belldinni DIY Friendly Door Kit Installation Guide
- September 5, 2024
- belldinni
Table of Contents
belldinni DIY Friendly Door Kit
Belldinni DIY Friendly
Specifications:
- Ready to be installed like a pre-hung door kit with Easy Installation kit
- QR code to have EZ installation instructions on your phone
Product Usage Instructions
Necessary Tools (not included):
- Pencil
- Garbage bags
- Screwdriver Screw 1 5/8
- Tape measure
- Level
- Safety glasses
Door Parts (some fixtures may not be included):
- Shims (not included)
- Header
- Screw inside white connector 4 pcs (B)
- Black 4 pcs. opposite connector (C)
- Dowel 2 pcs (D)
- Quick hanger 6 pcs (may not be included) (E)
- Screw 6 pcs. (F)
- Screw 18 pcs. (G)
- Strike plate jamb Hinges side jamb
Do:
- Check your order
- Connect the door frame
- Attach ez hangers
- Lay out the markings
- Install the door frame
- Align and screw in the door frame
- Screw the hinges to the door slab
- Screw on the door hinges
- Install the door slab
- Adjustment and installation
- Moldings installation
Don’t:
- Use standard nails and hammer
- Step on the door
- Lay down or lean on edges or the wall
Warning:
Please do not throw away the packing cardboard until the end of the
installation.
FAQ:
-
Q: What should I do if I encounter small deviations during installation?
A: Small deviations are acceptable as long as the door slab does not touch the floor or any side of the jamb. -
Q: Are all necessary tools included in the kit?
A: No, necessary tools such as a pencil, garbage bags, screwdriver, tape measure, and level are not included in the kit.
Belldinni DIY Friendly
Ready to be installed like a pre-hung door kit with Easy Installation kit
QR code to have EZ installation instructions on your phone
Safety
NECESSARY TOOLS
Not included 
DOOR PARTS
(some fixtures may not be included)
WARNING!
Please do not throw away the packing
STEP 1.
Check your order
Check the contents of your door unit according to the door parts description
above (page 3)
If you have any problems or questions please contact us via
diy@belldinni.com or by phone # 646 680 3191
Measure roungh opening to make sure all sizes are correct:
Door slab should be at least 2” narrower than the opening width, we recommend
the door slab to be 2,5” narrower than the opening width. Door slab should be
at least 2” shorter than the opening height.
Check swing directions according to the chart below
STEP 10.
Adjustment and installation
- Check and adjust the hinge side of the jamb according to the level first.
- Fix the hinge side jamb to the wall with the help of EZ hangers, “A” screws ( 1 5/8”) (not included) and shims (not included) if needed.
- Unscrew the screws of the strike plate side (handle side) of the jamb.
- Align the door slab within door jamb (frame) minding the gaps between the door slab and the door jamb.
- Hinge side of the jamb is already fixed to the wall, so the strike plate side of the jamb and the header jamb need to be adjusted.
- Please note, metal EZ Hangers have the ability to be bent. In some installation cases you would need to bend them during the door installation to be as close as possible to the best installation result.
- Fix the strike plate side (handle side) of the jamb and the header jamb to the wall with the help of EZ Hangers, “A” screws ( 1 5/8”) (not included) and shims (not included) if needed.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>