BREARO Pressure Washer Hose Reel Instructions
- September 25, 2024
- BREARO
Table of Contents
Pressure Washer Hose Reel
“`html
Product Information
Manual Pressure Washer Hose Reel
Specifications:
- Capacity: 100 feet of 3/8 hose
- Inlet: 3/8 NPT
- Outlet: 3/8 NPT
- Maximum Pressure: 4000 PSI
Product Usage Instructions
Safety Precautions:
-
Make sure incoming pressure does not exceed the rated
pressure. -
Use proper eye protection when assembling and using the hose
reel. -
Assemble the hose reel on a clean workbench free of debris and
moisture. -
Use soap and water when checking for air leaks.
-
Keep children away from the work area.
Warning: Exposure of skin directly to
pressurized air or fluids could result in severe bodily injury.
Scan the code to watch the operation video.
Frequently Asked Questions (FAQ)
Q: What should I do if the hose reel is leaking?
A: Check all connections for tightness and ensure there are no
damages to the hose. If leaks persist, contact customer support for
assistance.
Q: Can I use this hose reel with hot water?
A: It is recommended to only use this hose reel with cold water
to prevent damage and ensure longevity of the product.
Q: How should I store the hose reel when not in use?
A: Store the hose reel in a cool, dry place away from direct
sunlight and extreme temperatures to maintain its quality.
“`
Manual Pressure Washer Hose Reel Instructions
Read and understand the entire manual before assembling or using a hose reel.
Failure to comply with instructions or warnings may result in personal injury
and/or property damage. Specifications: Capacity: 100 feet of 3/8″ hose Inlet:
3/8″ NPT Outlet:3/8″ NPT Maximum Pressure:4000 PSI
Safety Precautions 1. Make sure incoming pressure does not exceed the rated
pressure. 2. Use the proper eye protection when assembling and using the hose
reel. 3. Assemble the hose reel on a clean workbench free of debris and
moisture. 4. Use soap and water when checking for air leaks. 5. Keep children
away from the work area. Warning: Exposure of skin directly to pressurized air
or fluids could result in severe bodily injury.
Installation And Assembly Note: You will need to purchase appropriate hardware
for mounting your new reel. Holes have been provided in the reel base, for
mounting on a suitable flat surface. You will also need to supply hose for the
reel. Refer to specification information to determine the correct hose length.
Refer to appendix for assembly. 1. Match handle to 3 holes in reel flange.
Attach using 3 screws, nuts Note: Nuts must go on handle side of flange. 2.
Put the bolts ( 3/8″ or 10mm) through 4 holes in the base of the hose reel and
tighten it to ceiling wall/floor so reel can be fastened into position. 3.
Apply Teflon tape or thread sealant to reel’s built in supply hose fitting.
Then attach this supply hose to the outlet of power source. 4. Apply Teflon
tape or thread sealant to hose fitting threads. Attach to the reel swivel
valve, then feed the rest of hose through the flange opening. 5.To avoid
damaging the swivel valve, make sure to use an appropriate wrench to stabilize
the swivel hosing tightening the hose fitting. 6. Hose length should be 100
feet or less. 7. Use the red buckle to fix the position of the hose. If you
have any questions, please contact us at any time : contact us:
service@forsupports.com.
Scan the code to watch the operation video
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>