SCANGRIP 03.6208 Uniform For Life Work Light Instruction Manual
- September 26, 2024
- SCANGRIP
Table of Contents
SCANGRIP 03.6208 Uniform For Life Work Light
Specifications
- Model: 03.6208
- Warranty: 5 years
- LED design with 32 LEDs
- 3 brightness levels
- Light Output: 50-500 lumens (Spot: 175 lumens)
- Battery: 3.7V / 2600mAh Li-ion
- Operating Time: 3.2 W
- IP65-rated (dust and water-resistant)
- Rough service and IK07 impact resistance
- Dimensions: 188 x 60 x 33 mm / 7.4 x 2.36 x 1.3 in
- Weight: 263 g / 0.58 lbs
Product Usage Instructions
Charging Instructions and Battery Tips:
- Before first use, fully charge the battery. The red indicators will flash during charging.
- If the highest indicator doesn’t flash, it may be due to temperature constraints.
- All red indicators stay on when fully charged. Use only original batteries.
- Avoid leaving the battery uncharged for extended periods to prevent deep discharge.
Usage:
Ensure the battery is charged before use for optimal performance and longevity.
Spare Parts:
Extend the lifespan of your product by using available spare parts from scangrip.com.
FAQ
- Q: How do I register for the warranty?
- A: Read the terms and register on scangrip.com to activate your 5-year warranty.
- Q: What should I do if the lamp stops working?
- A: If the lamp reaches the end of its life, replace the entire lamp for continued functionality.
- Q: How do I dispose of the battery and device?
- A: Remove the battery before disposal and follow local recycling guidelines for safe disposal of electrical products.
5 warranty years
Read the terms and register on scangrip.com to activate your warranty
Features
Product Overview
WARNING
- Avoid looking directly into the beam of light, as this will result in dazzling.
- Do not use the lamp near a naked flame.
- The light source of this lamp is not replaceable. When the light source reaches its end of life the whole lamp must be replaced
CHARGING INSTRUCTION AND BATTERY TIPS
- Only charge the lamp indoors at 5 °C to 40 °C / 41 to 104 °F.
- Before using the lamp for the first time, the battery must be fully charged.
- The red charging indicators light up with the highest flashing during charging.
- The highest charging indicator will not be flashing if the temperature does not allow charging.
- The red charging indicators will all be constantly on when fully charged.
- Always replace the battery with an original battery.
- Do not leave the battery without charge for an extended period.
- Deep discharge risks damaging the battery.
USE
- To turn the lamp on or off, press the power button (A).
- Press and hold the power button (A) to turn on the spotlight.
- Press the brightness button (B) to turn on the lamp in OPTILIGHT mode.
- The OPTILIGHT indicator will turn on.
- To increase or decrease the brightness, press the brightness button (B).
- When the brightness is changed, the new value is saved, and the lamp will start at that level the next time it is turned on.
- When the battery is below 10 %, the lamp will flash 3 times every 2 minutes.
- If the lamp temperature is too high or low, the lamp will turn off and flash all battery indicators 10 times.
SPARE PARTS
- With convenient access to spare parts, users can extend the lifespan of our products and ensure long-lasting functionality.
- Find available spare parts on scangrip.com
Discarded electrical products must not be disposed of together with household waste. Please use recycling facilities. Ask your local authority or retailer for advice on recycling.
-
The battery must be removed from the device before it is broken up.
-
The device must be disconnected from the mains when the battery is removed.
-
Please dispose of the battery safely
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>