makita ADP05 USB Charging Adapter Converter Instruction Manual
- June 3, 2024
- Makita
Table of Contents
makita ADP05 USB Charging Adapter Converter Instruction Manual
SYMBOLS
Read instructions.
SAFETY INSTRUCTIONS
Important safety instructions for battery cartridge
-
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
-
Use the product only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
-
Before using battery cartridge, read all instructions and cautionary markings on battery charger, battery, and product using battery.
-
Do not disassemble battery cartridge.
-
If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
-
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
-
Do not short the battery cartridge:
- Do not touch the terminals with any conductive material.
- Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
- Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
-
Do not store the product and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).
-
Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out.
The battery cartridge can explode in a fire. -
Be careful not to drop or strike battery.
-
Do not use a damaged battery.
-
Follow your local regulations relating to disposal of battery
Tips for maintaining maximum battery life
-
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life. -
Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F).
-
Let a hot battery cartridge cool down before charging it.
-
Charge the battery cartridge if you do not use it for a long period (more than six months).
-
For an optimum life-time, the battery cartridge has to be fully charged, after use
SAVE THESE INSTRUCTIONS.
SPECIFICATIONS
| Model | ADP05/ADADP05 |
|---|---|
| USB power supply | Ports |
| Output voltage | D.C. 5V |
| Output current | 2.1A (each ports) (4.2A in total) |
| Input rating | D.C. 14.4 – 18V, 5A |
max.
Max. operating temperature| 40 degree C (104 F°)
Battery cartridge| Size (L x W x H)| Weight
---|---|---
Without battery| 102 mm x 72 mm x
43 mm (4” x
2-13/16” x 1-11/16”)| 0.11 kg (0.2 lbs)
BL1430B| 104 mm x 75 mm x 89 mm (4-1/8” x
2-15/16” x 3-1/2”)| 0.60 kg (1.3 lbs)
BL1815N/ BL1820B| 116 mm x 75 mm x 72 mm (4-9/16” x
2-15/16” x 2-13/16”)| 0.46 kg (1.0 lbs)
BL1830/ BL1830B/ BL1840B/ BL1850B/ BL1860B| 116 mm x 75 mm x 89 mm (4-9/16” x
2-15/16” x 3-1/2”)| **** 0.71 kg (1.6 lbs)
INSTALLING OR REMOVING BATTERY CARTRIDGE
(Fig. 1)
To install the battery cartridge (1), align the tongue on the battery
cartridge with the groove in the product and slip it into place. Insert it all
the way until it locks in place with a little click. If you can see the red
indicator (2) on the upper side of the button, it is not locked completely.
Always install the battery cartridge fully until the red indicator cannot be
seen. If not, it may accidentally fall out of the battery holder, causing
injury to you or someone around you.
Do not install the battery cartridge forcibly. If the cartridge does not slide
in easily, it is not being inserted correctly.
To remove the battery cartridge, slide it from the product while sliding the
button (3) on the front of the cartridge.
CONNECTING USB DEVICE (
(Fig. 2)
CAUTION:
• Connect only devices which are compatible with DC5V, 2.1A power source to the USB power supply port. Otherwise it may cause malfunction to the product.
Connect the USB cable (not included) with the power supply port (4) of the
product. And then connect the other end of the cable with the device To start
charging, move the slide switch (5) to “ON” side. To stop charging, move the
slide switch (5) to “OFF” side.
You can also hang the product on your belt.
NOTE:
-
Before connecting USB device to the product, always backup your data of USB device.
Otherwise your data may lose by any possibility. -
The product may not supply power to some USB devices.
-
Do not insert a nail, wire, etc. into USB power supply port. Otherwise a circuit short may cause smoke and fire.
-
When not using, move the slide switch to “OFF” side. Otherwise the battery capacity may be reduced during course of time.
-
When not using or after charging, remove the USB cable and close the cover.
-
After charging or during storage, remove the battery cartridge from the adapter.
FCC statements
Cautions to the user
The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
The equipment has been tested and found to comply with the limits for a Class
B Digital Device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communication. However,
there is no grantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
ICES-003 STANDARD :
CAN ICES-003(B)/NMB-003(B)
MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for the most current warranty terms
applicable to this product. If annexed warranty sheet is not available, refer
to the warranty details set forth at below website for your respective
country.
United States of America:
www.makitatools.com
Canada: www.makita.ca
Other countries: www.makita.com
References
- Makita Canada | The Leader In Power tool Technology
- MAKITA Industrial Power Tools - The Leader In Cordless with 18V LXT Lithium-Ion
- Makita U.S.A | Cordless and Corded Power Tools, Power Equipment, Pneumatics, Accessories