POSIFLEX TX-2300-G2 Fanless POS Box User Manual
- September 2, 2024
- POSIFLEX
Table of Contents
POSIFLEX TX-2300-G2 Fanless POS Box
Specifications
- Model: TX-2300-G2/TX-2300E-G2
- Power: 12VDC-IN
- Ports: Mic-in & Line-out Combo, CR port (RJ10), COM ports (RJ50), COM ports (DB9), USB 2.0 ports, USB 3.0 ports, LAN port (RJ45), VGA port, HDMI ports
- Warranty: Void if the machine is opened by unauthorized personnel
- Compliance: CE Class A – CISPR 32
Product Usage Instructions
Connecting Power Adapter and I/O Cables
- Connect the power adapter to DC-IN power connector on the I/O plate.
- Connect the other end of the power adapter to the electrical outlet.
CAUTION: When inserting or extracting cable connectors, always hold the connector head to avoid damage.
Mounting the TX-2300-G2/2300E-G2 on the Wall (Optional)
- Refer to the WB-4200 installation guide to fix the wall mount bracket onto the wall using plastic anchors and screws.
- Insert four screw bolts into the 4 screw bolt holes.
- Align 4 screw bolts to four mounting holes of the wall-mount bracket and slide down the system until it is locked into place.
Powering ON/OFF TX-2300-G2/2300E-G2
- Power ON: Press down the power button to turn on the system.
- Power OFF: Push the power button again to power off the system. If halting, hold the power for more than 10 seconds for a forced shutdown.
Power Status LED Indicator
The LED indicator notifies users of the system status by emitting various
signals. Refer to the chart for LED status interpretation.
FAQ
Q: What should I do if my machine halts for unknown reasons?
A: Hold the power button for more than 10 seconds to initiate a forced
shutdown.
Package Contents
- POS box…………………………………..…………………………..(x 1)
- Power adaptor………………………………..…………………….…(x 1)
- Power cord………………………………………..…………………..(x 1)
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user should consult his/her dealer for the problem happening. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be present.
WARNING
Power cord shall be connected to a socket-outlet with earthing connection.
BATTERY WARNING
Risk of explosion if battery is replaced by an incorrect type. Dispose of
expended battery in accordance with local disposal regulations.
Views of the TX-2300-G2
Views of the TX-2300E-G2
View of Rear I/O Interface of TX-2300-G2/2300E-G2
- Mic-in & Line-out Combo
- CR port (RJ10)
- COM ports (RJ50)
- COM ports (DB9)
- USB 2.0 ports
- USB 3.0 ports
- LAN port (RJ45)
- VGA port
- HDMI ports
- 12 VDC-IN power jack
Connecting Power Adapter and I/O Cables
Please follow the steps described below to connect power adapter and I/O
cables.
- Connect power adapter to DC-IN power connector on the I/O plate
- Connect another end of power adapter to the electrical outlet.
CAUTION: On doing insertion or extraction of a cable connector, please always hold the connector head itself instead of pulling the cable wire. Doing this could damage the cables and ports, which is considered as an artificial damage and is not covered by the warranty. The means of power cord should be connected to a socket-outlet with earthing connection.
Mounting the TX-2300-G2/2300E-G2 on the Wall (Optional)
Please follow the steps described below to mount TX-2300-G2/2300E-G2 onto the
wall using WB-4200 wall-mount kits.
- Refer to WB-4200 installation guide to fix the wall mount bracket onto the wall using plastic anchors and screws
- Insert four screw bolts into the 4 screw bolt holes.
- Align 4 screw bolts to four mounting holes of the wall-mount bracket as shown in the figure. Then slide down the system along the rail until it is locked into place with a click sound.
Powering ON/OFF TX-2300-G2/2300E-G2
- Power ON TX-2300-G2/2300E-G2
- Press down the power button to power on TX-2300-G2/2300E-G2.
Power OFF TX-2300-G2/2300E-G2
In most cases, push the power button again to power off the system. However,
if TX-2300-G2/2300E-G2 halts for unknown reasons, please be advised to hold
the power more than 10 seconds to initiate a forced shutdown.
Power Status LED Indicator
Power LED indicator is mainly responsible for notifying users of the current
system status by emitting various LED signals. The chart provided below will
offer helpful information that you need to interpret LED status.
| LED | Status | Description |
|---|---|---|
| Power | Solid green | System power ON |
| Solid red | System standby | |
| Storage | Flash green | Data access |
Installing Optional Peripheral Devices
TX-2300-G2/2300E-G2 can work with multiple optional peripheral devices, such
as LCD monitor, cash drawer and the like. Before installing an optional
peripheral device, make sure that the system is powered off and the external
power source is removed from the POS box to prevent electric hazard. For the
detailed instruction, refer to each of the user manuals of the optional
peripheral devices.
Installing an Operating System
You are highly advised not to install an operating system on TX-2300-G2/2300E-G2 without professional instructions. Improper installation could lead to system malfunction or failure. Please contact with your dealers about the issues of operating system installation.
Driver Download
If your POS terminal is shipped without OS pre-installed, please download the
relevant driver that you need from the Posiflex website
(https://download.posiflex.com/en-global/Download/index/driver/POS-
Box/TX-2300-G2).
Operating System Recovery
For TX-2300-G2/2300E-G2 models with preloaded operating systems, you are not
encouraged to recover your system without the help of system integrators.
Please be advised to contact your service center for further assistance with
system recovery.
Operation Environment
To prevent TX-2300-G2/2300E-G2 from overheating, it is suggested to position
your terminal in a well-ventilated working environment. In doing so, please be
advised to keep the POS box at least 25mm away from other devices to ensure
the machine is properly cooled down and functioning normally.
Specifications
| TX-2300-G2 | TX-2300E-G2 | |
|---|---|---|
| CPU | Intel Elkhart Lake Celeron J6412 (default) Intel Elkhart Lake Celeron |
N6210
System Memory| DDR4 SO-DIMM socket x 2
Storage Port| 1 x M.2 socket (M.2 2280 / B+M key)
Power Supply| 12V/60W| 12V/150W
OS support| Windows 10 IoT (64-bit)
Serial Port
| ****
2 x DB-9 COM ports + 2 x RJ-50 COM ports
| 2 x DB-9 COM ports + 2 x RJ-50 COM ports +
COM5/6 pin headers in service window
Parallel Port| 1 port (header in service window)
Standard USB Port| 4 x USB 2.0 + 2 x USB 3.0 port
LAN Port| 1 x 10 /100 /1000 Mb
| TX-2300-G2| TX-2300E-G2
---|---|---
Display Port| 2 x HDMI port + 1 x VGA port
CR Port| 1 port, controlling 2 CRs
PS/2 Port| 1 port, on the front bezel
DC Jack| 1 port
Expansion Slot| 1 x M.2 socket (M.2 2230 / E key) for WiFi/BT module
Audio| 1 x Mic-in & Line-out combo jack + 1 x internal speaker
LED Indicator| Bi-color power LED
PoweredUSB port| N/A| 1 x 24V (via PU-470
module)
Dimension (W x D x H in mm)| 220 mm x 202 mm x 56 mm
Weight| 1.2 kg
Regulation Rules| FCC/CE
Environmental Requirements| Operating : 0°C – 40°C, 20%RH – 90%RH
Storage : -20°C – 70°C, 10%RH – 90%RH
Outline Dimension
The product information and specifications are subject to change without prior notice. To get the detailed information on TX-2300-G2/2300E-G2, please check this model from Posiflex Global Website (https://download.posiflex.com/en- global/Download/index/driver/POS-Box/TX-2300-G2).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>