Midea MSHC30TW6BB 30 Inch Smart Digital Tower Heater User Manual
- September 15, 2024
- Midea
Table of Contents
Midea MSHC30TW6BB 30 Inch Smart Digital Tower Heater
Warning notices : Before using this product, please read this manual
carefully and keep it for future reference.
The design and specifications are subject to change without prior notice for
product improvement.
Consult with your dealer or manufacturer for details.
The diagram above is just for reference. Please take the appearance of the
actual product as the standard. The device is only suitable for well insulated
spaces or occasional use.
THANK YOU LETTER
Thank you for choosing Midea! Before using your new Midea product, please read
this manual thoroughly to ensure that you know how to operate the features and
functions that your new appliance offers in a safe way.
Intended Use
The following safety guidelines are intended to prevent unforeseen risks or
damage from unsafe or incorrect operation of the appliance. Please check the
packaging and appliance on arrival to make sure everything is intact to ensure
safe operation. If you find any damage, please contact the retailer or dealer.
Please note modifications or alterations to the appliance are not allowed for
your safety concern. Unintended use may cause hazards and loss of warranty
claims.
Explanation of Symbols
Read these operating instructions carefully and attentively before using/commissioning the unit and keep them in the immediate vicinity of the installation site or unit for later use!
SAFETY INSTRUCTIONS
When using electrical heaters, basic precautions should always be followed to
reduce the risk of fire, electric shock, injury to persons, and hyperthermia,
including the following:
CAUTION
- Read all instructions before using heater.
- Extreme caution is necessary when any heater is used by or near children or invalids, and whenever the heater is left operating and unattended.
- CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. To do so could result in an electric shock hazard.
- It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace a loose or worn outlet.
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).
- TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.
WARNING
-
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, always use handles when moving this heater. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
-
Always unplug the heater when not in use.
-
Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater or return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
-
Do not use the heater outdoors.
This heater is not intended for use in bathroom, laundry areas and similar moist indoor locations. Never locate heater where it may fall into a bathtub or other water container. -
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
-
This heater draws 12.5 amps during operation.
To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working. -
To disconnect the heater, first turn controls to off, then remove plug from outlet. Never pull by the cord.
-
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire or damage to the heater.
-
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
-
A heater has hot and arcing or sparking parts inside.
-
Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
-
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
-
The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.
-
Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.
-
To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a confined space around infants, or individuals with reduced physical, sensory, or mental capabilities.
-
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
- Please note that any changes or modifications of this product not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Midea America Corp.
Parsippany, NJ 07054
TEL: 1-866-646-4332
SPECIFICATIONS
Product Model MSHC30TW6BB
Voltage 120V-
Frequency 60Hz
Rated Power 1500W
Rated Power
- LOW 600W
- MEDIUM 900W
- HIGH 1500W
- LOW/OSC 600W
- MEDIUM W/OSC 900W
- HIGH W/OSC 1500W
PRODUCT OVERVIEW
Part Name
Part List
NOTE All the pictures in this manual are for explanation purpose only. Any discrepancy between the real object and the illustration in the drawing shall be subject to the real subject.
OPERATION INSTRUCTIONS
Check Before Use
- Check for any damage to the power cord.
- Before connecting the heater to the power source, ensure the heater is positioned on a stable, flat, and even surface, clear of any obstacles.
- The product uses a 120V AC power supply, before use, please confirm if the rated current of the receptacle meets the local requirements as a safe device, otherwise, please replace it with the qualified receptacle.
Panel Operation and Display Indicators
Display Area Indicators
According to related safety standards, the power status indicator ” “should always illuminate red when the unit is powered on
NOTE
According to related safety standards, WiFi control of the heating functions
will be disabled under the following conditions: manual activation of any
control at the heater, movement of the heater (i.e. lifting, dropping, etc.),
or when the temperature of the heater reaches its set point (ECO mode only)
and/or exceeds an ambient temperature of 86°F. If any of these conditions are
met the heater will enter WiFi Standby mode (Press ” ” to reconnect)
Additional Functions
Forced shutdown function
If the machine keeps running for 24 hours without any operation, it will
automatically shut down.
Temperature sensor short circuit, open circuit protection function
The heater will display “E1” or “E2” error code if the temperature sensor
detects a short circuit or open circuit.
Safety protection
If the room temperature (TH) exceeds 122°F, the heater will shut down all
outputs with error code “FF” display, flashing once per second for 75 times.
Unplug the unit, then plug in again to reset.
Tip-over switch
The heater will display “P4” error code if it is knocked over. Place the
heater upright and power it back on.
ECO energy saving function
Select the ECO mode and set the temperature to your desired comfort.
The heater will adjust its heating power by comparison between the room
temperature and set temperature. If the heater turns off frequently, please
raise the set temperature for longer heating.
Child lock function
Press and hold the ” ” button simultaneously in standby or power on mode
for 3 seconds, the display will be locked and show the “[ ]” icon. Then long
press again can unlock the display. Please note that this function can only be
realized through the control panel rather than remote control.
Remote Control Operation
- Use of the remote control. Please refer to the tower heater panel operation and display section for the key functions of the remote control.
- The remote control can be used in front of the product within 15 ft.
NOTE
- Please use a manganese or alkaline battery of type “AAA” and do not use a nonrecyclable battery.
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.
APP CONNECTION
Download the SmartHome app
On an app market (Google Play Store, Apple App Store), search for SmartHome*
and find the SmartHome app. Download and install it on your phone. You can
also download the app by scanning the QR code below.
Register and log in
Open the SmartHome app, and create a new account to start (you can also
register through a third-party account). If you already have an existing
account, use the account to log in.
Connect your devices to SmartHome
- Please make sure your mobile phone is connected to a wireless network. If it is not, go to Settings and enable wireless networks and Bluetooth.
- Please power on your devices.
- Open SmartHome app on your phone.
- If a message of “Smart devices discovered nearby” appears, click to add.
- If no message appears, select “+” on the page and select your device in the list of nearby devices available. If your device is not listed, please add your device manually by the device category and device model.
- Connect your device to the wireless network according to instructions on app. If the connection fails, please follow the instructions provided by the app to continue with the operation.
NOTE
-
Make sure your device is powered on.
-
Ensure that both your mobile device and the heater is within the coverage range of the wireless network so that you can control the device through the mobile app.
-
Connect your mobile phone to the wireless network, and have the password of the wireless network available.
-
Ensure that your wireless network device supports 2.4GHz. This heater will only connect to 2.4 GHz wireless networks and does not support 5 GHz wireless networks.
Support from the wireless network device might be required to configure a 2.4GHz wireless network. -
The device cannot connect to a wireless network that requires authentication, and it usually appears in public areas such as hotels, restaurants, etc. Please connect to a wireless network that does not require authentication.
-
Turn off the WLAN+ (Android) or WLAN Assistant (iOS) function of your mobile phone when connecting your device to the network.
-
In the case that your device previously connected to a wireless network but needs to reconnect, please click “+” on the app home page. Add your device again by selecting the device category and model according to the instructions in the app.
CLEANING AND MAINTENANCE
It is recommended that the heater be cleaned at least one time during the operating season in order to provide the optimum level of performance. ALWAYS TURN THE POWER SWITCH OFF AND UNPLUG THE HEATER BEFORE CLEANING. Be sure to save the box for off-season storage.
- Turn the heater “OFF”, unplug it and wait for the heater to cool down.
- Use a dry cloth to clean only external surfaces of the heater.
- Do not use any cleaning agents or detergents.
- Never immerse the heater in water.
- Pack the heater in the original carton and store it in a cool, dry place.
- Any other maintenance shall be performed by an authorized service agent.
WARNING
This heater cannot achieve accurate temperature control of the environment,
and thus cannot be used as an insulation device for storage environment,
items, animals and plants.
TROUBLESHOOTING
If the product does not operate or does not operate properly, first check according to the following list. If the reason the product does not operate or does not operate properly is not included in the following list, the product mayhave failed. At this time, please contact your local Midea dealer.
PROBLEM
After the power is engaged, the machine does not work.
The machine suddenly stops during heating.
| POSSIBLE CAUSE
• The plug may not be properly inserted into the receptacle.
| SOLUTION
Check whether the plug is properly inserted into the receptacle.
---|---|---
• The temperature exceeds the threshold of the thermal cut-off.| Make sure
the appliance is powered-off and unplug. After the product has cooled,
reinsert the plug into the receptacle and power-on.
TRADEMARKS, COPYRIGHTS AND LEGAL STATEMENT
Midea logo, word marks, trade name, trade dress and all versions there of are valuable assets of Midea Group and/or its affiliates (“Midea”), to which Midea owns trademarks, copyrights and other intellectual property rights, and all goodwill derived from using any part of an Midea trademark. Use of Midea trademark for commercial purposes without the prior written consent of Midea may constitute trademark infringement or unfair competition in violation of relevant laws.
This manual is created by Midea and Midea reserves all copyrights thereof. No
entity or individual may use, duplicate, modify, distribute in whole or in
part this manual, or bundle or sell with other products without the prior
written consent of Midea.
All the described functions and instructions were up to date at the time of
printing this manual. However, the actual product may vary due to improved
functions and designs.
DATA PROTECTION NOTICE
For the provision of the services agreed with the customer,
we agree to comply without restriction with all stipulations of applicable
data protection law, in line with agreed countries within which services to
the customer will be delivered, as well as, where applicable, the EU General
Data Protection Regulation (GDPR).
Generally, our data processing is to fulfil our obligation under contract with you and for product safety reasons, to safeguard your rights in connection with warranty and product registration questions. In some cases, but only if appropriate data protection is ensured, personal data might be transferred to recipients located outside of the European Economic Area.
Further information are provided on request. You can contact our Data
Protection Officer via MideaDPO@midea.com To
exercise your rights such as right to object your personal date being
processed for direct marketing purposes, please contact us via
MideaDPO@midea.com. To find further information,
please follow the QR Code.
www.midea.com
© Midea 2022 all rights reserved
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>