Hi-LTTE HT-360T 360 LED Outdoor Projector User Manual

HT-360T
360 LED ZOOM PROJECTOR IP65 USER MANUAL

HT-360T 360 LED Outdoor Projector

Foreword
Thank you for choosing our 360 LED Outdoor Projector, which is the latest high-quality projector light developed by Hi-LTTE LIGHTING. It is ultra compact and more convenient in the same power products. This projector combines the characteristics of international advanced electronic control technology and outstanding humanized industrial design.
It fully complies with the CE standard and supports the international DMX512 signal control mode, it also support radar sensing activation system.
The equipment is fitted with long lifespan top LED module, with strong light effect, clear gobo, circular smoothing motor and accurate positioning, uniform color wheel.
Meanwhile it has 6 colorful gobos, and a color wheel with 10 color + 1 open. And it also has a 3-facet prism.
360 LED is widely used in outdoor projects.

**Safety Instructions

**

Before using this product, please carefully check the product is not unwrapped or damage during transport. In case of damage caused by transportation, please do not use this equipment, and contact your dealer or manufacturer as soon as possible.
Before turning on the product, ensure that the voltage and hertz to meet the requirements of this product.
It is very important, connecting the ground wire to avoid electric shock.
This product must be installed on the sufficient space, adjacent to interface the shortest distance of 50cm, to ensure that the lights will not crash each other.
Before moving or repairing the product, please unplug the power.
When it working, ensure that no inflammable and explosive near objects.
Please carefully read the instructions, this guide consists of important information about installation, using and maintenance.
When installing this product, please use the safety rope. When handling this product, lift the armrest base, rather than the lamp body.
The product is suitable for minus 20 to 45 degrees Celsius, when the surrounding environment is higher than 45 degrees Celsius, please do not use this product. Please remarks if lower than minus 25 degrees Celsius.
Do not touch when the equipment is working.
If there is a problem with the operation during using, the equipment should be stopped immediately. Do not perform repairs, damage or repairs that may occur during maintenance. Please contact the company’s service point for repair. Use the same model of accessories during the repair process. During the repair process, use the same type of accessories.
Please read this manual, especially regarding the installation, use, maintenance parts. It is important that the moving head light must have anti- vibration protection carton or flight case during transportation.

Technical Parameters

DMX Channel: 13CHs
Control Mode: DMX512, RDM, support radar sensing activation system
LED LCD Display + Press Button
Source: Top LED 360W Module Light Source
Color temperature is 8000K, life span is 20,000Hs
10 Colors + Open, Semi Color Effect
Gobo: 6 Rotating gobos
Prism: 3-Facet Prism
Optical lens: High precision glued optical lens combination
Zoom: 14-45°
Dimmer: 0-100% Linear Dimmer Adjustment
Strobe: Electronic strobe
Motors: 8pcs super mute sound motors, 16bit
Housing: High temperature, ultraviolet and oxidation resistant alloy plastics
Rated Power: 420W
Luminous Flux: 23000LM
IP Rate: IP65
Weight: 13.3 KG
Size: 509220347mm

Schematic Lighting Components

Packing And Shipping

4.1 Packing Material and Accessories
360 LED Gobo Projector is packaged by carton or flight case. Accessories items as show below.

4.2 Packing

1. Power off to let the lamp cool completely before packaging equipment at least 15 minutes or more.
2. Lock the light when cleaning the surface of the light.
3. Use the packing bag to cover the light, put it into the box gently.
4. Add lighting accessories after putting the light into packing box.
5. It’s only up to two crates stacked and is prohibited upside down.

4.3 Unpacking

1. Open the packing box and packing bag.
2. Seizing the equipment’s handles, lifting and carrying away the light from the packing box or opening the flight case cover placing lift boom close to the light base, then equipping light hook on light base bottom tightening quick Install locks. At last rising away boom to the top of the lamp from flight case, put the flight case away.

Installation

Note: Upon receipt of lamps, please check if there is damage to the fold closure caused by transport, where there is transportation damage, please do not use this fixture, and contact us as soon as possible.
5. Safety Standard
Users should ensure that light and installation materials are checked for regular safety checks. Unprofessional incorrect installation can lead to dangerous, if the lack of working conditions and professional standards, please operate the light by professionals.
Do not use the light if the working temperature isn’t minus 25 – 45 degrees Celsius. Don’t stand directly under the light when the light is installed, dismantled, moved or serviced. The operator must ensure that the fixtures are securely connected. Installing the light after professionals approving electrical parameters make sure that these installation must be checked at least once per year by experts.
5.1 Hook Clamp Installation
200W LED could be placed on the truss or on a stand in any direction with M8 stainless steel screws and clamps.
5.2 Fixing Equipment

1. Before installing fixtures must verified rigging equipment is not damaged, and can bear at least 10 times of light’s weight.
   Check the building can be bore at least 10 times of total weights of light, fixture, and cable accessories.

2. Use a wrench to connect the M8 stainless steel screws to the lamp body bracket to themounting part.

Note 1: Lights be placed vertically upward, the shortest distance between working lights must be more than or equal 500mm, lighting installation layout as picture.

5.3 Data cable
Data cable is DMX512 signal.
Note: Signal line connections is X-type connector.
X-type connector—–If the external flexible  cable or cord of this light is damaged, please replace professional cable or cord from the manufacture or its agent.
Lights’ DMX input and output connects to a 3&5pin XLR, first pin is grounded, then negative signal is second pin, third pin connects to the positive polarity signal, the fourth and fifth is empty.
In order to prevent reception reflection and interference control signal, a terminal plug must be installed on the first branch of the connected device last 3-pin output jack.

The controller connects to the nearest input XLR 3-pin, then from the output of the device connects to the input of the next device, continuous connection one by one, the final output data cable terminal equipment plug one end into the terminal.

5.3 Data cable
If the signal transmission is long-distance, DMX 512 signal amplifier must be added. DMX512 signal controller connect to the input of the amplifier first, then connect to the fixture from its output, couple with the terminal plug last.
Note:

1. Do not use two separate output connections. To connect the branch, a separating consecutive DMX512 signal amplifier must be used to separate.
2. Please use the specialized DMX512 shielded twisted-pair cable. Standard microphone cables can not be reliably controlled long-distance data.

Power Connection

If the external flexible cable or cord of this light is damaged, please contact the manufacturer or its agent or a similar qualified person to replace, in order to avoid danger.
Connect the power supply personnel must have the appropriate qualifications before proceeding, you must make sure you are using the power supply voltage matches the voltage identified and have overload or leakage protection. Directly connect the device to the power supply, do not connect to the silicon box dimming system, otherwise damage to the equipment.

LED Chip

360 LED uses top LED 360W light source module, this LED light source + concentrator integrated light source provides a very stable color temperature at 8000K, Color rendering index 70 or 90 is optional, and average life is more than 20,000 hours (according to leds Relevant use environment).
Note:

1. Please do not install other similar led light source, otherwise it will cause safety hazards or damage the equipment.
2. To reduce the risk of damage to the light, replace the LED Chip before it exceeds the life of the lamp.
3. It is forbidden to use damaged LED Chip.

FUNCTIONS

8.1 Glass Gobo Wheel
6 glass gobos, gobos can be customized (customized gobos are chargeable).
8.2 Color Wheel
The color wheel consists of 10 colors,users can easily choose the color they want and create a perfect lighting effect. At the same time, it can be used with the gobo wheel, to have a better effect. Colors can be customized. (customized colors are chargeable).

8.3 Zoom Function
Zoom Angle:14-45°
8.4 Dimming and Strobe
0-100% electronic dimming, instant switching, stroboscopic speed can be adjusted, up to 0.520 times / sec, with special function of random strobe.

LCD Display

9.1 Display Board

9.2/Menu Operation:

360 led zoom projector|
---|---
1.DMX Address:1-512|
2.Channel Mode:13|
3.Reset| 1. Power on/ off| YES/NO|
2.Color| YES/NO|
3.Gobo| YES/NO|
4.Zoom/Prism| YES/NO|
4.DMX Setting| 1.Number Set| Number Set| Any model / Only same model
2.Destination Address| Destination
Address by number
Uniform Address
5.Operation| DMX/Human Sensing/Auto1/Auto2/Auto3/User Program
---|---
6.Manual Control| 1.Color| 0-255|
2.Gobo Wheel Rotation| 0-255|
3.Gobo auto rotation| 0-255|
4.Prism| 0-255|
5.Focus| 0-255|
6.Zoom| 0-255|
7.Strobe| 0-255|
8.Dimmer| 0-255|
9.Prism Auto Rotation| 0-255|
10.Auto Return| Never/30s/2 Min|
7.Running Setting| 1.dimming curve| Line/square/root /S curve/logarithm
2.Master-Slave Mode| Master/Slave|
3.Mixed scene| Play Scene| 1-12
First Scene| A-H
| | Second Scene| A-H|
---|---|---|---|---
Third Scene| A-H|
Fourth Scene| A-H|
Fifth Scene| A-H|
Sixth Scene| A-H|
Seventh Scene| A-H|
Eighth Scene| A-H|
4.Scene Editing| Scene Editing| A-H|
Step Number| 0-29|
Step Editing| Time| 0-255
Channel| 1-25
Number| 0-255
Copy| |
Paste| |
Recording| |
| 5.Switching light in| Gobo| Yes/No|
---|---|---|---|---
6.Color Linear Switching| Yes/No| |
7.Motion sensing operation mode| DMX/Auto1/Auto2/ Auto3/User Program| |
8.Display Setting| 1.Sleeping| 30S/10 Min/Never| |
2.Brightness| 1-10S| |
3.Inverted display| Yes/No| |
4.Indicator light| Auto/Always| |
5.Blinks when no signal| Yes/No| |
9.Advanced Setting| 1.Fine| Color| -500 ～ 500|
Focus| -500 ～ 500|
Prism Rotation| -500 ～ 500|
Gobo Wheel Rotation| -500 ～ 500|
Gobo Rotation| -500 ～ 500|
Zoom| -500 ～ 500|
Lock the menu| Yes/No|
| 2.Factory Setting| | |
---|---|---|---|---
3.fine assistance function| Enter the fine menu simultaneously| |
Recovery| |
Back up| |
Fine value clear| |
view local data| |
4.When no DMX| execute| Middle/Keep/Human Sensing/ Auto1/Auto2/Auto3/User Program
5.Mode| Any time/Only when power on| |
6.Auto Power on| Yes/No| |
7.Advanced function channel| Yes/No| |
| | |
| | |
| 8.Fan speed| Auto/Full Speed| |
---|---|---|---|---
9.Language| Chinese/English/ Spanish| |
10.Lamp Using time clear| | |
11.Recovery Factory Setting| | |
12.Clarity Self-Program| | |
13.Disable power-on beam display| Yes/No| |
14.Open Synchronous setting| Yes/No| |
10.Information| 1.PMX Number Monitor| | |
2.Situation| | |
3.Lamp Using time| This time:Minutes| Total: Minutes|
4.Error Message| | |
5.Time Remaining| Infinite| |

Channel

360W LED ZOOM PROJECTOR

Channel| DMX Number| Function Description
13
1| | Strobe/Shutter
| 0-2| Close
| 3-7| Open
| 8-97| standard strobe, from slow to fast
| 98-101| Open
| 102-126| fast open slow close,from fast to slow
| 127-151| fast close slow open,from fast to slow
| 152-155| Open
| 156-180| fast open slow close,random strobe,from slow to fast
| 181-205| fast close slow open,random strobe,from slow to fast
| 206-209| Open
---|---|---
| 210-249| Random Strobe
| 250-255| Random Strobe
2| | Dimmer
| 0-255| Continuous dimming 0%-100%
3| | Dimmer Fine
| 0-255| Dimmer fine
4| | Color
| 1-5| white
| 6-11| white+blue
| 12-17| blue
| 18-23| blue+red
| 24-29| red
| 30-35| red+orange
| 36-41| orange
| 42-47| orange+yellow
---|---|---
| 48-53| yellow
| 54-59| yellow+green
| 60-65| green
| 66-71| green+purple
| 72-77| purple
| 78-83| purple+light green
| 84-89| Light green
| 90-95| Light green+brown
| 96-101| brown
| 102-107| brown+fluorescent purple
| 108-113| fluorescent purple
| 114-119| fluorescent purple+light blue
| 120-125| Light blue
| 126-127| Light blue+white
| 128-190| Clockwise color switching
| 191-192| stop
---|---|---
| 193-255| Anti-clockwise color switching
5| | Glass Gobo
| 0-5| Gobo 1
| 6-16| Gobo 2
| 17-27| Gobo 3
| 28-38| Gobo 4
| 39-49| Gobo 5
| 50-60| Gobo 6
| 61-83| Gobo 1 shake
| 84-106| Gobo 2 shake
| 107-129| Gobo 3 shake
| 130-152| Gobo 4 shake
| 153-175| Gobo 5 shake
| 176-198| Gobo 6 shake
| 199-201| Stop
| 202-227| Gobos clockwise switching,from fast to slow
---|---|---
| 228-229| Stop
| 230-255| Gobos anti-clockwise switching,from slow to fast
6| | Gobo Rotation
| 0| No action
| 1-127| Gobo indexing
| 128-191| Gobo clockwise rotation:from fast to slow
| 192-255| Gobo anti-clockwise rotation:from slow to fast
7| | Prism
| 1-63| No effect
| 64-255| Prism insertion
8| | Prism Rotation
| 0| no
| 1-127| Prism anti-clockwise rotation,from fast to slow
| 128-254| Prism clockwise rotation,from slow to fast
| 255| stop
9| | Zoom
---|---|---
| 0-255| Zoom from small to large
| 0-255| Zoom fine, from small to large
11| | Focus
| 0-255| Focus,from far to near
12| | Focus Fine
| 0-255| focus fine, from far to near
13| | Reset
| 0-209| Empty
| 210-229| All reset
| 230-255| Empty

Fault Analysis And Resolution

Listed below are a few common problems that you may encounter, with solutions.
Equipment does not work, no light output and the fan does not work;

1. Check the power connection and main fuse.
2. Be sure the voltage of the connector.

Not responding to DMX Console;

1. After connecting the controller, the equipment should be working. If it does not work properly, please heck if the signal plug and power cable is connected correctly.
2. If the DMX LCD display is on and no response to the channel, check the address settings and the polarity of DMX output voltage.
3. If the signal of the product is unstable, please check the input terminal and circuit boards.
4. Try using another DMX controller.
5. Check to see if the DMX cables run near or run alongside to high voltage cable. It may cause damage or interference to DMX interface circuit.

One of the channels is not working:

1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.

FIXTURE CLEANING

The cleaning of internal and external optical lenses or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Clean the external optics at least every 30 days.
Clean the fans on the head and base every 90 days.
NOTE:Disconnect the fixture before clear.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>