IPMIT450 IPMITTER 5.8GHz 48V 900Mbps IP Bridge User Guide
- June 6, 2024
- IPmitter
Table of Contents
IPMIT450 IPMITTER 5.8GHz 48V 900Mbps IP Bridge
User Guide
www.systemq.com/pdf/manual/xIPMIT400.pdf
The IPMIT400s can be used to “bridge” a wireless IP connection for IP cameras or other IP devices wireless between two points, devices connect via the RJ45 port on the IPmitter.
Powering
Option 1 – Power from 12V DC (via the 2.1mm DC Socket), the current
consumption is 300mA. The IPMIT400 is polarity sensitive so connections must
be made correctly.
Option 2 – Power the camera using 48V PoE, in the RJ45 WAN/POE Socket
The IPMIT400 will take approximately 1 minute to boot up.
1 = Function Button
2 = LED Display
3 = Setting
4 = 12V DC. 2.1mm DC Socket
5 = Reset/Pair Button
6 = WAN – 10Mbs / 100Mbs / 1000Mbs 48 PoE network socket
7 = LAN – 10Mbs / 100Mbs network socket
Standard WiFi Bridge Setup
For more setup options see the full manual
Available Channels – 36, 40, 44, 48
The matters are sent out as default on C048 (Client and channel 48) and need
pairing up before installing. One matter needs to be set to H (Host) and the
other to C (Client), they both have to be set to the same channel number.
Example – Pairing on channel 48
- Press the F (function) button and “C” will flash. Press the S (setting) button to change to “H048”
- Press the F button 4 times to move across the display, then the whole display will flash for about 5 seconds to indicate the settings have been saved.
- Now press the RST (reset) button for 1 second on both IPmitters. The display will change to a P with a rotating segment whilst pairing and will show P and a value once paired. Pairing can take up to 2 minutes.
The strength will range from P-01 (Good) to P-75 (Poor). If P-95 shows then
the IPmitters have not paired.
To add more clients (up to 4) to one host then set the channel on the new
client and press the reset buttons on the new client and the Host.
www.zipdvr.com/howto/TIP459-How-To-Add-
IP-Cameras.html
If using the IPMIT400 with a ZIP Recorder then the cameras need to be manually configured, scan the QR code to the left for the “how-to guide”
| LAN Port 1 Speed | 10Mbs / 100Mbs |
|---|---|
| LAN Port 2 Speed | 10Mbs / 100Mbs / 1000Mbs |
| Frequency | 5.8Ghz |
| Wireless Data Speed | 900Mbps |
| Wireless Standard | IEEE802.11AC/A |
| PoE Voltage | 48V |
| 12V Input Option | Yes |
| Max Tx Distance | 2000m (Recommend 1000m) |
| Easy Pair Technology | Yes |
| Support 1 – 1 | Yes |
| Support 1 – Many | Yes |
| Modes | Access Point / Bridge / Repeater |
| Mounting | Wall Or Pole (Not Supplied) |
| Dimensions | 260 x 88 x 56mm |
All specifications are approximate. System Q Ltd reserves the right to change
product specifications or features without notice. Whilst every effort is made
to ensure that these instructions are complete and accurate, System Q Ltd
cannot be held responsible for any losses, no matter how they arise, from
errors or omissions in these instructions, or the performance or non-
performance of the equipment referred to.
Quick Start Guide – qIPMIT400
Copyright 2021 System Q Ltd
This symbol indicates that equipment must not be mixed with general household
waste. For treatment, recovery, and recycling please return to your local
designated WEE/CG0783SS collection point as defined by your local council.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>