Honeywell TP-G250 Portable Dehumidifier User Manual

Honeywell TP-G250 Portable Dehumidifier

Product Information

Specifications

• Brand: Honeywell

• Type: Portable Dehumidifier

• Refrigerant: R32

• Customer Support: USA – 1-800-474-2147 | usinfo@jmatek.com
  CANADA – canadainfo@jmatek.com

• Website: www.HoneywellAirComfort.com

Product Usage Instructions

R32 Safety
It is important to note that this appliance uses a flammable refrigerant (R32). Any repair or maintenance involving flammable refrigerants should be handled by qualified personnel following manufacturer recommendations.

Transportation and Storage

1. Transport equipment in compliance with local regulations for flammable refrigerants.
2. Mark equipment according to local regulations.
3. Dispose of equipment with flammable refrigerants following national regulations.
4. Store equipment as per the manufacturer’s instructions to prevent damage and leaks.
5. Ensure storage package protection to prevent mechanical damage that could lead to refrigerant leaks.

Note: Do not dispose of the product with household waste. Recycle responsibly to protect the environment and human health.

FAQ (Frequently Asked Questions)
Q: Can I use this dehumidifier in a small room?
A: Yes, the portable dehumidifier is suitable for use in small rooms. Ensure proper ventilation for optimal performance.

THANK YOU
Thank you for purchasing a Honeywell Portable Dehumidifier. This User Manual is intended to provide you with important information needed to set up, operate, maintain and troubleshoot this product.

SAFETY RULES

WARNING — READ AND SAVE THESE INSTRUCTIONS BEFORE USING THIS PRODUCT.
The use of electrical products may create hazards that include, but are not limited to injury, fire, electrical shock. Failure to follow these instructions may damage and/ or impair its operation and void the warranty. In case there is any inconsistency or conflict between the English version and any other language version of the content of this material, the English version shall prevail.
When using electrical appliances, basic safety precautions should always be followed:

• DO NOT touch the dehumidifier or the electrical plug with wet hands.
• Check the household voltage to ensure it matches the appliance’s specification.
• Before operating, remove all packaging material and check for any damage that may have occurred during shipping.
• DO NOT operate any product with a damaged cord or plug.
• DO NOT use an extension cord with this appliance.
• DO NOT run power cord under carpeting, or cover it with rugs or runners. Keep the cord away from areas where it may be tripped over.
• Always power off and unplug the dehumidifier before emptying the water tank.
• The water collected in the tank must be discarded. The water should never be used for drinking. Always unplug the dehumidifier and remove the water from the water tank before cleaning, servicing or relocating the unit.
• Remove the power cord from the electrical receptacle by grasping and pulling on the power cord plug-end only, never pull the cord.
• This appliance has been manufactured for use in domestic environments and must not be used for other purposes.
• DO NOT use the product in areas where gasoline, paint or other flammable goods and objects are used or stored.
• This dehumidifier is designed for indoor residential applications only. It should not be used for commercial or industrial applications.
• DO NOT attempt to repair or adjust any electrical or mechanical functions of the dehumidifier, as this may cause danger and void the warranty.
• DO NOT cover the air inlet or outlet on the appliance as this may cause the unit to fail.
• DO NOT insert or allow objects to enter any ventilation or exhaust opening as this may damage the product and could cause electrical shock or fire.
• DO NOT let children play with this appliance, packaging or included plastic bag.
• If the unit is damaged or it malfunctions, do not continue to operate it. Unplug the product from the electrical outlet. Refer to the troubleshooting section and contact the customer support center.
• Always place the dehumidifier on a leveled floor.
• Never install the product near a bathtub or any water container.
• Store in a dry area, away from direct sunlight, when not in use.
• This appliance and its packaging materials are not intended for use by persons (including children or elderly) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning
• the use of the appliance by a person responsible for their safety.
• Always grip the top handle and keep the unit upright when transporting from room to room – DO NOT tilt the product on its side or upside-down.
• If the dehumidifier was transported tilted on its side, you must position it upright again and wait at least 4 hours before using it.
• WARNING: To reduce the risk of fire or electric shock, do not use this appliance with any solid state speed control device.

R32 SAFETY

Additional warnings for appliances with R32 refrigerant gas.

• Read the instructions carefully before using the appliance.
• R32 refrigerant gas complies with UL60335-2-40 / UL60335-1. This appliance contains a certain number of grams (see rating label at the back of the unit) of R32 refrigerant gas. The maximum refrigerant charge amount is not greater than R32 0.918 kg based on UL60335-2-40.
• When defrosting or cleaning, do not use any method other than those recommended by the manufacturer.
• Do not place the appliance in a room with continuous sources of ignition (e.g. open flame, operating gas appliance, or working electrical heater).
• Do not pierce and do not burn.
• Do not perforate any part of the refrigerant circuit.
• Refrigerant gas may be odorless.
• Accumulation of possible refrigerant leaks in an unventilated room could lead to fire or explosion should the refrigerant come in contact with electric heaters, stoves, or other sources of ignition. The appliance must be stored in a way to prevent mechanical damage and in a well-vented area.
• Only individuals authorized by an accredited organization certifying their competence to handle refrigerants in compliance with industry legislation should work on the refrigerant circuit. Servicing shall be performed only as recommended by the manufacturer.
• All working procedures that affect safety means shall only be carried by competent persons.

Repair must be performed based on the manufacturer’s recommendations. Maintenance and repair that requires the assistance of other qualified personnel must be performed under the supervision of specialists in the use of flammable refrigerants.

Transportation, marking, and storage for units.

1. Transport of equipment containing flammable refrigerants must comply with local transport regulations.
2. Marketing of equipment using signs must comply with local regulations.
3. Disposal of equipment using flammable refrigerants must comply with national regulations.
4. The storage of equipment should be in accordance with the manufacturer’s instructions.
5. Storage package protection should be constructed such that mechanical damage to the equipment inside the package will not cause a leak of the refrigerant charge.
6. The maximum number of pieces of equipment permitted to be stored together will be determined by local regulations.

This marking indicates that this product should not be disposed with other household waste throughout the US. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

HOW A DEHUMIDIFIER WORKS

When the dehumidifier is switched ON, a fan pulls moisture-laden air into the dehumidifier where it passes through dehumidifying coils inside the unit. These coils condense moisture from the air and collect it in the water tank. The dry air is then exhausted from the dehumidifier. The air flows through the air vents of the dehumidifier into the room as dry, warm air.
IMPORTANT: The dehumidifier is designed to operate between 41°F (5°C) and 89°F (32°C).
The dehumidifier’s performance may be greatly reduced if room temperature is beyond this temperature range.

SELECTING A LOCATION – IMPORTANT

Before using the dehumidifier, place the unit UPRIGHT for at least 4 hours before use to allow the refrigerant to stabilize in case it was transported on its side or upside-down.
For optimal efficiency, the dehumidifier must be operated in an enclosed area. Keep all doors, windows and other outside entrances to the room closed.

• Place the dehumidifier in an area where the temperature will not drop below 41°F (5°C)
• Place the dehumidifier at least 17.7 inches (45 cm) away from other objects (e.g. curtains or furniture) that may restrict airflow from the back or through the air vents of the unit.
• The dehumidifier must be positioned on a level floor.
• IMPORTANT: The effectiveness of the dehumidifier can be influenced by different factors. One factor is the rate at which new, moisture-laden air enters the room and the amount of air circulating in and out of the area to be dehumidified. For example, if a door to a basement is constantly opened, letting new, moisture-laden air into the room, dehumidification will take longer than if the door was kept closed. If the dehumidifier is in a room with a storage closet or cabinets, it will have little or no effect in drying the inside of the storage closet or cabinets unless there is adequate circulation of air in and out of these spaces. To dehumidify these spaces, open the storage door or cabinet doors to allow air circulation. You may find that installing a second dehumidifier may be required for larger enclosed areas.

UNPACKAGING THE DEHUMIDIFIER

This Dehumidifier is packaged with a colored or transparent tape to secure some parts during transportation. Remove the colored or transparent packaging tape from the unit.

1. Gently pull the water tank from out of the dehumidifier
2. Remove the splash guard from the top part of the water tank
3. Take out the power plug, drain hose and other accessories, which is placed inside the tank of the dehumidifier.
4. Once all accessories have been removed, replacethe splash guard onto the top part of the water tank. Make sure that the tank is properly positioned.

PARTS DESCRIPTION

1. Control Panel
2. Handle
3. Splash Guard
4. Water Tank Handle
5. Water Tank
6. Water Level Indicator
7. Casters
8. Dehumidified Air Exhaust Vent
9. Washable Dust Filter
10. Direct Drain Outlet
11. Direct Drain Cap
12. Mounting Holes for Cord Winders
13. Auto Drain Pump Outlet
14.  Auto Drain Pump Cap
15. Power Cord & Plug
16. Cord Winders
17. Continuous Water Drain Tube (Inner Dia.: 0.47 in; Length: 3.28 ft)
18. Auto Drain Pump Tube
    (Inner Dia.: 0.21 in; Length: 16.4 ft)

• THIS IS ONLY FOR MODEL TPFIT50PWK WITH BUILT-IN DRAIN PUMP

INSTALL THE CORD WINDER

Once you have removed the cord winder accessories from the water tank – follow the steps below.

1. Step 1: Line up the cord winder pieces to the mounting holes.
2. Step 2: Rotate 45-degrees clock-wise.
3. Step 3: Once you hear “click”, then you know the cord winder is ready for use.

NOTE: Once the installation of the cord winder has been completed. The cord winder cannot be removed. The installation is permanent.

USE & OPERATION

CONTROL PANEL

1. Power Control
2. Display Screen
3. Fan Speed Control
4. Humidity / Timer Set Controls
5. Timer Control
6.  Auto Drain Pump Mode
7. Auto Drain Pump Indicator Light
8. Comfort Mode Indicator Light
9. Timer Indicator Light
10. Water Full Indicator Light

• THIS IS ONLY FOR MODEL TPFIT50PWK WITH BUILT-IN DRAIN PUMP

FUNCTION BUTTONS

POWER CONTROL
Press to switch the dehumidifier ON or OFF.

When the unit is switched ON, the Display Screen shows the current humidity percentage.

• Press +or – to select your preferred humidity level. The humidity is adjusted in increments of 5%by pressing +or –. The adjustable Relative Humidity (RH) range is between 35% RH to 80% RH. 3 seconds after setting the preferred humidity setting, the display will revert back to displaying the current humidity.
• IMPORTANT: There is a 5% threshold when the desired humidity setting has been reached. The compressor will shut off once the relative humidity is 5% lower than your desired setting. The fan will continue to run for up to 3 minutes to cool the motor and will then shut off. Operation restores once the relative humidity is 5% higher than your desired setting.
• Recommended Settings: It is recommended to leave the unit running at 35% humidity at
• High Fan Speed during the first 2 to 3 days until damp odors are removed. After a few days when the Relative Humidity has been reduced to a more comfortable level, press or to choose a higher RH% that maintains a comfortable humidity level thereafter. A recommended healthy humidity level is between 40% and 50%.
• NOTE: The humidity sensor senses current humidity in the surrounding area. It is normal for about a 5% variance above or below the actual relative humidity in the room. Therefore, if there is a slight variance, the unit may sometimes operate slightly longer or shorter than the set RH% level.

CO LAUNDRY MODE
To activate the CO Laundry Mode, press – the button on the Display c0 Screen until appears.
Press to set the desired fan speed. A higher fan speed results in faster moisture removal.
The dehumidifier runs continuously for more powerful dehumidification, which is suitable for drying clothing. Hang damp clothing in the same room as the dehumidifier, taking care not to allow wet clothes to hang over it, ensuring that no water drips onto the dehumidifier.
Keep windows/ doors closed for faster drying.

WATER TANK FULL ALERT
When the water tank is full, the compressor will automatically switch off, while the fan will keep running for another 3 minutes to cool down the system. A beep sound will then activate for 3 seconds and the icon will illuminate. To re-set, empty the water tank and then re-install onto the unit, making sure the tank is secured properly in place.
IMPORTANT: Do not place the Water Tank on the floor when full. In case of an uneven base which may cause the tank to spillover.

TIMER CONTROL
The dehumidifier can be set to automatically switch ON or OFF for a selected period of time (between 0.5-24 hour intervals). The Timer hours selection is displayed on the Display Screen.
NOTE: Before setting the Timer control, make sure there is power to the unit.

Auto-Off Timer
While the unit is running, press , the timer indicator light will flash, press+ to- select the number of hours (0.5-24 hours) you want the unit to run before it switches off. In 5 seconds without the operation, the Timer ****start function, the timer indicator light is illuminated. Timer must be set again after each use.

Auto-On Timer
When unit is in Standby Mode, press , the timer indicator light will flash, press+ to- to select the number of hours (0.5-24 hours) until you want the unit to automatically start running. In 5 seconds without the operation, the Timer start function, the timer ****indicator light is illuminated. The previous fan speed and humidity setting will be maintained. The unit will turn on and continue running until the water tank is full (unless the unit is set up for continuous draining) or until you switch it off manually. Timer must be set again after each use.

NOTE

• To cancel any Timer settings, simply press ****again, and the timer indicator light will disappear.
• The solid power light indicates the tank of unit is full.
• “–“display in LED indicates the unit is on Standby Mode.

Fan Speed Control
There are 3 fan speeds – Low (I) – Medium (II) – High (III).

COMFORT MODE
When unit is in Standby Mode , hold for 3 seconds , and the indicator light will be illuminated.
The dehumidifier automatically adjusts Relative Humidity (RH) percentage settings based on ambient room temperature, for hassle-free operation (see below):

Ambient Room Temperature Dehumidification Target RH%

• 64°F (18°C) or lower 55% RH
• 64°F (18°C) to 77°F (25°C) 50% RH
• 77°F (25°C) or higher 45% RH

To cancel Comfort Mode, simply switch OFF the dehumidifier, or, hold the for 3 seconds and the indicator light will disappear.

DISPLAY AND WATER TANK ALERTS DEACTIVATED IN COMFORT MODE

Comfort Mode is designed for unobtrusive operation when sleeping:

• The display and control lights turn off after one minute of inactivity.
• Pressing any button will light up the control panel again.
• The water tank full alert light and beeping sounds are deactivated.
• When water tank is full, dehumidifier automatically turns OFF after 3 minutes.

NOTE: In other modes, the display and control lights automatically turn off after 3 minutes of control panel inactivity.

**AUTO DRAIN PUMP MODE*
The Auto Drain Pump function helps to remove condensation vertically and horizontally.
Press **the to activate the Pump function, ****the indicator light will be illuminated.
IMPORTANT: The pump function setting should be restored after a power outage. If it is not, simply reset and then turn on the pump feature again.

* THIS IS ONLY FOR MODEL TPFIT50PWK WITH BUILT-IN DRAIN PUMP

FROST ON COILS – AUTOMATIC DEFROST FUNCTION
Frost may build up on the internal coils of the unit. When there is frost build up, the internal compressor will turn off and the fan will continue to run until the frost has melted. Once the internal coils have defrosted and dried, the fan will continue to run for 8 minutes and the compressor will automatically restart and dehumidifying will resume.

DRAINING THE WATER
WARNING: Always drain and discard water collected from dehumidification.
The water is not clean and cannot be used for drinking.
WARNING: Clean the water tank with a soft cloth and a drop of dish detergent every 1-2 weeks to prevent mold formation in and around the water tank. Rinse with clean water and dry it before re-installing the tank into the unit.

1. Draining water collected in the Water Tank
2. The condensed water can be collected directly into the water tank. When the water tank is full, the dehumidifier will automatically shut OFF and the indicator will flash on the control panel followed by a beeping sound.

IMPORTANT: Do not move the dehumidifier when the Water Tank is full as it will be heavy and can cause water spillage.

1. Locate the water tank at the front of the dehumidifier. Gently pull the water tank out.
2. Grip the handle inside the water tank and carry the water tank to a sink to empty.
3. Replace the empty water tank back into the front of the dehumidifier. Please make sure that the tank is properly positioned. The safety feature ensures that any misalignment of the tank and the unit will prevent the unit from turning back on.

IMPORTANT: Improper alignment or positioning of the water tank will cause the unit to pause operation,  A beeping sound and warning light will flash when water  tank is not fitted properly*.

• Not applicable on TPFIT50PWK with built-in pump feature.

Continuous Water Drainage – Using a Continuous Water Drain Tube (CO Laundry Mode VERY IMPORTANT: DO NOT USE PUMP FUNCTION* when you connect a continuous water drain tube.

• THIS IS ONLY FOR MODEL TPFIT50PWK WITH BUILT-IN DRAIN PUMP

A continuous water drain tube is included with this unit. To activate the continuous water draining function, you will require a suitable water drain (e.g. sink or drain hole at floor level) near the dehumidifier.

Locate the drain outlet at the back of the unit. Unscrew and remove the Direct Drain Cap.
Insert the Continuous Water Drain Tube into the Direct Drain Outlet.

1. If there are leaks, the Continuous Water Drain Tube and Cap may have loosened and may not be connected properly. Disconnect, replace and tighten again.

2. Position the other end of the Continuous Water Drain Tube in the sink or drain. Make sure the tube is not bent or kinked which might stop the water flow. Make sure the tube is secured over the drain and will not fall out of place causing unwanted water spillage.
   IMPORTANT: Make sure water can flow down the Continuous Water Drain Tube by keeping the tube angled down and free of bends or kinks.
   IMPORTANT: If the unit is placed on uneven ground, or the Drain Tube is installed incorrectly, the water may fill the water tank and stop running. Please check whether the ground is uneven and reinstall the Drain Tube.

3. Continuous Water Drainage – Using the Auto Drain Pump option

VERY IMPORTANT : Only use pump function when you connect an Auto Drain Pump Tube.

The Auto Drain Pump is available if you want to use the continuous drain function, but the drain is further away, or located above the dehumidifier. The Auto Drain Pump Tube can be attached to the Direct Drain Outlet located on the back side of the dehumidifier.

1. Locate the drain outlet at the back of unit. Push Direct Drain Cap ① and the Auto Drain Pump Tube ② simultaneously.

2. To activate the Pump function , press button until is illuminated on the display screen.

3. Place the other end of the tube into the sink or drain. The water can be pumped up to 16.4 ft (5 m) vertically or horizontally.
   NOTE: DO NOT use an alternative drain tube that is longer than the one provided with the unit.
   IMPORTANT: The pump function setting should be restored after a power outage. If it is not, simply reset and then turn on the pump feature again.

4. To deactivate the Pump mode, simply press   again, and t he indicator light will disappear.
   To remove the auto drain pump tube. Push Direct Drain Cap ① and Pull the Auto Drain Pump Tube ② simultaneously

CLEANING & MAINTENANCE

WARNING: Always switch OFF the dehumidifier and unplug it from the electrical outlet before attempting any cleaning or maintenance of this product.

Appliance Maintenance

• Switch OFF the appliance before disconnecting the power supply.
• Only use a soft cloth to clean the appliance.

Dust Filter Maintenance
The Dust Filter located at the back of the unit helps to remove dust particles from the air. A dirty filter clogged by dust particles can reduce the efficiency of the dehumidifier. For optimum dehumidification, it is recommended to clean the dust filter every 2 weeks:

1. Switch off and unplug the dehumidifier from the electrical outlet.
2. Carefully pull out the dust filter from the dehumidifier.
3. Rinse the dust filter under running water, or vacuum away the dust with a vacuum cleaner.
4. After cleaning the dust filter, dry in a cool, shaded place, then carefully reinstall into the unit.

End of Season Storage & Maintenance
If the appliance will not be used for an extended period of time:

• Switch OFF the unit and unplug from the electrical power outlet.
• Empty the water tank and wash it gently with a cloth and a drop of dish detergent to remove any grime that may have collected inside or around the tank. This will help avoid mold formation while in storage. Rinse and dry the tank before re-installing onto the unit.
• If your dehumidifier is connected to the continuous drain hose, you must disconnect the hose, dry and then replace the drain cap back into the drain outlet.
• Remove the air filter and clean with water. Let the air filter dry and reinstall back into the unit. Make sure all parts of the dehumidifier and accessories are dry before storage.
• Cover the dehumidifier with a cloth/ plastic bag before storage, to protect the surface from dust and scratches.
• It is recommended to coil the power cord and store it off the floor to ensure it is protected from bends and kinks.
• Store the unit upright in a dry location, away from direct sunlight.

TROUBLESHOOTING GUIDE

The following troubleshooting guide addresses the most common problems. If problems persist, call customer service.
For more troubleshooting steps please visit: https://honeywellaircomfort.com/pages/portable-dehumidifier-faqs

cord.
The water tank is not in the correct position.| Position the water tank correctly into the unit. Unit will not operate until the water tank is secure in place.
Unit runs but the humidity level does not decrease| The humidity level setting is too high.| Decrease the humidity level setting.
A door or window is open, letting in new moisture.| Make sure all windows or doors to the outside are closed and tightly sealed.
There are other sources of humidity in the room (e.g. boiling water in pot).| Switch on the dehumidifier when these sources are not present.
The temperature in the room is too low.| The dehumidifier is designed to operate between 41°F (5°C) and 89°F (32°C). Moisture removal is greatly reduced if room temperatures exceed this temperature range.
The dust filter is dirty/ blocked.| Clean the dust filter.
Air outlet or intake is blocked, or drain outlet or drain tubes are blocked.| Remove blockage.
PROBLEM| POSSIBLE CAUSE| SOLUTION
---|---|---
Dehumidifier does not start| No electricity.| Check for power.
The power cord is not properly plugged in.| Remove and reconnect the power cord.
The water tank is not in the correct position.|

Position the water tank correctly into the unit. Unit will not operate until the water tank is secure in place.

Unit runs but the humidity level does not decrease| The humidity level setting is too high.| Decrease the humidity level setting.
A door or window is open, letting in new moisture.| Make sure all windows or doors to the outside are closed and tightly sealed.
There are other sources of humidity in the room (e.g. boiling water in pot).| Switch on the dehumidifier when these sources are not present.
The temperature in the room is too low.| The dehumidifier is designed to operate between 41°F (5°C) and 89°F (32°C). Moisture removal is greatly reduced if room temperatures exceed this temperature range.
The dust filter is dirty/ blocked.| Clean the dust filter.
Air outlet or intake is blocked, or drain outlet or drain tubes are blocked.| Remove blockage.
PROBLEM| POSSIBLE CAUSE| SOLUTION
---|---|---
Water on the floor| The garden hose/ drain hose may be loose.| Check the connections between the hose and the drain outlet on the unit. See Continuous Water Drainage section.

Check the tube of cap for tighten.

You intended to use the water tank to collect water but the continuous drain hose is still connected.| Disconnect the hose and replace the rubber stopper and drain cap if using the water tank to collect water. See Continuous Water Drainage section.
Noise| Fan is working.| Wind from the fan can create sounds during operation. This is a normal sound.
Compressor is working.| There is a sound when the compressor turns on. The compressor will activate periodically based on humidity settings. This is normal.

ERROR CODE GUIDE

• Check for Missing Washer(s): The rubber washers inside the drain cap can sometimes drop out of the cap. Check washer rings are in place inside the cap. If either is missing, please find and replace them onto the cap. If the washers are lost, please contact customer support.
• Reset the Unit: Turn dehumidifier OFF and unplug from power source for 24 hours and turn ON again.
• Contact Customer Support if the code reappears.

E1 / E2| Possible temperature sensor issue.| Reset the Unit: Turn dehumidifier OFF and unplug from power source for 24 hours and turn ON again.

Contact Customer Support if the code reappears.

E3| Refrigeration System Protection| If E3 appears, check if the ambient room temperature has exceeded 89.6oF (32oC). If yes, the unit may not run until the room ambient temperature has reduced to below 86oF (30oC) for at least 2 hours, or try to remove the unit to a cooler room for at least 2 hours before running dehumidification mode again.

Reset the Unit: If the code reappears, turn dehumidifier OFF and unplug from power source for 24 hours and turn ON again in a room with temperature below 86°F (30°C).

Contact Customer Support if the code reappears.

E5| Abnormal Pumping Drainage|

• Check that Auto Drain Pump Tube and Auto Drain Pump Cap are connected and properly installed.
• Check that the Auto Drain Pump Outlet and tube is clean and not jammed by sediments collected on and around the outlet or inside the tube.
• Check the air vents and exhaust vents are not blocked by any obstacles. Restricted airflow can cause internal temperature to rise and trigger the E5 error code.
• Check to see that the correct Auto Drain Tube is being used (the dehumidifier comes with a 16 ft/ 5 m long Auto Drain Pump Tube. The tube should not be longer than 16 ft/ 5 m.
• Check that the Auto Drain Pump Cap is securely screwed onto the Drain Outlet and no leakage is occurring due to
• unsecure connection.
• If all the above checks have been performed, reset the dehumidifier by unplugging and draining out all water in the water tank manually. Re-plug and turn ON again.
• If the code reappears, contact Customer Support.

REGULATION STATEMENT

FCC INTERFERENCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment info an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

INDUSTRY CANADA (IC) STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter.
Electrical products should be properly disposed of. Please recycle where facilities exist. Check with your local authority or retailer for recycling.

ENERGY STAR® qualified units remove moisture with less energy than conventional dehumidifiers.

Made in China © 2024 JMATEK Limited. All rights reserved. The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product. This product is manufactured by Airtek Int’l Corp. Ltd. (subsidiary of JMATEK Ltd.).

JMATEK North America
LLC Alpharetta, Georgia 30005 USA Phone: 1-800-474-2147 Email: usinfo@jmatek.com Web : www.HoneywellAirComfort.com

References

• HAC: Air Cooling Solutions for Almost Every Type of Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>