charger AC100-240V 50-60Hz(input), DC12V(output)
Battery of remote control Two pieces of AAA 1.5V

Warning

  • Small parts. Not suitable for children under 36 months
  • Products should be adult assemblyBefore the assembly screw split pin and other dangerous sharp tips!
  • Small parts in order to avoid damage and ingestion may cause a choking hazard, please send small parts away from children under 3 years old!
  • The children can not drive alone without adults,and caregivers in use process shall not be allowed to leave!
  • After charging the storage battery by the adults,before using this product, please recharge!
  • In order to avoid harming the children, please will pack materials such as plastic bags away from children!
  • Please check the product regularly to make sure that the electric wire, plugs, outer case and other parts are normal.
  • If something is damaged, please stop using the car until it is fixed!
  • Two AAA dry cells are for the remote controller!
  • Use all the cells or batteries in the right way!
  • If the line with no connection, do not insert the output socket!
  • The packaging and instructions must be retained since it contains important information!

Parts Names

Installation Steps

1.Install front wheel
Put one washer on the front wheel axle and install the front wheel, then put another washer on the front wheel. Fix it with M8 Nut. Clamp the wheel cover.cRefer to PIC1
2.Install rear wheel
The drive motor has been installed on the car body, install rear wheel and put one M10 washer then fix with one M8 nut, finally clamp the wheel core cover. (Refer to PIC 2). 3.Install the auxiliary wheel
Remove the screw from the rear of the body, and fix the auxiliary wheel with screw.cRefer to PIC 3
4.Install bumper
Place the bumper in front of car body.cRefer to PIC 4
5.Connect the power supply
Dock the docking plug before installing the seat. (Refer to PIC 5)
Note: Power plugs cannot be operated in reverse.
6.Install the seat
The back of the seat hook into the body of the card slot. Screw two pieces M4x30 screw seat. (Refer to PIC 6)
7.Install the steering wheel
Connect the plug and install the steering wheel on the steering shaft, then fixed with M5x35 bolt and M5 nut.cRefer to PIC7)
Note: Before installation, distinguish the front and rear positions of the steering wheel to avoid reverse installation.
8.Install the windshield
First connect the plug-in and install the windshield into the card slot of the car. (Refer to PIC 8)
9.Install the rear view mirror
Insert the mirror directly into the body.cRefer to PIC 9)
10.Use the Pull Handle &Remove the battery
Rotate the Pull handle out. (Refer to PIC10)
11.Dashboard indication
a. Power Switch —(1)Turn on power switch ,the light will be bright and there is an engine sound.
b. Dashboard equipped with music function and it can connected cellphone, adjust the volume, power display, etc.
c. Steering wheel —The steering wheel equipped with music and horn, Children can adjust by themselves.
d. Go forward/ Stop/ Back forward switch-When manual for driving it can control to go forward or backward when they step on the foot pedal. cRefer to PIC 11)

12.Charging indication
When the power display shows lower power, please charge the battery in time. Find the charging input socket below the seat. Plug the charger port into the input socket. Plug the charger plug into a wall outlet. The battery will begin charging.cRefer to PIC 12)
13.Remote controler operation

Step 1: Open the battery cover of the remote controler and load into 2pcs AAA (1.5V) batteries;
Step 2: Turn off the power switch on the car;
Step 3: Hold down Forward and Back buttons at the same time, the Speed display will flash. Wait for a moment, the Speed display red light stop flashing, control success.
Speed button:
A red light for low speed, two red lights for medium speed, three red lights for high speed. Brake button: press this button for stopping the car, red speed light will flashing. Press brake button once again, the car can work.
When the remote control is operated, the pedal switch of the product is invalid; when the remote control is cut off, the pedal switch can be used.
14.Fault and solutions

Type of fault Type of Analysis of causes Solutions
The car can’t move The battery is below normal level

Safety protection of line The screw on the wheels has fell off
The battery connector has fell off
The battery is damaged The electrical equipment is damaged
The motor is damaged| Charge the battery Wait for a moment Tight the screw again Change the battery Bring it to repair Contact the seller
The battery can’t be charged| Battery connector has fell off Battery charger is powered off Battery charger is damaged| Plug into again  Plug into again
Change the battery charger
Running distance per charge is short| Battery is not full Battery is old| Charge the battery again
Change the battery
There is noise
and heat when charge the battery| Chemical reaction| It is normal
The speed is low| Battery is old
Battery is out of power Over weight
Driving on uneven road| Change the battery Charge the battery again Lighten the weight to less than 30Kg Driving on flat road
| The gear is broken| Bring it to repair
The car shakes when it goes forward| Bad connection of the motor connector wires Something wrong with the motor| Connect the wires well Bring it to repair
Drive without music| There isn’t battery in the steering wheel| Put the battery
If you can’t solve the problem, please contact us.

Kind reminder

  • Before the first use, make sure that the battery has been charged over 12hours, otherwise it will be damaged forever.
  • Do not drive the car on the slipped street, road, slop and other dangerous places.
  • Do not drive the car on the smooth surface, such as marble and floor tile. The car is only for one person.
  • Do not be overweight. The maximum load is 30Kg
  • Do not transfer the switch from “Forward” to “Backward” during the advance.
  • Do not change the line and model of charged device.
  • Keep the remote controler and the car away from the rain and fire.
  • When the car meets some obstacle, it will stop. The car will move again when the obstacle is removed.
  • Do not drive the car in the water. Do not put the water or liquid into the car.
  • Do not drive the car in the room to protect children and furniture.
  • When the battery is in low power, the car just go forward, but not drive left or right. When it can’t go or shake, you should change the new battery at once.
  • Please turn off the power when the car is not driven. If the car is not driven for a long time, please plug out the battery connector.

Kind reminder for charging

  1. Make sure the battery has been charged over 12 hours before the first use.
  2. Connect the charger connector to the battery connector, then insert the charger on the plug.
  3. After using 1 hour, you should charge in time. It takes 8 to 12 hours to charge normally.
  4. Do not charge over 20 hours.
  5. It is normal to have some heat for charger and battery when it is charging. (low than 60°C)
  6. In order to protect charger, battery and circuit, please use the special charger and battery from the seller.
  7. The connecting terminal can’t be in short circuit.
  8. Make the battery charge once a month at least when the car is not driven for long time.
  9. Charge the battery by adults.

Chargers and battery maintenance:

  1. Take away the seat first, and urscrewing the battery cover,finally get out of or put in the battery,and then screwing the battery cover,finally put the seat as well as screwing the bolt.
  2. Must be charged under Adults’ inspection.
  3. Battery poles must be connected correctly,(Red to Red, Black to Black) 4.Being short circuit is not allowed.

Battery using maintenance:

Battery for remote control

  1. Please use two pieces of 1.5VAA batteries.
  2. Open the battery cover and insert two1.5VAAA batteries, then close the cover; Remove the battery in the same way.
  3. Either different styles of batteries or new and old batteries can’t be used together.

Battery for the car

  1. Battery poles must be connected directly.
  2. Not allow short circuits.

Maintenance:

  1. Before the installation,make sure the parts are complete, If you have any questions,please feel free to contact us.
  2. Make sure every part is complete when installing and using.
  3. Please clean the product regularly. Do not damage to the electrical equipment.
  4. Please check and maintain the car for the children’s safety.

EXECUTION STANDARD : EN 71 EN62115
ASTM F963 CPSIA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals