FLOW Subaru VA WRX/STI Front Splitter Lip User Guide
- September 19, 2024
- FLOW
Table of Contents
Subaru VA WRX/STI Front Splitter Lip
Product Information
Specifications:
- Product: Front Splitter
- Manufacturer: Flow Designs Australia
- Origin: Designed and Manufactured in Australia
- Fitting: Subaru VA WRX / WRX STI
- Installation: No bumper removal required
Product Usage Instructions
Fitting Diagram
For best fitment, align corner and inside edge of splitter to
the inside edge of the OEM bumper before drilling.
Fitting Kit (A)
-
Mount bolts (A) through OEM holes first to align splitter.
Drilling not required to mount to 4 OEM holes. -
Drilling required to fasten to bumper. Use an 8mm drill
bit.
Installation and Fitting Services
If you encounter difficulties, seek professional advice from
authorized dealers listed on the website.
Installation Video
Follow the installation video guide for proper installation.
Important Note for Add-On Accessories
Do not overtighten fasteners into brass fittings. Hand tighten
only.
FAQ
Q: Is bumper removal required for installation?
A: No, bumper removal is not required for fitting the front
splitter.
Q: What should I do if I encounter difficulties during
installation?
A: Seek professional advice from the authorized dealers listed
on the manufacturer’s website.
FITTING DIAGRAM
SUBARU VA WRX / WRX STI : FRONT SPLITTER
HANDY HINT
For best fitment, align corner and inside edge of splitter to the inside edge
of the OEM bumper before
drilling.
b
FITTING KIT (A)
a
Mount bolts (A) through OEM holes first to align splitter. Drilling not
required to mount to 4 OEM holes.
b
INSTALLATION AND FITTING SERVICES
If you are having any difficulties please seek professional advice from the
listed International and Domestic Authorised Dealers
on our website. www.flowdesignsaustralia.com
BUMPER REMOVAL NOT REQUIRED
FLOW DESIGNS AUSTRALIA ABN : 99 605 842 199
10 LONGSTAFF RD BAYSWATER VIC, 3153
DESIGNED AND MANUFACTURED IN AUSTRALIA
TERMS AND CONDITIONS: MISUSE OF GOODS
By taking possession of the Flow Designs Australia product, you (the buyer)
agree that you have read, understood and will comply with the following
disclaimer;
· This product may not be suitable for road use in your area. We cannot be
held liable for any penales or infringements that may occur aer installing any
of our products.
· We cannot guarantee that this product will comply with all subsequent
aermarket products you have applied to your vehicle. · It is not legal to fit
parts onto a road registered vehicle unless it carries and meets the designs
rules and public road regulaons of your area, region
and/or country. · We do our best effort to consider safety when designing our
products. We want the scene to be a safe place for everyone!
This disclaimer absolves us (Flow Designs Australia) of any and all liability or breaches to any requirement as a result of installaon of our products.
www.flowdesignsaustralia.com
FRONT SPLITTER
INSTALLATION VIDEO
PLEASE NOTE!
FOR ADD ON ACCESSORIES
DO NOT
OVERTIGHTEN FASTENERS INTO BRASS FITTINGS
HAND TIGHTEN ONLY
FITTING KIT
a
M6 NYLOC NUT M6 25 OD M6 25 OD
M6 25MM
M6 BOLT 25mm LONG
X 4
PLEASE NOTE: DRILLING NOT REQUIRED TO FASTEN TO BUMPER
USE OEM HOLE
b
M6 NYLOC NUT M6 25 OD M6 25 OD
M6 25MM
a
M6 BOLT 25mm LONG
X 8
PLEASE NOTE: DRILLING
REQUIRED TO FASTEN TO BUMPER USE 8MM DRILL BIT
FITTING KIT (A)
Mount bolts (A) through OEM holes first to align splitter. Drilling not
required to mount to 4 OEM holes.
HANDY HINT
For best fitment, align corner and inside edge of splitter to the inside edge
of the OEM bumper before
drilling.
a
b
b
a
b
b
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>