rmkdesign RMK-05-GW01H-02 – Gloss Dry Carbon Gt Wing Kit Installation Guide
- July 4, 2024
- rmkdesign
Table of Contents
rmkdesign RMK-05-GW01H-02 – Gloss Dry Carbon Gt Wing Kit
PARTS LIST
ITEM
1
| DESCRIPTION
1500mm Dry Carbon Air Foil (wing)
| QTY
1
| NOTES
---|---|---|---
2| Aluminum Stands – Right side| 1|
3| Aluminum Stands – Left side| 1|
4| Billet Aluminum Base Plate – Right side| 1|
5| Billet Aluminum Base Plate – Left side| 1|
6| Foam Pads| 2|
7| Hex drive M8 x 15mm Button Head bolts, color: black| 4| Torque ~95 inch/
lbs.
8| Hex drive M6 x 25mm Button Head Bolts, color: black| 4| Torque ~55 inch/
lbs.
9| M6 Locking Flange Nuts, color: black| 4|
10| M6 Nylon Washers (not pictured below)| 8|
11| M8 Nylon Washers (not pictured below)| 4|
REQUIRED TOOLS
Required
- Hex Drive 5mm for M8 Flat Head Bolts
- Hex Drive 4mm for M6 Button Head Bolts
- 10mm Box Wrench
- 10mm Socket, extension, ratchet
- + drive screwdriver
Recommended
Torque Wrench in/ lbs.
INSTALLATION PROCEDURE
We recommend installation be performed by a professional. An assistant is recommended. Installation may vary if not being installed on an OEM trunk lid.
-
Remove the fabric cargo cover on the underside of the hatch.
-
Remove the plastic panels covers to access the tail lights on the interior hatch panel.
-
Flip open the covers on cargo cover mounts to access the tapping screw, and remove the screw for both sides.
-
Remove the cargo cover plastic mounts, both sides.
-
Remove the tapping screw located near the recess area on the plastic hatch panel.
-
Remove the plastic hatch interior cover. There are many plastic clips on the backside holding the panel in place as shown in the image below.
-
Using a 10mm socket CAREFULLY remove the six range head bolts securing the wing mounts to the hatch.
PRO TIP: Use a magnetic socket or be very careful not to drop the bolts into the hatch. -
With the OE wing assembly removed, thoroughly clean the painted surface of the hatch.
-
Attach the provided foam seals to the rmk Design billet aluminum mounts.
-
Attach the rmk Design mounts to the hatch using the original hardware. There are specific right and left mounts
PRO TIP: We found it best to insert one of the OEM bolts through the hatch, hold it in place with socket. Now, bring the mount to top side of the hatch and thread in hand tight. -
Insert remaining two bolts per mount, and just hand tighten so there is still some movement. Do NOT fully tighten at this point
-
Repeat on opposite side
-
Attach the rmk Design aluminum wing brackets to the rmk Design base mounts with provided M6 hardware and nylon washers. Snug all hardware.
-
Attach the wing element to the wing brackets and secure with supplied M8 hardware and nylon washers.
You can re-adjust the angle if needed at a later step.
We recommend either the second or third position.
Snug all hardware. -
Fully tighten and torque wing brackets to base mounts. Recommended ~55 in-lbs.
-
Fully tighten and torque wing element to wing brackets. Recommended ~95 in-lbs.
-
Now tighten the six OE bolts on the underside of the hatch to fully secure the mounts.
Torque to ~55 inch-lbs. or OEM spec -
Close the hatch and adjust the wing angle if desired.
-
Re-install all the interior hatch panel, cargo cover mounts, screws, and taillight covers.
-
Use soap and water or a quick detailer type product to clean the entire wing assembly.
WARRANTY POLICY
- 1-year limited manufacturer defect warranty from date of purchase.
- All warranty claims are subject to inspection by rmk-design at our facility.
- Limited Warranty only applies to the original purchaser of the product.
- rmk-design is not responsible for fitment issues on non-US spec vehicles as all products are developed on US spec models.
- It is the purchaser’s responsibility to ensure this product does not violate any City, County, State, or Federal laws or regulations.
- Product finishes are not covered under warranty and considered wear & tear. These are painted or powder coated part(s). The finish may be scratched, chipped, or damaged when tighten hardware, or components are attached to each other.
- No warranty whatsoever will be valid if the defect was caused by abuse, negligence and/or mishandling. That includes weather conditions, natural disasters, any road/off-road conditions, and any accidents/collision you were part of.
- Modification, mis-installation, tampering, and installation on vehicle not intended voids all warranty.
- Some chemical cleaning products may damage the product and/or finishes.
- Wear and tear (the damage that happens to our product in ordinary use) is not covered by our limited warranty.
- Improper installation or misuse of the product may lead to failure and damage to both product and vehicle. The user assumes all responsibility.
- Vehicle manufacturer warranty may be voided should any modification(s) OEM(factory) components are detemined.
- User assumes all cost and risks associated with purchase and installation of aftermarket components. rmk-design is not responsible for any fees, fines, or any type of penalties you have received from any authority.
- Buyers are responsible for all return shipping fees unless otherwise noted.
- rmk-design does not cover any installation, uninstallation, labor fees, or related.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>