HIKVISION DS-KH9510-WTE1-B Network Indoor Station User Guide

HIKVISION DS-KH9510-WTE1-B Network Indoor Station

Appearance

1. Screen
2. Microphone
3. Unlock Button
4. RS-485/Relay Interface
5. Debugging Port
6. micro USB Interface
7. Loudspeaker
8. TAMPER
9. TF Card Slot
10. Alarm Terminals
11. Power Supply Interface
12. Network Interface

Note:

• The appearance of the device varies according to different models. Refers to the actual device for detailed information.
• The debugging port is used for debugging only.

Terminal and Wiring

• AIN1: Alarm Input 1
• AIN2: Alarm Input 2
• AIN3: Alarm Input 3
• AIN4: Alarm Input 4
• NO1: Normally Open
• NC: Normally Closed
• COM1: Common Interface
• AIN5: Alarm Input 5
• AIN6: Alarm Input 6
• AIN7: Alarm Input 7
• AIN8: Alarm Input 8
• GND: Grounding
• AO1: Alarm Output
• RS485-/RS485+: RS-485 Communication Interface

Installation

Mounting Accessories

• The wall mounting plate and the gang box are required to install the indoor station onto the wall.
• There are 2 sizes of the gang boxes adapted to the device.
• Size 1: 75 mm (width) × 75 mm (length) × 46 mm (depth).
• Size 2: 55 mm (width) × 101 mm (length) × 38.5 mm (depth).

Before you begin:

• Make sure the device in the package is in good condition and all the assembly parts are included.
• The power supply of the indoor station is 12 VDC. Make sure your power supply matches your indoor station.
• Make sure all related equipment are power-off during the installation.
• Check the product specification for the installation environment.

Wall Mounting with Gang Box

1. Cave a hole in the wall.
   Note: The suggested dimension of the installation hole should be larger than the gang box.

2. Insert a gang box to the hole chiseled on the wall.

3. Fix the wall mounting plate to the gang box with 2 screws.
   Notes: If you install the device with a gang box (75 mm (width) × 75 mm (length) × 46 mm (depth)), the upper and lower holeswill be applies.
   If you install the device with a gang box (55 mm (width) × 101 mm (length) × 38.5 mm (depth)), the upper and lower holes will be applies.

4. Hook the indoor station to the wall mounting plate tightly by inserting the plate hooks into the slots on the rear panel of the indoor station, during which the lock catch will be locked automatically.

Getting Started

Activate Indoor Station
You are required to activate the device first by setting a strong password before you can use the device.

1. Power on the device. It will enter the activation page automatically.
2. Create a password and confirm it.
3. Tap OK to activate the indoor station.

Quick Configuration

1. Choose Language and tap NEXT.

2. Set password reset method and tap NEXT.

   • Enter the Reserved Email address, then you can reset the password by email.
     Note: On the security questions settings page, you can tap Change to Reserved Email to modify the password reset method.

   • Tap Change to Security Question. Select 3 security questions from Deficiency List and enter the answers of the questions, then you can reset the password by answering security questions.

3. Set gesture password and confirm it.

4. Set network parameters and tap NEXT.

   • When you select the connection type as Wired, you can edit network parameters manually or automatically.
   • Edit Local IP, Subnet Mask and Gateway parameters.
   • Enable DHCP, the device will get network parameters automatically.
   • When you select the connection type as Wireless, Select Wi-Fi from the drop list to connect.

5. Configure the indoor station and tap NEXT.

   • Select Indoor Station Type.
   • Edit Floor No. and Room No.
   • Enable the Custom SIP Registration Password function and set the Registration Password.
   • (Optional) Enable Link Indoor Extension and select device to link.
   • (Optional) Tap Advanced Options to edit Community No., Building No. and Unit No.

6. Slide to enable the mobile client service and set the LBS Server. Tap NEXT.

7. Linked related devices and tap NEXT. If the device and the indoor station are in the same LAN, the device will be displayed in the list. Tap the device or enter the serial No. to link.

   • Tap the door station in the list to link.
   • Tap the settings icon to pop up the Network Settings page.
   • Edit the network parameters of the door station manually or enable DHCP to get the network parameters automatically.
   • Tap OK to save the settings.

8. Tap Finish to save the settings.
   The power supply must conform to LPS.

The recommended adaptor models and manufacturers are shown as below. Use the attached adapter, and do not change the adaptor randomly.

2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.

About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the
latest version of this Manual at the Hikvision website (https://www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product. HIKVISION and other Hikvision trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITY FOR ABNORMAL OPERATIONS, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACKS, HACKER ATTACKS, VIRUS INFECTIONS, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.

CE

This product and -if applicable the supplied accessories too are marked with CE and comply therefore with the applicable harmonized European
standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symb0l, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info

References

• Hikvision - Leading Video AIoT Solutions & Services Provider
• HOME
• Hikvision USA - Leading the future of AIoT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>