EVERINT IDRO900ME-L3 UHF RFID Reader Module User Manual

September 25, 2024
EVERINT

IDRO900ME-L3 UHF RFID Reader Module

Product Information

Specifications:

  • Model: IDRO900ME-L3

  • Company: EVERINT

  • Date: September 13, 2024

  • Version: V24.09.13

  • FCC Certification: Part 15 of FCC Rules

  • Compliance: FCC RF exposure limits for an uncontrolled
    environment

  • Installation: OEM integrators only

Product Usage Instructions:

FCC Certification Requirements:

This device complies with part 15 of the FCC Rules. It must not
cause harmful interference and must accept any interference
received.

Exposure to Radio Frequency Radiation:

To comply with FCC RF exposure compliance requirements, maintain
a separation distance of at least 20 cm between the antenna and all
persons.

OEM/Integrators Installation Manual:

The equipment is intended for OEM integrators who are
responsible for proper installation and operation. Follow the
specified conditions regarding installation distances and
transmitter usage.

Instructions to the OEM/Integrator:

The OEM integrator must include required statements in the user
manual and address operating conditions for RF exposure compliance.
Provide guidance to the host manufacturer for compliance with part
15b requirements.

Device Conditions for Use:

The equipment should be installed and operated with a minimum
distance of 20 centimeters between the radiator and the body. The
transmitter must not operate with any other antenna or
transmitter.

Modular Approval:

The module has been granted modular approval for mobile
applications. Additional FCC approvals may be required based on the
host product’s evaluation for simultaneous transmission
requirements.

FAQ

Q: Who is responsible for ensuring compliance requirements with

the device installed?

A: The OEM integrator is responsible for testing their
end-product for any additional compliance requirements with the
device installed.

Q: What are the FCC certification requirements for this

device?

A: The device complies with part 15 of the FCC Rules, ensuring
it does not cause harmful interference and accepts any interference
received.

IDRO900ME-L3 USER’S MANUAL
V24.09.13
September 13, 2024

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

Revision history

Version V24.09.05 V24.09.13

Revision Date 2024-09-05 2024-09-13

Revision Page

Revision Description 1st Edition Added certification requirements

2

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

FCC Certification Requirements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Caution THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Any Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
IMPORTANT NOTE : FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
OEM/ integrators Installation Manual the modules limited to OEM installation only the OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Instructions to the OEM/integrator The OEM integrator must include the instructions or statements required by part 15.19 and 15.21 in the user manual. the OEM integrator must include a separate section in the host user’s manual concerning the operating conditions to satisfy RF exposure compliance. there is requirement that the grantee provide guidance to the host manufacturer for compliance with part 15b requirements.
3

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

This device is intended only for OEM integrators under the following conditions: (1) This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. (2) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this device installed.
This module has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC certification if they meet the following conditions. Otherwise, additional FCC approvals must be obtained. The host product with the module installed must be evaluated for simultaneous transmission requirements.
The user’s manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, use this module only with the included onboard antenna.
The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.
These modules are designed to comply with the FCC single modular FCC grant
– End Product Labeling To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: 2AKMF-IDRO900ME-L3
– Manual Information to the End User The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module. The end user manual shall include all required regulatory information/warning as show in this manual.

4

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

IC Certification Requirements
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. -connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
RF Radiation Exposure Statement: This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (AF) Exposure rules as this equipment has very low levels of RF energy. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
5

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

RSS-102 RF Exposure Lantenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la source de radiation (l’antenne) et toute personne physique. Cet appareil ne doit pas être installé ou utilisé en conjonction avec une autre antenne ouémetterur.
IMPORTANT NOTE This device complies with FCC & ISED radiation exposure limits set forth for an uncontrolled environment. This device should be installed and must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions: 1) This module may not be co-located with any other transmitters or antennas. 2) The antenna must be installed such that 20cm is maintained between the antenna and users. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC & IC authorizations.
– End Product Labeling To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: 2AKMF-IDRO900ME-L3
IC: 22266-IDRO900MEL3
– Manual Information to the End User The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module. The end user manual shall include all required regulatory information/warning as show in this manual.

6

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

NCC warning statement

LP0002_3.8.2:

7

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

Contents
1. Introduction & System composition diagram ………………………………………………….9 Introduction………………………………………………………………………………………………………………………………9 System composition diagram……………………………………………………………………………………………..9
2. Composition parts …………………………………………………………………………………………. 10 3. Reader Description ………………………………………………………………………………………… 11 4. Reader Specification ………………………………………………………………………………………. 13
Reader Performance (KOREA, USA, EUROPE, etc) ……………………………………………………. 13 Interface………………………………………………………………………………………………………………………………….. 13 Physical Dimension……………………………………………………………………………………………………………… 13 Channel number & Frequency table……………………………………………………………………………… 14 Mechanical Dimension ………………………………………………………………………………………………………. 15

8

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

1. Introduction & System composition diagram

Introduction
– The IDRO900ME-L3 is a compact size RFID reader module developed for the embedded reader market, which comprises printers, industrial PDA, and similar devices. It provides customers with compact size, low cost, high performance functions. It supports protocols of ISO18000-6C(EPC C1G2), and it interfaces with a host system via UART.
– Target Application
PDA type RFID Reader RFID Printers / Tag Encoders USB Readers Smart-Shelves
System composition diagram

IDRO900ME

9

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

2. Composition parts

RFID Reader module

Interface Cable
ANTENNA(6dBi) (option)
UART to USB Convertor (option)
Reader Software & User Document
10

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

3. Reader Description
Status LED

DATA LED : The Red LED will twinkle when the reader is receiving data from a tag.
ANT Port
ANT Port : Connect RF Cable to reader module and ANT
Interface connector : Supply voltage and interface with a host system(PC, PDA…) via UART.
11

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

Interface Pin-map

1

VCC (3.8 ~ 4.2V, typ 4V)

2

VCC (3.8 ~ 4.2V, typ 4V)

3

GND

4

GND

5

GND

6

TXD (IDRO900ME HOST)

7

RXD (IDRO900ME HOST)

8

PWR_ON

9

BAT ADC

10

GPIO_1

11

UART_RTS

12

UART_CTS

12

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

4. Reader Specification

Reader Performance (KOREA, USA, EUROPE, etc)

Item MODEL Architecture Protocol RF Chipset Frequency
Max Tx Power Power Control Hopping Channels Channel Spacing

Specification IDRO900ME-L3 UHF RFID Reader Module EPC Gen2 (ISO 18000-6C)
IMPINJ E310 917.3MHz to 920.3MHz(Korea) 902.75MHz to 927.25MHz(USA) 922.25MHz to 927.25MHz(ROC) 860MHz to 930MHz (Customizable)
30dBm±0.5dBm (1W) 5dBm to 30dBm (1dB step) 6 (Korea), 50(USA), 4(EUROPE), 11(ROC)
600KHz (Korea, EUROPE), 500KHz(USA, ROC)

Channel Dwell time Modulation Method
Supply Voltage

< 0.4 seconds PR-ASK
3.8 ~ 4.2V (typ. : 4V)

Maximum Current (@ max. power) Tag Read Distance (max.) Operating Temperature LED Indicators Firmware version

< 1.6A < 10m -10 to +85 Supply voltage, Reading the Tag(Blink) V240529B

Interface

Host connector

Part No. : 12505WR-12 Manufacturer : Yeonho Electronics

ANT Connector

Part No. : CMJ-S00 Manufacturer : Giga Lane

Physical Dimension
SIZE Weight

35.8mm × 40.5mm × 7.4mm 16g

13

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

Channel number & Frequency table

Channel No.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

KOREA
917.3 917.9 918.5 919.1 919.7 920.3

USA
902.75 903.25 903.75 904.25 904.75 905.25 905.75 906.25 906.75 907.25 907.75 908.25 908.75 909.25 909.75 910.25 910.75 911.25 911.75 912.25 912.75 913.25 913.75 914.25 914.75

EUROPE
865.7 866.3 866.9 867.5

ROC
922.25 922.75 923.25 923.75 924.25 924.75 925.25 925.75 926.25 926.75 927.25

Channel No.
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

USA
915.25 915.75 916.25 916.75 917.25 917.75 918.25 918.75 919.25 919.75 920.25 920.75 921.25 921.75 922.25 922.75 923.25 923.75 924.25 924.75 925.25 925.75 926.25 926.75 927.25

14

IDRO900ME-L3 User’s Manual

Company EVERINT

Date 2024-09-13

Version V24.09.13

Mechanical Dimension

15

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals