MCOHOME PM2.5 Monitor User Manual
- June 3, 2024
- MCOHOME
Table of Contents
MCOHOME PM2.5 Monitor
Introduction
MCOHome PM2.5 Monitor is an air quality controller which compatible with Z-Wave technology, it is mainly used to monitor PM2.5 concentration in industrial, agricultural, and residence environment, while monitoring the indoor temperature and humidity. Device can be included into any Z-Wave network, and is compatible with any other Z-Wave certified devices.
Specification
- Power Supply :DC12V
- Self dissipation: <3W
- PM2.5 detection range: 0-999ug/m3
- Temperature range： -9.0～50 ℃
- Humidity range : 0%～99% RH
- Dimension： 85 13533mm
- Hole Pitch： 60mm or 82mm
- Installation: wall-mounted (Vertical)
- Housing: Tempered glass+ PC Alloy
- Z-Wave Frequency: 868.42MHz (EU)
Safety Information
To protect yourself and others from danger and to protect the device from
damage, please read the safety information before using it.
Important!
- A qualified electrician with the understanding of wiring diagrams and knowledge of electrical safety should complete installation following the instructions.
- Before installation, please confirm the real voltage complying with the device’s specification. Cut off any power supply to secure the safety of people and device.
- During installation, protect the device from any physical damage by dropping or bumping. If happens, please contact the supplier for maintenance.
- Keep the device away from acid-base and other corrosive solids, liquids, gases, to avoid damage.
- Avoid overexertion during operation, to protect device from mechanical damage.
- Read all instructions and documentation and save for future reference.
Installation & Wiring
Location:
Device is suggested to be installed indoor, a place with around 1.5m height
above the floor where represents the average PM2.5 concentration. It should be
away from direct sunlight, any cover, or any heat source, to avoid false
signal for detection.
Notice!
- Device must be wall-mounted vertically. Do not lay it flat or upside down while working.
- Do not mounted it in a wind gap, or cover its bottom, which may affect the detected data.
- Step 1: Follow the wiring diagram to insert all wires into right terminals and tighten screws.
- Step 2: Separate panel and bottom case by removing the screw at the bottom of device, and mount the bottom case onto wall with two screws (M4*25mm). The hole pitch 60mm is for 86/60mm box, and 82mm is for American 120mm box.
- Step 3: Mount the panel back by aligning its tabs and card slot onto the bottom case.
- Step 4: Tighten the fastening screw and the device is ready for normal work.
Button & Display
Operation
Local time setting
In normal display interface, long press S3 will enter the local time
modification interface. Press S2 can switch among “Week, Hour & Minute “,
press S1 or S3 can change their values. After all parameters set, press S2 can
save settings and return to normal display.
Backlight
The backlight will be full bright when any keys pressed, and turn to half
bright if no operation in10 Sec.
Including & Excluding of Z-Wave network
Activate Inclusion/Exclusion mode in the gateway. When device powered on, long
press S1 & S3 synchronically to enter interface for inclusion or exclusion of
Z-Wave network.
- If device has not been included into any Z-Wave network before, “- – -” will display on the screen.
- Then press S1 once, “- – -” flashing and device enters into learning mode to get a node ID. If inclusion is success, a node ID will display on the screen. If not, “- – -” will stop flashing in 20 sec.
- If a node ID displays, it means the device is already in a Z-Wave network. To press S1 once can remove it from the network. “- – -” displays and press S2 once can return to normal work.
Note: If display flashing, long press S1+S3 can quite the operation and
back to normal work. If display stops flashing, press S2 once can return to
normal work. Association Group
Device supports 1 association group. A gateway is suggested to associate with
this group. The device will report to this associated device (gateway) when
detected data changes:
PM2.5: report every 10Sec
Temperature: report when any change≥ 0.5℃ Humidity: report when any change≥ 2%
Command Class supported by the device
- COMMAND_CLASS_BASIC;
- COMMAND_CLASS_SENSOR_MULTILEVEL;
- COMMAND_CLASS_ASSOCIATION;
- COMMAND_CLASS_VERSION;
- COMMAND_CLASS_MANUFACTURER_SPECIFIC
1-year Limited Warranty
MCOHome warrants this product to be free from defects in material and
workmanship under normal and proper use for one year from purchase date of the
original purchaser. MCOHome will, at its option, either repair or replace any
part of its products that prove defective by reason of improper workmanship or
materials. THIS LIMITED WARRANTY DOES NOT COVER ANY DAMAGE TO THIS PRODUCT
THAT RESULTS FROM IMPROPER INSTALLATION, ACCIDENT, ABUSE, MISUSE, NATURAL
DISASTER, INSUFFICIENT OR EXCESSIVE ELECTRICAL SUPPLY, ABNORMAL MECHANICAL OR
ENVIRONMENTAL CONDITIONS, OR ANY UNAUTHORIZED DISASSEMBLY, REPAIR OR
MODIFICATION. This limited warranty shall not apply if: (i) the product was
not used in accordance with any accompanying instructions, or (ii) the product
was not used for its intended function. This limited warranty also does not
apply to any product on which the original identification information has been
altered, obliterated or removed, that has not been handled or packaged
correctly, that has been sold as second-hand or that has been resold contrary
to Country and other applicable export regulations.
www.mcohome.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>