PHILIPS PDRxA Antumbra Modular Touch Installation Guide

September 9, 2024
Philips

PHILIPS-Logo

PHILIPS-PDRxA-Antumbra-Modular-Touch-Product

PHILIPS-PDRxA-Antumbra-
Modular-Touch-Product

Specifications:

  • Model: PDRxA
  • Revolution User Interface
  • X2 X2 DACM 10.5 mm (0.41 in)
  • V3 V4 116 mm (4.56 in) 84 mm (3.30 in) 65 mm (2.56 in)
  • IEC Pollution Degree II
  • IEC Overvoltage Category III
  • RS-485 DyNet
  • SELV/Class 2 (UL)
  • Input Voltage: 12 V, 24 V
  • Current Consumption: 120 mA, 60 mA
  • Maximum Current: 2 A

Product Usage Instructions

  • Installation:
    Devices must be installed by a qualified electrician by all national and local electrical and construction codes and regulations.

  • Safety Measures:
    To avoid proximity sensor false triggering, ensure all unearthed metal structures and mains cables are more than 30 cm (11.81 in) away from the user interface.

  • Compliance:
    This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B).

  • Temperature Limits:
    Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded.

  • Power Connection:
    Do not connect inputs to mains. Disconnect power before connecting or separating modules.

  • Cleaning:
    Refer to the Service Guide for full cleaning recommendations.

  • Manufacturer Website:
    For more information, visit www.dynalite.com.

FAQ:

  • Q: Can I connect the device directly to the mains?
    A: No, do not connect inputs to mains.

  • Q: What should I do to prevent false triggering of the proximity sensor?
    A: Ensure all unearthed metal structures and main cables are more than 30 cm (11.81 in) away from the user interface.

Devices must be installed by a qualified electrician by all national and local electrical and construction codes and regulations.

What’s In The Box

Tools Required

Dimension

PHILIPS-PDRxA-Antumbra-Modular-Touch-Fig- \(3\)

Features

PHILIPS-PDRxA-Antumbra-Modular-Touch-Fig- \(9\)

Installation Instructions

IEC Pollution Degree II

PHILIPS-PDRxA-Antumbra-Modular-Touch-Fig- \(4\)

To avoid proximity sensor false triggering, please ensure all unearthed metal structures and mains cables are more than 30 cm (11.81 in) away from the user interface.

PHILIPS-PDRxA-Antumbra-Modular-Touch-Fig- \(5\)PHILIPS-PDRxA-Antumbra-Modular-Touch-Fig- \(6\) PHILIPS-PDRxA-Antumbra-Modular-Touch-Fig- \(7\) PHILIPS-PDRxA-Antumbra-Modular-Touch-Fig- \(8\)

Federal Communications Commission (FCC) Compliance

Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Any modifications not approved by the manufacturer of this device could void the user’s authority to operate this device.

  • This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada: CAN ICES-3(B)/NMB-3(B).
  • Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded.

2024 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.

  • Do not connect inputs to mains.
  • Disconnect power before connecting or separating modules.
  • Refer to the Service Guide for full cleaning recommendations.

www.dynalite.com.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals