Antaira AMY5133ACPD Outdoor Wireless Bridge Installation Guide

Antaira AMY5133ACPD Outdoor Wireless Bridge Installation Guide

Device Installation

Device Installation

Working Environment:

Only applicable to areas below 2000 meters above sea level

Only applicable to non-tropical weather conditions

Wireless Connection Topology

Point to multiple point

In the wireless monitoring transmission, it is recommended to use the above graphic method for point-to-point or point-to-multi-point transmission. The wireless bridge/outdoor CPE transmission angle is oriented at 60 degrees. Please adjust the equipment’s angle when building point-to-multi-point transmission.

Point to Point

1P Camera — Warless Bridge Wireless Bridge — DVR — Monitoring PC. 1P Camera —Switch -Wireless Badge Wireless Bridge-— DVR —Monitoring PC.

Bridge Ways

0ne Key Bridge

1. Config Master/ Slave CPE Put the switch to H, CPE will work as Master. Put the switch to C, CPE will work as Slave.

Note: The pictures of the above products may change slightly according to the production cycle, and the final appearance is based on the physical object.

2. Point to Point Connection Press reset button on both master and slave CPE, wil start bridging Point to mult Point Connection Press reset button on master and mult slave CPES, wil start bridging,
   Note: Master CPE and slave CPE bridging actions (press reset bution) need to be finished in 1 minute,

LED Display Bridge

1. Config Master CPE
   When bridge two CPEs, make one work as master: press ‘F” to make H C blinking, and press change to”H’, it wil save automatically in 5 seconds.

2. Config Slave CPE
   Set another CPE to work as slave: press *F” to make H/ C blinking, and press ‘S to changeto °C”, will save automatically in 5 seconds.

Note:

1. GPE default working mode is AP mode after reset, IP s 192.168.188.253
2. F s select bution, can be used to choose master/ slave working mode, wifi channel, IP, and checking signal strength
3. 8 is config button, can be used to set master slave working mode, wifi channel, IP

3. Point to Point Connection
   Press reset button on both master and slave CPE, wil start bridging.
   Point to mult Point Connection
   Press reset button on master and mult slave CPES, willstart bridging.
   Note: Master CPE and slave CPE bridging actions (press reset button) need to be finished in 1 minute.

4. Change Wifi channel
   To avoid signal interference, need to change master CPE wifi channel only, slave CPE will reboot and bridge to master CPE automatically. Press F twice, change channel by press S, CPE will save and reboot automatically in 5 seconds.

5. Change IP
   To avoid CPE IP conflicts, need to change CPE IP address. Press F three times until the IP is blinking, press S to change IP, CPE will save and reboot automatically in 5 seconds.

Reset method

Press reset button in 10 Seconds will reseting device

Web Configuration

PC configuration if PC connect CPE by wireless

Set PC wireless network IP to 192.168.188.x (x: 2–250), same network segment as CPE, subnet mask: 255.255.255.0:

Check wireless connection

Adter IP address configuration, connect to CPE’s wireless SSID:
Wireless 5.8G, and input password (Default Password: 66666666)

Set wireloss network

Login Web Configuration 3.Bridge Status

N S Use IE browser to access http://192.168.188.253, pop up the login page shown Setup Wizard oo v ot below,input the login password: admin, enter into the home page.

Login Web Interface

Homepage

Setup Wizard

• Repeat mode
  Bridge the exist wireless signal then transmit Wi-Fi for more range

• AP mode 2 . . o
  In this mode, NAT, DHCR, firewall, and all WAN-related functions are tumned of. All wireless B and wired interfaces are bridged together, regardless of LAN and WAN

Bridge Status

Login CPE (work as repeater), will see signal strength, green is normal, between ; ~70dBm to -40dBm.

Channel Table

Trouble Shooting

1. Wireless Interference
2. Ctstance is too longer there are some bar between mem
3. CPE’s angle in wrong direction. weak signal

|

1. Dse Wi.Fi analysis to choose the best channel, or change to SG CPE
2. CPE snouid be in normal ckstance,and avoid bar
3. Adiust the angle of CPE according to signal strength

Wrong password|

1. Forget password
2. Input vrrong passwced
3. 700 muds cookie

|

1. Press reset button in 10 seconds to reset deuce, the defautt password is adman
2. Reenput the password
3. Ctear cookie,run arp
4. to dear MAC table

Can not logo WEB|

1. Local IP is not in the same network segment of CPE
2. IP a taken by other devices
3. LAN Connection or Ethernet cable has problem
4. Too much cookie. MAC address haven’t update

|

1. Ping 192.168.188253 to see connection status
2. 5100 other devices or change to another IP
3. Check LAN Connection and Ethernet cable
4. Clear cookie.nin arp -d to dear MAC address

System LEO light on|

1. PoE power supply is not working
2. Some problem in CPE’s PoE port
3. Ethernet cable is loose. R.M5 port is tenon Power currentivoltage lower or wrong

|

1. Check if POE Adapter or POE switch work
2. Check if POE port of CPE is OK
3. Check if Ethernet cable is loose,il Ethernet cable plugged in to POE port
4. Check it voltage is normal if socket has problem. it input voltage of POE adapter is normal

Low transmission Rate|

1. Packet Latency
2. Ethernet cable circuit
3. Network virus attack 4.Too much access users

|

1. Acipst the distance, angle and channel to decrease latency
2. Check if there S circuit in the network
3. Check if port isolated to avoid network veus and broadcast storm4.Decrease the access users

Device always dead|

1. Static electricity
2. Running time too long
3. Llghtning stroke

|

1. Make CPE or POE adapter need ground connection
2. Running time over 7 days, reboot it
3. Atter lightrong. devrte POE port broken or unstable. better to deploy Lightering conductor .

Login WEB by Mobile Phone

**Outdoor CPE support mobile phone Login and set, the configure page showed as follow:

**

Steps:

1. Mobile phone connect with outdoor CPE, SSID:Wireless5G, password:66666666, or please refer to product sticker for SSID, password.

2. Configure static IP
   Static IP address configuration on Android Mobile Phone
   Open settings in phone, turn on WLAN and find the SSID of the CPE, touch it for a long time until there is a menu,then choose”static IP” in the menu, set the mobile phone IP address as 192.168.188.X (X can not be 253 or 252), same network segment as CPE, subnet mask: 255.255.255.0, then gateway, subnet mask and domain.
   Static IP address configuration on IOS Mobile Phone
   Open settings and choose Wi-Fi, connect with CPE, click exclamation mark, manual to set IP address 192.168.188.X (X can not be 253 or 252) and subnet for mobile phone, note: mobile phone’s IP address should be same network segment as CPE.

3. Input 192.168.188.253 on the internet explorer bar, input admin to login the mobile configuration page.

Android system setup steps

IOS system setup steps

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user” s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm the radiator your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>