MAGICSHINE ALLTY1200U Underneath Mounted Bike Light User Manual

MAGICSHINE ALLTY1200U Underneath Mounted Bike Light

SAFETY WARNING

1. To prevent inadvertent switching on, please keep the light unit in lockout mode before transport or storage.
2. DO NOT disassemble, modify, remanufacture, puncture, or damage the device or batteries.
3. Before transporting or storing the remote control, please set it to lockout mode to avoid accidental activation and unnecessary battery consumption.

IN THE BOX

OPERATING INSTRUCTIONS

• ON/OFF: Press and hold the button for 1 second to turn the light on/off.
• ADJUST BRIGHTNESS: When the light is on, click the button to change the brightness level. The output brightness will cycle through Low→Medium→High→Low… When in flash mode, it will cycle through Night Flash→Day Flash→Night Flash.
• CHANGE MODE: When the light is on, double-click the button to change between constant mode and flash mode.
• LOCKOUT: When the light is off, press and hold the button for 3 seconds to enter lockout mode.
• UNLOCK: In lockout mode, press and hold the button for 3 seconds or charge the light.
• MEMORY FUNCTION: When the light is turned on again, it will automatically turn to the last selected lighting mode.
• LOW POWER MODE: When the battery power is below 10%, the indicator will flash red and the light will automatically turn to Low mode and cannot be adjusted. Charge the light as soon as possible.

OUTPUT/RUNTIME

• All data are measured in accordance with ANSI/NEMA FL 1-2009. The test was conducted at a temperature of 25°C and a wind speed of 25 km/h. The runtime may vary depending on external temperature and ventilation conditions, and these deviations may affect the result of testing.
• All data are measured under ANSI/NEMA FL l-2009. The test was conducted at a temperature of 25°C and a wind speed of 25 km/h. The runtime may vary depending on external temperature and ventilation conditions, and these deviations may affect the result of testing.

CHARGING/BATTERY INDICATOR

• Standard charging time approx. 2.5 hours (5V 2.4A)
• Charging: Flashing red
• Fully charged: Constant green
• BATTERY INDICATOR When the light is on, the Indicator will display the remaining battery level in real time. When the light is off, click the button to display the remaining battery level for 2 seconds
  • 100%-21%: Constant green
  • 20%-11%: Constant red
  • 10%-1%: Flashing red

HOW TO INSTALL

1. INSTALL THE OUT-FRONT MOUNT
2. REMOVE THE OUT-FRONT MOUNT
3. REMOTE CONTROL MOUNTING

REMOTE CONTROL INSTRUCTIONS

REMOTE CONTROL PAIRING

• LOCKOUT:
  Press and hold any button for 5 seconds to enter lockout mode. When locked out, the indicator will flash red for 3 seconds.

• UNLOCK:
  When in lockout mode, press and hold any button for 5 seconds to unlock or charge the remote. When unlocked, the indicator will constantly be green for 3 seconds.

• PAIR WITH A FRONT LIGHT: Turn on the light press and hold the and buttons on the remote for about 5 seconds until the indicator flashes blue to enter pairing mode. Then, hold the remote close to the light button until the indicator on the light unit flashes blue. Click the or button on the remote, and the indicators on the remote and light unit are constantly blue for 2 seconds, confirming a successful pairing.

• PAIR WITH A FRONT AND TAIL LIGHT: Turn on the front and tail lights, press and hold the and buttons on the remote for about 5 seconds until the indicator flashes blue to enter pairing mode. Then, hold the remote close to the front and tail lights until the indicators on the remote and the two light units are constantly blue for 2 seconds, confirming a successful pairing. (Note: The front and tail lights to be paired should support the FTR LightSync Control function, and the remote control cannot be paired separately with a tail light)

• CLEAR PAIRING: When the front light is off, double click the button and long press for 10 seconds until the indicator on the light unit flashes blue for 3 seconds, and the pairing is cleared successfully.

• ON/OFF: Press and hold the or “D” button for 1 second

• ADJUST BRIGHTNESS: Click the “O” button

• FLASH MODE: Double-click the “D” button

• FULL OUTPUT MODE (1200LM): Click the button to go into full output mode and click the or” ” button to return to the previous mode.

• FTR LIGHTSYNC CONTROL FUNCTION: After the remote control is successfully paired with the front and tail lights, press and hold the “ ” or” ” button on the remote for 1 second to turn on/off the front and tail lights simultaneously, or use the remote to adjust the modes and brightness of the front light.
  (Note: After successful connection, if the front and tail lights are disconnected, the indicator will flash blue for 3 seconds each time the front light is turned on/off or lit.)

CHARGING INDICATOR

Standard charging time approx. 1 hour (5V 0.065A)

• Charging: Flashing red
• Fully charged: Constant green

BATTERY INDICATOR

The indicator on the remote can display the remaining battery level of the light unit and the remote control.

• 100%-21%: Constant green for 1.5 seconds
• 20%-11%: Constant red for 1.5 seconds
• 10%-1%: Flashing red for 6 seconds
• Remote 10%-1%, light unit 100%-21%: Constant green for 1.5 seconds, then flashing red for 3 seconds
• Remote 10%-1%, light unit 20%-11%: Constant red for 1.5 seconds, then flashing red for 3 seconds.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>