GILKON FP4 Wall Mount For Flat Panel Display Installation Guide

: September 24, 2024
: GILKON

Table of Contents

FP4 Wall Mount For Flat Panel Display
Specifications:
Product Usage Instructions:
Step 1 – Parts Audit
Step 2 – Primary Parts Audit
Step 3 – AV Mount Assembly

FP4 Wall Mount For Flat Panel Display

“`html

Specifications:

Weight: 34.8 kg
Linear Actuator Stroke: 500mm

Product Usage Instructions:

Step 1 – Parts Audit

Make sure you have all the parts listed:

Big Allen Key (4mm)
Allison Allen Key (5mm)
Small adjustable wrench (not supplied)
Spirit level (not supplied)

Also, ensure you have suitable wall fixtures for your wall
type.

Step 2 – Primary Parts Audit

Sort the primary parts on a flat surface:

FP4-24 Base Support Bracket x1
FP4-25 Top Actuator Support Channel x1

Step 3 – AV Mount Assembly

Follow these steps:

Gather the components listed in the drawing.
Check for specific orientation as indicated in the
diagrams.
Attach components using M8 x 20 Socket Head Cap Screws, Hexagon
Nuts, and Flat Washers as required.

FAQ:

Q: What should I do if I am missing a part?

A: Contact customer support at (02) 47286111
for assistance in obtaining the missing part.

Q: How do I adjust the height of the wall mount with
Power Lift?

A: Use the provided Linear Actuator with a
500mm stroke to easily raise and lower the wall mount to your
preferred viewing height.

“`

INSTALLATION GUIDE
FP4 Wall MOUnt for flat panel Display

Hi I m
Here to help
All speciications are subject to change without notice
© Copyright 2024 OPIE Manufacturing Group PTY Limited. All rights reserved.

opiegroup·com·au

(02) 47286111

02/18

109 RusselL Street, Emu HEIGHTS NSW 2750

*AV Monitor screen not included
WWW·GILKON·COM·AU
GILKON is a part of the OPIE GROUP

FP4 WALL MOUNT – Assembly Instructions
IF YOUR READING THIS THEN YOU ARE ON THE RIGHT STEP TO BEGIN
Thank you for purchasing the Gilkon FP4 WALL MOUNT with Power Lift. ” Hi! I am ‘OP’ and I’m here to help you assemble it – Careful lifting, it weighs 34.9kg”
Hi I m
Here to help
960 107
885

100 40
1548

1500 400

111
WEIGHT: 34.8 kg

FP4 WALL MOUNT – Assembly Instructions

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
WITH POWER LIFT
The Gilkon FP4 Wall Mount includes the “Power Lift” and can be easily raised and lowered to your preferred viewing height.

*AV Monitor screen not included

FP4 WALL MOUNT – Assembly Instructions

*AV Monitor screen not included

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
STEP 1 – PARTS AUDIT
Make sure you have got all the parts listed and take note of the sizes and sort – We have supplied 2 trusty Allen Keys.
We call them “Big Allen”, and “Allison”.
You will also need to have YOUR OWN small adjustable wrench and spirit level, plus suitable wall fixtures for your wall type.

A
M8 x 75 Cup Head Bolt ZP
x1

B M8 x 65 Cup Head Bolt ZP
x7

C
M8 x 25 Button Head Cap Screw ZP
x19

D
Hexagon Nut M8 Z/P
x16

E
Hexagon Nut M6 Z/P
x2

F
Nyloc Lock Nut M8 Z/P
x8

G
Nut Wing Zinc M6-1.00
x2

H
Flat Washer M8 Z/P
x44

SCREEN MOUNTING PACK (PACKED SEPARATELY)

“I am Allison”

VIEW SCALE ( 1 : 1 ) ALL FASTENERS
“I’m a Power lift! ”

M8 x 25 Button Head Cap Screw ZP M6 x 16 Button Head Cap Screw ZP

Flat Washer M8 Z/P
x4

Flat Washer M6 ZP
x4

“BIG AllEN” >>

4mm Allen Key

5mm Allen Key

Linear Actuator (500mm Stroke)

I Flat Washer M6 ZP
x2
Small Adjustable Wrench (Not supplied)
Spirit Level (Not supplied)
REQUIRED TOOLS

FP4 WALL MOUNT AV STAND – Assembly Instructions

NOTE: Packaged contents may look different to content shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
STEP 2 – PRIMARY PARTS AUDIT
Please sort the FP4 Wall Mount primary parts on a clear flat surface and take note of
the pressed arrows and their orientations on Frame Parts as they are important.

1
FP4-24 Base Support Bracket
x1

2
FP4-25 Top Actuator Support Channel
x1

3
FP4-27 Bottom Actuator Support Channel
x1

FP4-31 V-Slide Inner
x2

FP4-30 V-Slide Outer
x2

6
FP4-32 Screen Mount Frame
x1

7
FP4-33 Screen Mount Bkt
x2

8
FP4-34 Lock Bkt
x2

10
FP4 WM-36 Top Wall Fixing Bkt
x1
9

FP4-22 Leg 1755 Long
x2

11
FP4 WM-37 Bottom Wall Fixing Bkt
x1

FP4 WALL MOUNT – Assembly Instructions

NOTE: Packaged contents may look different to contents shown in diagrams

CopyrigChotp©y2ri0g2h4t ©O2P0IE2M4 aOnPuIEfaMctaunruinfgacGturoriunpg Group

FP4 WALL MOUNT – Assembly Instructions
STEP 3 – AV MOUNT ASSEMBLY

4 5 Please Note: Check Parts

arrows on the drawing that indicate spe-

cific orientation match the drawing indi-

cated pointing to the screen side.

1. Gather the components listed in the
drawing, including:
E M8 x 20 Socket Head Cap Screw x12 F Hexagon Nut M8 Z/P x 12 J Flat Washer M8 Z/P x24 3 Bottom Actuator Support Channel 4 V-Slide Inner 5 V-Slide Outer 6 Screen Mount Frame

2. Create the side assembly by attaching
4 V-Slide Inner inside V-Slide Out5 er for left and right with screws E F J and nuts and washers at the 3 corners of the Screen Mount Frame
(performed concurrently).

6 3. Screen Mount Frame attaching it to

4 5 the left and right V-Slides

the corners by inserting the screws
E through the designated holes and

fastening them with the corresponding
F J nuts and washers .

4. Secure the Bottom Actuator Support

3 4 Channel to the left and right

4 5 V-Slide

the corners of part

E by inserting the screws through

the designated holes and fastening
F them with the corresponding nuts J and washers .

Take a big, deep breath and plan your steps – check that the arrows are facing the right way!

Assembly
6
5 C

4
Assembly

Finished

3
FP4-27 Bottom Actuator Support Channel
x1

100

FP4-31 V-Slide Inner
x2

H D

C
M8 x 25 Button Head Cap Screw ZP
x12

( 1 : 3 )
D Hexagon Nut M8 Z/P
x12

ARROWS POINT TO SCREEN SIDE
H Flat Washer M8 Z/P
x24

6
FP4-32 Screen Mount Frame
x1

5
FP4-30 V-Slide Outer
x2

Excellent Work! In finishing this step you have completed the AV Mount Assembly

FP4 WALL MOUNT – Assembly Instructions

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
STEP 4 – FP4 SLIDER ASSEMBLY

Please Note: Look for arrows on parts that indicate specific orientation and match the direction indicated.
1. Gather components listed in the drawing, including:
c M8 x 65 Cup Head Bolt Z/P (x4) D Nyloc Lock Nut M8 Z/P (x4) H Flat Washer M8 Z/P (x4) 9 Leg 1755 Long 1 Base Support Bracket
2. Begin by aligning the Leg 1755
9 Long to the Base Support 1 Bracket .
3. Insert the M8 x 65 Cup Head Bolts
B through the designated holes 9 in Leg 1755 Long , ensuring
they are properly aligned.
9 4. Secure the Leg 1755 Long with H B Flat Washers on the bolt
before securing them with the
F nuts to provide additional
support and prevent damage to the
1 Base Support Bracket .

Assembly
B 9
H 1
F
( 1 : 8 )

Finished

1
FP4-24 Base Support Bracket
x1

9
FP4-22 Leg 1755 Long
x2

B M8 x 65 Cup Head Bolt ZP
x4
H Flat Washer M8 Z/P
x4

F
Nyloc Lock Nut M8 Z/P
x4

Fantastic! In doing this step you are half way to assembling the Slider.

FP4 WALL MOUNT – Assembly Instructions

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT STAND – Assembly Instructions
STEP 5 – WALL MOUNT ASSEMBLY TO SLIDER ASSEMBLY

Let’s put it all together and let it stand ready to move up and down

4 5 Please Note: Check Part &
arrows on the Wall Mount Assembly that indicate specific orientation match the arrows on the “Stand Slider Assembly”
1. Gather the necessary components listed in the drawing, including:
B M8 x 65 Cup Head Bolt Z/P (x2) F Nyloc Lock Nut M8 Z/P (x2) H Flat Washer M8 Z/P (x2) 2 Top actuator support channel
+ Wall Mount Assembly(complete) + Slider Assembly (complete)
H H 2. Place the Washers on the B bolts before securing the 2 Top actuator support channel
To the top of the Wall Munt
B Assembly secure with M8 bolts
F H & Nyloc nuts and washers .
3. Carefully Slide the completed Wall Mount Assembly down the Slider Assembly until it comes to a resting point, Checking orientation of the arrows to match indicated direction.

Assembly

H F
Assembly

Finished

FP4-25 Top Actuator Support Channel
x1

ARROWS POINT TO SCREEN SIDE
It should look like that picture there
Slide lifter frame on to the Wall Mount Frame ensuring direction of arrows align. Allow to rest at bottom of frame. Attach Top Actuator Support Channel to the top of the completed Wall Mount Frame with 2x M8 x 65 Cup Head Bolts , 2x Flat Washers M8 , and 2x Nylock Lock Nuts

B M8 x 65 Cup Head Bolt ZP
x2
F Nyloc Lock Nut M8 Z/P
x2
H Flat Washer M8 Z/P
x2

It would be even easier to raise and lower with a Power Lift!… Let’s install it next!

FP4 WALL MOUNT – Assembly Instructions

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
STEP 6 – POWER LIFT INSTALLATION

Place bolt B into the center hole on the Top actuator support channel 2 and fix the Power lift actuator j on the rear side of the WALL MOUNT ASSEMBLY.
Fix the bottom of the Power lift Actuator with Bolt A. Use H washers and Nyloc Nuts F as indicated to secure the Power lift Actuator j to the bolts A and B.
Tighten with your Spanner!

Let’s install Power Lift next!
B

H F

A
M8 x 75 Cup Head Bolt ZP
x1

A F
H
( 1 : 8 )

M8 x 65 Cup Head Bolt ZP

Linear Actuator (500mm Stroke) VIEW SCALE ( 1 : 6 )

F
Nyloc Lock Nut M8 Z/P
x2

Flat Washer M8 Z/P
x2

Now it needs the power cord!

FP4 WALL MOUNT AV STAND – Assembly Instructions

NOTE: Packaged contents may look different to content shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
STEP 7 – POWER LIFT LOOM ASSEMBLY
Click Plugs and Sockets: Some sockets come with locking mechanisms to hold the connection. Match the Locking Sockets with the plugs correctly and join; listen for a “click” sound to ensure the connection is secure.
Plug into 240V: Ensure that the power source you are plugging into is a 240V outlet. Testing with Controller: Before operating the equipment, test the lift with the wired Controller. Press the Up and Down
buttons to verify that the lift functions correctly and responds to the controller’s commands.

It really is just click and play!

Power Lift

Controller

Transformer Plug
“CLICK”

Locking Socket
“CLICK”

240V plug

Transformer

Always follow safety guidelines when working with electrical equipment. Avoid touching exposed wires, ensure proper grounding, and use insulated tools when necessary. If you are unsure about any step, consult a professional electrician for assistance.

Plug
tYhoeuPhoawveer!

Locking Socket”CLICK”
Plug
“CLICK”
Plug Locking Socket

FP4 WALL MOUNT – Assembly Instructions

Time to get your monitor unpacked and face down ?

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
STEP 8 – INSTALL LOCKING BRACKET AND MONITOR BRACKET

Locking Bracket 8: Slide Locking Bracket 8 at the bottom of the Screen Mount Brackets 7 and secure with Wing Nut g and washers I (Leave Locking Bracket 8 in open position).
Screen Mount Brackets 7: Attach the two Screen Mount Brackets 7 to your monitor or screen using instructions provided with your
Monitors accompanying manual. Use the appropriate screws, nuts, and washers from the Screen Mounting Pack
7 for installation to your monitor.

Lay your monitor screen face on a blanket!

CIRCLED FASTENERS TO SUIT INSTALLED SCREEN

7 8 G I

FP4-34

Lock Bkt

FP4-33 Screen Mount Bkt
x2

Finally

get or

to use “little Allison

Al”

G
Nut Wing Zinc M6-1.00
x2

FP4 WALL MOUNT – Assembly Instructions

( 1 : 7 ) LOCK BRACKET IN OPEN POSITION

I Flat Washer M6 ZP
x2

So close now, it’s exciting, isn’t it?

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
STEP 8 – INSTALL LOCKING BRACKET AND MONITOR BRACKET

A Brackets:

Fix the Bottom Wall Fixing Bracket ß 200mm from floor, ensure you use the correct wall fixings for your specific wall type. Secure the Top Wall fixing bracket 0 to the top of the FP4 frame (see figure S)

S Positioning: Carefully lift and place your Gilkon FP4 wall Mount assembly into the Bottom Wall Fixing Bracket ß
raising it flush with the wall (Mark its fixing position on the wall with the top bracket).

D Final Fix: Once satisfied,secure the Gilkon FP4 wall Mount assembly in the correct position using the correct
wall fixture for your wall type (not provided), utilizing the Top Wall Fixing bracket 0.

A
PLEASE NOTE: Carefully plan how you will position the frame to wall and assess its suitble location to power.
Assess your wall type and obtain the correct wall fixings (not supplied) for your wall.

MID LINE

S C H

10
H D

D
MARK WALL USING SUITABLE SLOTS IN TOP BRACKET
SCREW TOP WALL FIXING BRACKET TO WALL USING SUITABLE SCREWS OR BOLTS (NOT PROVIDED)

Calculate your wall fixing capacity to hold an FP4 wall mount frame weight of 34.8 kg plus your flat panel weight combined.

WALL

To ensure it is level – use a level. (not supplied)

ENSURE BOTTOM WALL FIXING BRACKET IS LEVEL

Level it all up

FLOOR

200

11
RECOMMENDED HEIGHT FROM FLOOR TO BOTTOM OF BRACKET SCREW BOTTOM WALL FIXING BRACKET TO WALL USING SUITABLE SCREWS OR BOLTS
(NOT PROVIDED)

H
C
FLOOR

FLOOR

10
FP4 WM-36 Top Wall Fixing Bkt
x1

11
FP4 WM-37 Bottom Wall Fixing Bkt
x1

D
Hexagon Nut M8 Z/P
x4

Flat Washer M8 Z/P
x11

C
M8 x 20 Socket Head Cap Screw
x7

Bet it looks great on your wall?

FP4 WALL MOUNT – Assembly Instructions

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
STEP 9 – POSITON FLAT SCREEN PANEL MONITOR
Vesa Mount: Confirm that your monitors brackets match the correct width of the Vesa Mount indicator holes. Mount Flat Panel Display: Position your flat screen panel monitor on your slotting to Vesa Mount indicator holes. Test Power Lifter: Plug the Power Lift Actuator 240V plug into Power to test and position your monitor
to preferred height.
Time to get some help to lift the flat panel display onto the Vesa Mount.

( 1 : 2 )

ENSURE TOP & BOTTOM HOOKS ARE ENGAGED WITH THE SCREEN MOUNT FRAME

FP4 WALL MOUNT – Assembly Instructions

( 1 : 2 )
Please note:
· Lower the Monitor to bottom position before installing the monitor on the Vesa Mount
· Ensure the Monitor is fixed and securely Locked with lock Brackets L & R

( 1 : 4 )
DETAIL VIEW SHOWING SCREEN LOCK BRACKET IN POSITION 8mm HOLE SUITS PADLOCK UP TO 7mm SHACKLE (PADLOCK NOT SUPPLIED)

NOTE: Packaged contents may look different to contents shown in diagrams

FP4 WALL MOUNT – Assembly Instructions
DIMENSIONS & PRODUCT DISPLAY

A RED

Congratulations on your assembly! Thanks for supporting Australian Manufacturing

USTRALIAN N
UFACTU

“YOFUoTrAVrpoeunattMisnEtg”ar

Dimensions
960 885

Yahooooo!

1548

WEIGHT: 34.8 k

Well done! – Enjoy your FP4 Wall Mount for flat panel display!

FP4 WALL MOUNT – Assembly Instructions

NOTE: Packaged contents may look different to contents shown in diagrams

Read User Manual Online (PDF format)

Read User Manual Online (PDF format) >>

Download This Manual (PDF format)

Download this manual >>

FP4 Wall Mount For Flat Panel Display

Specifications:

Product Usage Instructions:

Step 1 – Parts Audit

Step 2 – Primary Parts Audit

Step 3 – AV Mount Assembly

FAQ:

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Related Manuals