Klima IEC227 Cooker Hood User Guide

: September 4, 2024
: klima

Table of Contents

Klima IEC227 Cooker Hood
Product Usage Instructions
SLIDE HOODS GUIDE
GENERAL
INSTALLATION INSTRUCTIONS
USE AND MAINTENANCE
Finding the problems and maintance
Frequently Asked Questions (FAQ)
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Klima IEC227 Cooker Hood

Product Specifications

Model: IEC227
Dimensions: 65 cm x 3 mm
Power: 65 cm
Pressure: 4Pa (4×10-5 bar)

Product Usage Instructions

General Safety Precautions

Before connecting the model to the electricity network, ensure the voltage and power match the network and socket specifications.
If unsure, consult a qualified electrician.

WARNING!

Do not check filters while the cooker hood is operating.
Avoid touching bulbs or adjacent areas during or immediately after prolonged use of the lighting installation.
Do not engage in flambe cooking under the cooker hood.
Avoid free flame as it is damaging to the filters and poses a fire hazard.
Constantly monitor food frying to prevent overheated oil from becoming a fire hazard.
Disconnect the electrical plug before performing any maintenance.
This appliance is not intended for unsupervised use by young children or infirm persons.
Ensure young children are supervised to prevent them from playing with the appliance.
Keep the room well ventilated when using the rangehood simultaneously with gas or fuel-burning appliances.
Follow cleaning instructions to avoid fire risks.

Installation Instructions
Assembly and electrical connections must be done by specialized personnel.

Electric Connection

The appliance is class I, so an earth cable is required for connection to the mains.

Slide Hoods Guide
Refer to Fig.1 to Fig.9 for visual guidance on slide hoods.

SLIDE HOODS GUIDE

GENERAL

Carefully read the following important information regarding installation safety and maintenance. Keep this information booklet accessible for further consultations. The appliance has been designed for use in the ducting version (air exhaust to the outside – Fig.1B), filtering version (air circulation on the inside – Fig.1A) or with external motor (Fig.1C).

SAFETY PRECAUTION

Take care when the cooker hood is operating simultaneously with an open fireplace or burner that depend on the air in the environment and are supplied by other than electrical energy, as the cooker hood removes the air from the environment which a burner or fireplace need for combustion. The negative pressure in the environment must not exceed 4Pa (4×10-5 bar). Provide adequate ventilation in the environment for a safe operation of the cooker hood.

Follow the local laws applicable for external air evacuation.
Before connecting the model to the electricity network: control the data plate (positioned inside the appliance) to ascertain that the voltage and power correspond to the network and the socket is suitable. If in doubt ask a qualified electrician.

WARNING!
In certain circumstances electrical appliances may be a danger hazard.

Do not check the status of the filters while the cooker hood is operating.
Do not touch bulbs or adjacent areas, during or straight after prolonged use of the lighting installation.
Flambe cooking is prohibited underneath the cooker hood.
Avoid free flame, as it is damaging for the filters and a fire hazard.
Constantly check food frying to avoid that the overheated oil may become a fire hazard.
Disconnect the electrical plug prior to any maintenance.
This appliance is not intended for use by young children or infirm persons without supervision.
Young children should be supervised to ensure they do not play with the appliance.
There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances burning gas or other fuels.
There is a risk of fire if cleaning is not carried out in accordance with the instructions

K) under the hood allow the use of up to 6 stoves.

L) range hood should not be routed to the exhaust gas for exhaust gas or other fuels used in hot flue smoke.

M) directly against the fire roasting hood.

N) If the power cord is damaged, can only use the company’s dedicated power line replacement.

O) non-professional non-disassembly of the machine.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out by specialized personnel.

Electric Connection
The appliance has been manufactured as a class I, therefore earth cable is necessary.

The connection to the mains is carried out as follow:

| IEC227| North America
---|---|---
L=live| Brown| Black
N=neutral| Blue| White
E=earth| Green/Yello| Green

If not provided, connect a plug for the electrical load indicated on the description label. Where a plug is provided, the cooker hood must be installed in order that the plug is easily accessible.
An omnipolar switch with a minimum aperture of 3mm between contacts, in line with the electrical load and local standards, must be placed between the appliance and the network in the case of direct connection to the electrical network.

The minimum distance between the support surfaces of the cooking pots on the cooker top and the lowest part of the cooker hood must be at least 65 cm.
Do not connect the cooker hood exhaust to the same conductor used to circulate hot air or for evacuating fumes from other appliances generated by other than an electrical source.
Before proceeding with the assembly operations, remove the anti-grease filter(s) (Fig.5) so that the unit is easier to handle.
In the case of assembly of the appliance in the suction version prepare the hole for evacuation of the air.
Fasten the chimney hood.
First, install them in the positions with suitable selftapping screws after taking out, the drill the holes respecting the distances indicated (Fig.1) Fix the appliance to the wall and align it in horizontal position to the wall units. when the appliance has been adjusted, definitely fix the hood using the screws

If the model of your chimney hood need to shift from pipe emission to filter model ,you can get help from the installation instruction after you get the charcoal filters. （Fig.4）
To transform the hood from a ducting version into a filtering version, ask your dealer for the charcoal filters and follow the installation instructions.

FIX TERING VERSION
After installing the hood and the duct work, fix the filter as described in the paragraph for installation of the hood inside the hood. The charcoal filters must be fitted in the ducting unit located inside the hood. （Fig.3）

USE AND MAINTENANCE

Before using the hood, please open the pull-out shell.
It is recommended to operate the appliance prior to cooking.
It is recommended to leave the appliance in operation for15 minutes after cooking is terminated in order to completely eliminate cooking vapors and odour.
The proper function of the cooker hood is conditioned by the regularity of the maintenance operations, in particular, the active carbon filter.
The anti-grease filters capture the grease particles suspended in the air, and are therefore subject to clogging according to the frequency of the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the filter at a maximum of 2 months by carrying out the following instructions:

Remove the filters from the cooker hood and wash them in a solution of water and neutral liquid detergent, leaving to soak.
Rinse thoroughly with warm water and leave to dry.
The filters may also be washed in the dishwasher.

Before removing the filters, you should remove the outside filter first, then pull the pull-out shell to the farthest distance position prior to removing the inside filter.
When installing the filters, install the inside filter with the pull-out shell in the farthest distance position, and then install the outside filter.
The aluminum panels may alter in color after several washes. This is not cause for customer complaint nor replacement of panels.

The active carbon filters purify the air that is replaced in the environment. The filters are not washable nor re-useable and must be replaced at maximum every four months.(Fig.4)
To remove the charcoal filters place on hand on one filter at a time and turn it toward the front part.

The charcoal filter can now be removed. Always ensure to replace both filters at the same time.

Clean the fan and other surfaces of the cooker hood regularly using a cloth moistened with denatured alcohol or non abrasive liquid detergent.
The illumination installation is designed for use during cooking and not for prolonged general illumination of the environment. Prolonged use of the illumination installation notably reduces the duration of the bulb. Use a one-edged screwdriver or any other appropriate tool to lift and remove the overhead light fixture. Replace the damaged lamp. Use only halogen lamps as the original specification, avoiding contact with hands. Return the light fixture to its position . (Fig. 5)

COMMANDS:

A = TIMER – 15 MINUTES
B = SPEED I / OFF
C = SPEED II / OFF
D = SPEED III / OFF
E = LIGHT

When pressing the key B, the display light is flashing and please run in SPEED 1.If you want to stop, you only press the key A.
When pressing the key E, the display light is flashing and then turn on the light, If you want to turn off the light, you only press the key once again. (Fig.6)

COMANDS:

A = OFF
B = SPEED I
C= SPEED II
D = SPEED III
E =LIGHT

When pressing the key B, the display light is flashing and please run in SPEED 1.If you want to stop, you only press the key A.
When pressing the key E, the display light is flashing and then turn on the light, If you want to turn off the light ,you only press the key once again . (Fig.7)

COMANDS:

A = SPEED II
B = OFF
C = SPEED I
D = SPEED III
E = OFF
F = LIGHT
G = OFF
H = LIGHT

When pressing the key H, the display light is flashing and then turn on the light, If you want to turn off the light, you only press the key G.
When pressing the key F, the display light is flashing and then turn on the light, If you want to turn off the light, you only press the key G. When pressing the key A, the display light is flashing and please run in SPEED II.If you want to stop, you only press the key B.
When pressing the key C, the display light is flashing and please run in SPEED I.If you want to stop, you only press the key B.

When pressing the key D, the display light is flashing and please run in SPEED III.If you want to stop, you only press the key E.

When the motor and the light work together or individually ,press the key A, and stop the activated functions of the timer automatically .The display light is flashing countdown which will continue functioning for 15 minutes ,and the motor and the lights will be turned off. For stopping the timer, only press the key once again. Manufacturers stated strictly that we refuse to take any responsibility because of the results caused by any violation of the above procedures(Fig.8)

COMMENTS:

A= SPEED I
B = SPEED II
C= SPEED III
D= SPEED P
E = LIGHT

When pressing the key A, the display light is flashing and please run in SPEED

When pressing the key E, the display light is flashing and then turn on the light, If you want to turn off the light ,you only press the key once again . (Fig.9)

Finding the problems and maintance

Problem	Possible reason	Solution
Hood doesn’t work	No electric supply	Check the plug is connected

Check the main switch is

turned on

Unfold the pull-out shell| Folded the pull-put shell
Poor airflow| Aluminum grease

filters clogged

| Clean the filters and replace

when dry

Charcoal filters clogged| Replace the charcoal filters
Motor running but

no air flow

| Butterfly valve jammed| Contact technician
Motor cuts after a| High temperature

safety device activated

| The kitchen is not

sufficiently ventilated

The hood is installed

too near the cooking

| The hood must be least 65cm

from stove

Strong cooking smell| Charcoal filters not| In re-circulating mode, charcoal filters must be
Oil dripping onto stove| Oil cup missing or

not installed

| Remove aluminum filter and replace oil cup
Aluminum grease filter saturated| Wash the aluminum grease filters
Whirring sound| Something in contact| Contact with technician

This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children should not play with the product. Cleaning and maintenance works should not be performed by children unless they are supervised by someone. Children under the age of 3 should be kept away unless continuously supervised.

Packaging materials are dangerous for the children. Keep packaging materials in a safe place away from reach of the children.
Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do not allow them to play with the product. Use child lock to prevent children from intervening with the product.